Endress+Hauser Liquiline CM442 Especificaciones técnicas
Products Solutions Services
Brief Operating Instructions
Liquiline
CM442/CM444/CM448
Universal four-wire multichannel controller
These instructions are Brief Operating Instructions; they are
not a substitute for the Operating Instructions pertaining to
the device.
Detailed information on the device can be found in the
Operating Instructions and in the other documentation
available at:
• www.endress.com/device-viewer
• Smart phone/tablet: Endress+Hauser Operations App
KA01159C/07/EN/07.21
71525975
2021-03-24
Liquiline CM442/CM444/CM448
2 Endress+Hauser
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0040778
Liquiline CM442/CM444/CM448 Table of contents
Endress+Hauser 3
Table of contents
1 About this document .............................................................. 4
1.1 Warnings ............................................................................ 4
1.2 Symbols ............................................................................. 4
1.3 Symbols on the device ................................................................... 5
1.4 Documentation ........................................................................ 5
2 Basic safety instructions .......................................................... 6
2.1 Requirements for personnel .............................................................. 6
2.2 Designated use ........................................................................ 6
2.3 Workplace safety ...................................................................... 7
2.4 Operational safety ......................................................................7
2.5 Product safety ......................................................................... 7
3 Incoming acceptance and product identification ................................... 9
3.1 Incoming acceptance .................................................................... 9
3.2 Product identification ................................................................... 9
3.3 Scope of delivery ...................................................................... 10
4 Installation ...................................................................... 11
4.1 Mounting conditions ................................................................... 11
4.2 Mounting the measuring device ...........................................................12
4.3 Post-installation check ................................................................. 15
5 Electrical connection ............................................................ 16
5.1 Connecting the measuring device ......................................................... 16
5.2 Connecting the sensors ................................................................. 23
5.3 Connecting additional inputs, outputs or relays ............................................... 27
5.4 Connecting PROFIBUS or Modbus 485 ...................................................... 30
5.5 Hardware settings ..................................................................... 34
5.6 Ensuring the degree of protection ......................................................... 35
5.7 Post-connection check ..................................................................36
6 Operation options ............................................................... 37
6.1 Overview ........................................................................... 37
6.2 Access to the operating menu via the local display ............................................. 38
7 Commissioning .................................................................. 39
7.1 Function check ....................................................................... 39
7.2 Switching on ......................................................................... 39
7.3 Basic setup .......................................................................... 40
About this document Liquiline CM442/CM444/CM448
4 Endress+Hauser
1 About this document
1.1 Warnings
Structure of information Meaning
LDANGER
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation will result in a fatal or serious injury.
LWARNING
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation can result in a fatal or serious injury.
LCAUTION
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid this situation can result in minor or more serious injuries.
NOTICE
Cause/situation
If necessary, Consequences of non-
compliance (if applicable)
‣Action/note
This symbol alerts you to situations which may result in damage to property.
1.2 Symbols
Symbol Meaning
Additional information, tips
Permitted or recommended
Not permitted or not recommended
Reference to device documentation
Reference to page
Reference to graphic
Result of a step
Liquiline CM442/CM444/CM448 About this document
Endress+Hauser 5
1.3 Symbols on the device
Symbol Meaning
Reference to device documentation
1.4 Documentation
The following instructions complement these Brief Operating Instructions and are available on
the product pages on the Internet:
• Operating Instructions Liquiline CM44x, BA00444C
• Device description
• Commissioning
• Operation
• Software description (excluding sensor menus; these are described in a separate manual -
see below)
• Device-specific diagnostics and troubleshooting
• Maintenance
• Repair and spare parts
• Accessories
• Technical data
• Operating Instructions Memosens, BA01245C
• Software description for Memosens inputs
• Calibration of Memosens sensors
• Sensor-specific diagnostics and troubleshooting
• Operating Instructions for HART communication, BA00486C
• Onsite settings and installation instructions for HART
• Description of HART driver
• Guidelines for communication via fieldbus and web server
• HART, SD01187C
• PROFIBUS, SD01188C
• Modbus, SD01189C
• Web server, SD01190C
• EtherNet/IP, SD01293C
• PROFINET, SD02490C
• Safety instructions for electrical apparatus in explosion-hazardous areas
• ATEX & IECEx, XA02419C
• CSA, XA02420C
Basic safety instructions Liquiline CM442/CM444/CM448
6 Endress+Hauser
2 Basic safety instructions
2.1 Requirements for personnel
• Installation, commissioning, operation and maintenance of the measuring system may be
carried out only by specially trained technical personnel.
• The technical personnel must be authorized by the plant operator to carry out the specified
activities.
• The electrical connection may be performed only by an electrical technician.
• The technical personnel must have read and understood these Operating Instructions and
must follow the instructions contained therein.
• Faults at the measuring point may only be rectified by authorized and specially trained
personnel.
Repairs not described in the Operating Instructions provided must be carried out only
directly at the manufacturer's site or by the service organization.
2.2 Designated use
2.2.1 Non-hazardous atmosphere
Liquiline CM44x is a multichannel controller for connecting digital sensors with Memosens
technology in non-hazardous environments.
The device is designed for use in the following applications:
• Water and wastewater
• Power stations
• Chemical industry
• Other industrial applications
2.2.2 Hazardous environment in accordance with cCSAus Class I Div. 2
‣Please pay attention to the control drawing and specified operating conditions in the
appendix of the Operating Instructions and follow the instructions.
2.2.3 Transmitter in non-explosion-hazardous environment with sensor
communication module 2DS Ex-i for sensors in explosion-hazardous
environment
The installation conditions in these Brief Operating Instructions and the corresponding XA
must be observed.
• ATEX & IECEx: XA02419C
• CSA: XA02420C
2.2.4 Non-designated use
Use of the device for any purpose other than that described, poses a threat to the safety of
people and of the entire measuring system and is therefore not permitted.
The manufacturer is not liable for damage caused by improper or non-designated use.
Liquiline CM442/CM444/CM448 Basic safety instructions
Endress+Hauser 7
2.3 Workplace safety
As the user, you are responsible for complying with the following safety conditions:
• Installation guidelines
• Local standards and regulations
• Regulations for explosion protection
Electromagnetic compatibility
• The product has been tested for electromagnetic compatibility in accordance with the
applicable international standards for industrial applications.
• The electromagnetic compatibility indicated applies only to a product that has been
connected in accordance with these Operating Instructions.
2.4 Operational safety
Before commissioning the entire measuring point:
1. Verify that all connections are correct.
2. Ensure that electrical cables and hose connections are undamaged.
3. Do not operate damaged products, and protect them against unintentional operation.
4. Label damaged products as defective.
During operation:
‣If faults cannot be rectified:
products must be taken out of service and protected against unintentional operation.
LCAUTION
Cleaning not switched off during calibration or maintenance activities
Risk of injury due to medium or cleaning agent!
‣If a cleaning system is connected, switch it off before removing a sensor from the medium.
‣If you wish to check the cleaning function and have therefore not switched off the cleaning
system, wear protective clothing, goggles and gloves or take other appropriate measures.
2.5 Product safety
2.5.1 State-of-the-art technology
The product is designed to meet state-of-the-art safety requirements, has been tested, and
left the factory in a condition in which it is safe to operate. The relevant regulations and
international standards have been observed.
2.5.2 IT security
We only provide a warranty if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any
inadvertent changes to the device settings.
Basic safety instructions Liquiline CM442/CM444/CM448
8 Endress+Hauser
IT security measures in line with operators' security standards and designed to provide
additional protection for the device and device data transfer must be implemented by the
operators themselves.
Liquiline CM442/CM444/CM448 Incoming acceptance and product identification
Endress+Hauser 9
3 Incoming acceptance and product identification
3.1 Incoming acceptance
1. Verify that the packaging is undamaged.
Notify the supplier of any damage to the packaging.
Keep the damaged packaging until the issue has been resolved.
2. Verify that the contents are undamaged.
Notify the supplier of any damage to the delivery contents.
Keep the damaged goods until the issue has been resolved.
3. Check that the delivery is complete and nothing is missing.
Compare the shipping documents with your order.
4. Pack the product for storage and transportation in such a way that it is protected
against impact and moisture.
The original packaging offers the best protection.
Make sure to comply with the permitted ambient conditions.
If you have any questions, please contact your supplier or your local Sales Center.
3.2 Product identification
3.2.1 Nameplate
Nameplates can be found:
• on the outside of the housing
• on the packaging (adhesive label, portrait format)
• on the inside of the display cover
The nameplate provides you with the following information on your device:
• Manufacturer identification
• Order code
• Extended order code
• Serial number
• Firmware version
• Ambient and process conditions
• Input and output values
• Activation codes
• Safety information and warnings
• Ex marking on hazardous area versions
‣Compare the information on the nameplate with the order.
Incoming acceptance and product identification Liquiline CM442/CM444/CM448
10 Endress+Hauser
3.2.2 Product identification
Product page
www.endress.com/cm442
www.endress.com/cm444
www.endress.com/cm448
Interpreting the order code
The order code and serial number of your product can be found in the following locations:
• On the nameplate
• In the delivery papers
Obtaining information on the product
1. Go to www.endress.com.
2. Call up the site search (magnifying glass).
3. Enter a valid serial number.
4. Search.
The product structure is displayed in a popup window.
5. Click on the product image in the popup window.
A new window (Device Viewer) opens. All of the information relating to your
device is displayed in this window as well as the product documentation.
3.2.3 Manufacturer address
Endress+Hauser Conducta GmbH+Co. KG
Dieselstraße 24
D-70839 Gerlingen
3.3 Scope of delivery
The scope of delivery comprises:
• 1 multichannel controller in the version ordered
• 1 mounting plate
• 1 wiring label (attached at the factory to the inside of the display cover)
• 1 printed copy of the Brief Operating Instructions in the language ordered
• Disconnection element (pre-installed on hazardous area version type 2DS Ex-i)
‣If you have any queries:
Please contact your supplier or local sales center.
Otros manuales para Liquiline CM442
10
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Panel de control de Endress+Hauser
