Endress+Hauser Proline Promass 80 Especificaciones técnicas

Products Solutions Services

KA00023D/06/EN/14.15

71230840

Brief Operating Instructions

Proline Promass 80

Coriolis flowmeter

These Brief Operating Instructions are not intended to replace

the Operating Instructions provided in the scope of supply.

Detailed information about the measuring device is provided in

the Operating Instructions and the additional documentation:

• On the CD-ROM supplied (is not included in the delivery for all

device versions).

• Available for all measuring device versions via:

– Internet: www.endress.com/deviceviewer

– Smartphone/tablet: Endress+Hauser Operations App

Table of contents Proline Promass 80

2Endress+Hauser

Table of contents

1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.2 Installation, commissioning and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.4 Safety conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.1 Transporting to the measuring point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.3 Post-installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

3.1 Connecting the various housing types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.2 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.3 Post-connection check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4 Hardware settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

4.1 Device address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

5.1 Switching on the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5.3 Navigating within the function matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5.4 Calling the Commissioning Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.5 Software settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

5.6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Proline Promass 80 Safety instructions

Endress+Hauser 3

1 Safety instructions

1.1 Designated use

• The measuring device should only be used to measure the mass flow rate of liquids and gases.

At the same time, the measuring device also measures the density and fluid temperature.

These parameters are then used to calculate other process variables such as volume flow.

• Any use other than that described here compromises the safety of persons and the entire

measuring system and is, therefore, not permitted.

• The manufacturer is not liable for damage caused by improper or non-designated use.

1.2 Installation, commissioning and operation

• The measuring device must only be installed, connected, commissioned and maintained by

qualified and authorized specialists (e.g. electrical technicians) in full compliance with the

instructions in these Brief Operating Instructions, the applicable norms, legal regulations and

certificates (depending on the application).

• The specialists must have read and understood these Brief Operating Instructions and must

follow the instructions they contain. If you are unclear on anything in these Brief Operating

Instructions, you must read the Operating Instructions (on the CD-ROM). The Operating

Instructions provide detailed information on the measuring device.

• The measuring device may only be installed in a de-energized state.

• Repairs may only be performed if a genuine spare parts kit is available and this repair work is

expressly permitted.

• If performing welding work on the piping, the welding unit may not be grounded by means of

the measuring device.

1.3 Operational safety

• The measuring device is designed to meet state-of-the-art safety requirements, has been

tested, and left the factory in a condition in which it is safe to operate. Relevant regulations

and European standards have been observed.

• Observe the technical data on the nameplate!

• The technical staff must ensure that the measuring device has been correctly wired and

grounded as per the wiring diagrams.

• With regard to special fluids, including fluids used for cleaning, Endress+Hauser will be happy

to assist in clarifying the corrosion-resistant properties of wetted materials. However, minor

changes in temperature, concentration or in the degree of contamination in the process may

result in variations in corrosion resistance.

For this reason, Endress+Hauser does not accept any responsibility with regard to the

corrosion resistance of wetted materials in a specific application. The user is responsible for

the choice of suitable wetted materials in the process. A sensor version which allows the

sensor housing be monitored should be used for critical fluids.

Safety instructions Proline Promass 80

4Endress+Hauser

• Hazardous areas

Measuring devices for use in hazardous areas are labeled accordingly on the nameplate.

Relevant national regulations must be observed when operating the device in hazardous

areas. The Ex documentation on the CD-ROM is an integral part of the entire device

documentation.

The installation regulations, connection data and safety instructions provided in the Ex

documentation must be observed. The symbol on the front page indicates the approval and

certification body (0Europe, 2USA, 1Canada). The nameplate also bears the

documentation number of this Ex documentation (XA***D/../..).

• For measuring systems used in SIL 2 applications, the separate manual on functional safety

(on the CD-ROM) must be observed.

• Hygienic applications

Measuring devices for hygienic applications have their own special labeling. Relevant national

regulations must be observed when using these devices.

• Pressure instruments

Measuring devices for use in systems that need to be monitored are labeled accordingly

on the nameplate. Relevant national regulations must be observed when using these devices.

The documentation on the CD-ROM for pressure instruments in systems that need to be

monitored is an integral part of the entire device documentation. The installation regulations,

connection data and safety instructions provided in the Ex documentation must be observed.

• Endress+Hauser will be happy to assist in clarifying any questions on approvals, their

application and implementation.

1.4 Safety conventions

#Warning!

"Warning" indicates an action or procedure which, if not performed correctly, can result in injury

or a safety hazard. Comply strictly with the instructions and proceed with care.

"Caution!

“Caution” indicates an action or procedure which, if not performed correctly, can result in

incorrect operation or destruction of the device. Comply strictly with the instructions.

Note! "Note" indicates an action or procedure which, if not performed correctly, can have an

indirect effect on operation or trigger an unexpected response on the part of the device.

Proline Promass 80 Installation

Endress+Hauser 5

2 Installation

2.1 Transporting to the measuring point

• Transport the measuring device to the measuring point in the original packaging.

• The covers or caps fitted on the process connections prevent mechanical damage to the

sensors during transport and storage. For this reason, do not remove the covers or caps until

immediately before installation.

2.2 Installation conditions

For mechanical reasons, and in order to protect the piping, it is advisable to support heavy

sensors.

2.2.1 Dimensions

For the dimensions of the measuring device →see associated Technical Information on the

CD-ROM.

2.2.2 Mounting location

The following mounting locations are recommended:

• Upstream from assemblies such as valves, T-pieces, elbows, etc.

• On the pressure side of pumps (for high system pressure)

• At the lowest point in an ascending pipe (for high system pressure)

A0007408

To transport the unit, use slings slung around the

process connections or use lugs (if available).

#Warning!

Risk of injury! The device can slip.

The center of gravity of the measuring device may be

higher than the holding points of the slings.

Always ensure that the device cannot slip or turn

around its axis.

A0007409

Do not lift measuring devices by the transmitter

housing or the connection housing in the case of the

remote version. Do not use chains as they could

damage the housing.

Installation Proline Promass 80

6Endress+Hauser

The following mounting locations should be avoided:

• At the highest point in a pipe (risk of air accumulating)

• In an open down pipe directly upstream from a free pipe outlet. For ways of using the

measuring device in down pipes, see the related Operating Instructions on the CD-ROM.

2.2.3 Orientation

• The direction of the arrow on the nameplate of the measuring device must match the flow

direction of the fluid.

• The following table lists the possible orientations of the measuring devices:

Vertical Horizontal Horizontal

A0004572 A0004576 A0004576

Transmitter at the side Transmitter at the top Transmitter at the

bottom

Promass A Recommended Possible (m) Possible (m, p)

Promass E Recommended Recommended (n) Recommended (o, p)

Promass F Recommended Recommended (n) Recommended (o, p)

Promass F HT*

Compact version Recommended Not suitable Recommended (o, p)

Promass F HT*

Remote version Recommended Possible (n) Recommended (o, p)

Promass H Recommended Recommended Recommended (p)

Promass I Recommended Recommended Recommended (p)

Promass P Recommended Recommended Recommended (p)

Promass S Recommended Recommended Recommended (p)

*HT = high temperature version for medium temperatures (TM) > 200 °C (> 392 °F)

mDo not install the measuring device in such a way that is suspended without any support or securing unit.

nThis orientation is not suitable for fluids with entrained solids.

oThis orientation is not suitable for outgassing fluids.

pThis orientation is not suitable for low fluid temperatures.

Proline Promass 80 Installation

Endress+Hauser 7

Special installation instructions for Promass A

"Caution!

Risk of measuring pipe fracture if sensor installed incorrectly!

The sensor may not be installed in a pipe as a freely suspended sensor:

• Using the base plate, mount the sensor directly on the floor, the wall or the ceiling.

• Support the sensor on a firmly mounted support base (e.g. angle bracket).

Vertical

We recommend two installation versions when mounting vertically:

• Mounted directly on a wall using the base plate

• Measuring device supported on an angle bracket mounted on the wall

A0018980

Horizontal

We recommend the following installation version when mounting horizontally:

• Measuring device standing on a firm support base

A0018979

2.2.4 Heating

For information on the heating, please see the Operating Instructions on the CD-ROM.

2.2.5 Thermal insulation

For information on the thermal insulation, please see the Operating Instructions on the

CD-ROM.

10 mm

4 x

Installation Proline Promass 80

8Endress+Hauser

2.2.6 Inlet and outlet runs

No inlet and outlet runs are required.

2.2.7 Vibrations

No measures are necessary.

Proline Promass 80 Installation

Endress+Hauser 9

2.3 Post-installation

2.3.1 Turning the transmitter housing

Turning the aluminum field housing

Aluminum field housing for non-Ex area

Aluminum field housing for Zone 1 or Class I Div. 1

Turning the stainless steel field housing

A0007661

A0007540

A0008036

a. Release the setscrew.

b. Turn the transmitter housing gently

clockwise until the stop (end of the

thread).

c. Turn the transmitter

counterclockwise (max. 360°) to the

desired position.

d. Retighten the setscrew.

£180° £180°

’

max. 360°

Nicht-eigensichere

Stromkreise durch

IP40-Abdeckung geschützt

Non-intrinsically safe

circuits Ip40 protected

Boucles de courant

sans sécurité intrinsèque

protégées par Ip40

£180° £180°

Installation Proline Promass 80

10 Endress+Hauser

2.3.2 Turning the onsite display

A0007541

a. Press in the side latches on the display module and

remove the module from the cover plate of the

electronics compartment.

b. Turn the display to the desired position (max. 4 × 45° in

both directions) and reset it onto the cover plate of the

electronics compartment.

4 × 45°

Otros manuales para Proline Promass 80

Tabla de contenidos

Otros manuales de Instrumento de medición de Endress+Hauser

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 93T Portable Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag D 400 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Solitrend MMP40 Manual de usuario

Endress+Hauser

Endress+Hauser SpectraSensors SS2100 Manual de usuario

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manual

Endress+Hauser

Endress+Hauser Proline Promag W 400 HART Manual de usuario

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag L 400 Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot FMR51 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Micropilot FMR20 Manual

Endress+Hauser

Endress+Hauser Cerabar M PMC51? Cerabar M PMP51 Manual de usuario

Endress+Hauser

Endress+Hauser Liquicap T FMI21 Manual de usuario

Endress+Hauser

Endress+Hauser RMM621 Manual de usuario

Endress+Hauser

Endress+Hauser RIA15 Manual de usuario

Endress+Hauser

Endress+Hauser Liquiphant M FTL50 Manual

Endress+Hauser

Endress+Hauser Raman Rxn2 Manual de usuario

Endress+Hauser

Endress+Hauser Levelflex M FMP40 Manual de usuario

Endress+Hauser

Endress+Hauser silopilot FMM 460 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag L 400 HART Manual de usuario

Endress+Hauser

Endress+Hauser Promass 40 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Guía de aplicación

Endress+Hauser

Endress+Hauser Conducal CLY421 Manual de usuario

Endress+Hauser

Endress+Hauser ria45 Manual de usuario

Endress+Hauser

Endress+Hauser Levelflex FMP55 Especificaciones técnicas

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Acterna

Acterna MS1400 Manual de usuario

R&S

R&S ZPH Manual de usuario