Endon EL- 40068 PIR Manual de usuario

The Light pack contains:

Wall light with PIR detector (with integral photocell)

The following tools may be required:

Selection of cross and flat head screwdrivers.

Electric drill and assorted drill bits.

Wire strippers.

Electrical insulation tape.

INSTRUCTION MANUAL

This product is only suitable for connection to a 240V~50Hz supply.

It is recommended that this wall light is installed by a qualified electrician in accordance with current IEE

Wiring Regulations and local Building Regulations and is for the Domestic environment only.

The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp miniature

circuit breaker).

This light has an IP44 (splash proof) rating suitable for use outdoors.

The detection range (angle / distance) and optimum mounting height is shown here. Use this information

before you choose a mounting position. Do not mount where the PIR can be activated by heat sources such as

central heating vents, animals, traffic etc.

Run supply wire from a 5-amp electrical supply using double insulated 3-core cable of type H05RN-F 1.0mm2

(not supplied) to selected site, ensuring it is adequately protected through the full length of the cable run, it

must come out of the mounting surface in line with the entry to the fitting.

Except where installed in a conduit or duct , which provides equivalent protection against mechanical damage,

a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for use as a

protective conductor, or be of insulated concentric construction. Buried cables shall be marked by cable

covers or a suitable marking tape. Buried conduits and ducts shall be suitably identified. Buried cables,

conduits and ducts shall be at a sufficient depth to avoid being damaged by any reasonably foreseeable

disturbance of the ground.

This product contains breakable parts – be careful during handling and maintenance to avoid breakage.

This light fitting uses none-replaceable LED`s.

We recommend that you do not stare directly into the light beam (of the LED`s).

If any part of the (LED) housing is broken or cracked then it cannot be replaced and the fitting must not be

used - as the water ingress protection has been compromised.

IMPORTANT: To achieve maximum corrosion resistance the surface of the Stainless Steel must be kept clean.

Surface contamination and the formation of deposits are critical factors which may lead to drastically reduced

life. An example is salt deposits from marine conditions. Washing with soap or a mild detergent and warm

water followed by a clean water rinse and finally wiping dry is usually adequate for most S/S items used in the

domestic environment.

If any modification is made it will invalidate the warranty and may render the product unsafe.

Before you start

Please read these instructions carefully before fitting your new light and retain for reference.

Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker

before commencing installation.

Ensure that no one else has access that would enable the supply to be inadvertently reconnected.

Check the packaging and make sure that you have all the required parts.

Follow each assembly step in order to prevent incorrect assembly

Make sure all screws / nuts, including electrical connections etc are fully tightened before use.

DO NOT CONNECT THIS PRODUCT TO A DIMMER SWITCH.

EL- 40068 PIR - Outdoor PIR wall fitting.

Safety Warnings

Endon Lighting

LS9 0SE

20150922

These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.

Assembly / user instructions

N210 104

Diagram A

Diagram B

Diagram C

1. Determine the position of your light fitting

taking into account the optimum

mounting / detection height (2M). Make

sure there is sufficient cable coming out

of the wall to connect to the terminal

block. Ensure that the mounting surface

is solid, preferably a brick or block wall

and ensure that there are no other cables

or pipes beneath the surface.

2. Diagram A. Fit the 2 threaded posts in

the back plate and bring the mains cable

through the rubber grommet then use the

back plate as a template and mark the 2

fixings holes, making sure the back plate

is the correct way up and the threaded

bolts are horizontal. Use appropriate

fixings to secure the back plate to the

wall.

3. Diagram B. Connect the house wiring to

the internal terminal block. The cable

entry grommet and the back plate seal

must be securely in place to ensure that

the water ingress protection is

maintained. NOTE: This is a Class I

fitting and must be earthed. Connect

the incoming mains as per the diagram

4. Diagram C. Fit the terminal block onto

the post in the back plate and then fit the

front frame over the 2 threaded bolts in

the back plate. Secure with the 2

threaded nuts / clear washers. Take care

not to trap or strain the internal cables..

5. To Test the Lantern. Turn on the

power. To test the PIR unit in daylight,

turn both the timer dial (TIME) and the

Sensitivity dial (SENS) gently fully anti-

clockwise with the blade of a small screw

driver. Activate the PIR by covering the

PIR lens with your hand. The unit will

light and should stay on for

approximately 5-15 seconds then go off.

It will remain off until the light level drops.

6. To adjust Time On. By adjusting the

TIME dial the unit will stay on (once

activated) from 5 -15 seconds (fully anti-

clockwise) to 3 -5 minutes (Fully

clockwise).

7. To adjust sensitivity – detection

distance.By adjusting the SENS dial the

detection distance can be changed –

minimum detection is fully anticlockwise -

or maximum detection distance is dial

turned fully clockwise.

NOTE:-

1. All time on values are approximate.

2. At initial power-on activation, the

lantern will switch on and may remain

on for up to 2 minutes. Keep out of the

way of the activation zone and once

the light goes off make the setting

adjustments.

Threaded posts

Fixing screws

Grommet

Threaded nuts

Tabla de contenidos

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario