Encore Networks BANDIT Manual de usuario

encor en

•etworksTM

Broadband Access Network Device for Intelligent Termination (BANDIT), BANDIT II, BANDIT III, BANDIT IP,

BANDIT Mini, BANDIT Plus, Encore Legacy-to-IP Operating System (ELIOS), FastCONNECT, IP Banking

Router 10 (IBR-10), IP Legacy Router 100 (ILR-100), Remote Data Unit (RDU), Selective Layer Encryption (SLE),

Virtual Broadband Redundancy System (VBRS), VPN Satellite Router 30 (VSR-30), and VPN Satellite Router 1200

(VSR-1200) are trademarks of Encore Networks, Inc. All other trademarks are the properties of their respective owners.

See the BANDIT Products Software Configuration and Maintenance Guide for statements on Product Warranties

and on Limitation of Liability.

BANDIT™, BANDIT IP™, and BANDIT

Plus™ Installation Guide

for ELIOS™ Software Version 0600

his guide presents procedures for a standard installation of the Broadband Access Network

Device for Intelligent Termination™ (BANDIT™).

Note: Except where otherwise specified, this document’s procedures apply to the following

models of the BANDIT™ chassis: the original BANDIT™, the BANDIT IP™, and the

BANDIT Plus™. In addition, the screens shown in this document are examples; the choices

shown on your BANDIT’s menus depend on the features in the chassis and on the software

version installed in the device. (For figures, tables, and configurations not addressed in this

Installation Guide, see the BANDIT Products Software Configuration and Maintenance Guide or the

BANDIT Products Hardware Reference Guide.)

Gather all required information. Before you start these procedures, make sure you have all the

information required to set up the BANDIT for use in your network—for example:

• The device’s IP address

•Thedevice’spasswords

• The device’s VPN configuration, if any

• Interface requirements for the device’s ports

• Interface types for the ports—for example, DTE or DCE

• Interface protocols for the ports

• Network and routing functions that the device will perform

• Other pertinent network information

Use the site planning worksheets in the BANDIT Products Software Configuration and Maintenance

Guide as checklists for this information.

If you have questions or concerns after you have followed these procedures, contact Encore

Networks, Inc., at support@encorenetworks.com, 703-787-4625 (fax), or 703-318-4350 (voice).

Revision I.2, April 2009

Document Part Number 14973.1001

2BANDIT™, BANDIT IP™, and BANDIT Plus™ Installation Guide

A Plug-and-Play Mode

The BANDIT IP comes as a plug-and-play device so that it can be up and running quickly in

standard installations. (The other products in the BANDIT family come with factory default

settings. If you wish, you can change any unit to plug-and-play mode, save the

configuration, and restart the unit.)

In plug-and-play mode, a BANDIT product is a DHCP client on the WAN (internet) port,

and is a DHCP server on the LAN (intranet) port. When a BANDIT powers up in plug-and-

play mode, it is assigned its public IP address by the WAN's DHCP server. (Typically, the

WAN's DHCP server is a device maintained by your internet service provider, or ISP.) Then

the BANDIT product, as the local DHCP server, assigns private IP addresses to DHCP clients

on the local network. (The BANDIT’s DHCP server has a default IP address pool, which can

be changed.)

Warning: If your network already has a DHCP server, disable the BANDIT IP's plug-

and-play mode before you connectthe BANDIT IP to the network. Otherwise, there will

be contention between the DHCP servers.

A.1 Using Plug-and-Play Mode

To use the BANDIT IP’s plug-and-play features, do the following:

1Follow the instructions for installing the hardware, as described in Section B, Setting Up

the Hardware.

2Boot up the BANDIT, as described in Section D, Logging In.

Note: After logging in, you may wish to review the LAN port's settings. See Section F.3.2,

DHCP Settings.

A.2 Disabling Plug-and-Play Mode

To disable the BANDIT IP’s plug-and-play features, do the following:

1Follow the instructions for installing the hardware (but do not connect the BANDIT

ports to the network devices). See Section B, Setting Up the Hardware.

2Then boot up the BANDIT device. See Section D, Logging In.

3In the Main Menu, select Load Factory Defaults. Then select Write, then Reset. See the

following sections:

•Section E, Using the Main Menu

•Section G, Saving (Writing) the Device’s Configuration

•Section H, Restarting (Resetting) the Device

4After the device restarts, select Typical Configurations. See Section E, Using the Main

Menu.

5In the Typical Configurations menu, select the LAN port and review its settings. See

Section F.3, Ports.

BANDIT™, BANDIT IP™, and BANDIT Plus™ Installation Guide 3

6When you have verified that the device’s default factory configuration matches your

needs (or when you have changed the configuration as needed), save the configuration.

See the following sections:

•Section F, Configuring the Software

•Section G, Saving (Writing) the Device’s Configuration

7Connect the BANDIT's WAN and LAN ports to the networks.

8Then connect the BANDIT’s modem port, serial port, and expansion port to the devices

the BANDIT will use.

9Reset the BANDIT, as described in Section H, Restarting (Resetting) the Device.

10 If, at any time, you wish to exit the BANDIT session, see Section I, Exiting a Session.

B Setting Up the Hardware

The BANDIT is available in the following models: the original BANDIT, the BANDIT IP, and

the BANDIT Plus. (For information on product models, see the BANDIT Products Hardware

Reference Guide.)

1Unpack the chassis and components from the shipping box. Make sure you have all the

parts:

• the chassis (Figure 1 through Figure 3)

• an autosensing external power supply (only for the BANDIT IP or the original

BANDIT)

• an RJ-45 Supervisory cable

• an adapter for the Supervisory cable (described in the Note in Step 9)

• an RJ-11 modem cable (only for the original BANDIT or the BANDIT Plus)

• a paper copy of this Installation Guide

• any additional accessories that you ordered

Note: Shipments within North America include a power cable for an AC outlet. For

shipments outside North America, contact your distributor for a cable that meets local

requirements to connect the BANDIT’s power supply to a power outlet.

Note: If you wish to view or download the customer documentation for the BANDIT

products, visit the following site:

www.encorenetworks.com/support/documentation/voice_data/broadband.htm

Contact your Encore Networks sales representative if you wish to order a CD

containing BANDIT documentation.

Figure 1. Original BANDIT Chassis, Front

4BANDIT™, BANDIT IP™, and BANDIT Plus™ Installation Guide

Figure 2. BANDIT IP Chassis, Front

Figure 3. BANDIT Plus Chassis, Front

2Do one of the following:

aPlace the original BANDIT or BANDIT IP chassis on a tabletop or shelf.

bMount the BANDIT Plus chassis in an equipment rack.

3Connect an earth ground wire to the chassis, as follows: Attach a (minimum) 12 AWG

wire to the earth ground screw (next to the safety ground symbol), on the extreme right

rear or extreme left rear of the chassis (Figure 4 through Figure 6). Use a ring terminal,

such as an AMP (part number 36160), for this connection.

Warning: An earth ground must connect to the chassis so that the device remains

grounded even when it is not receiving power.

Figure 4. Original BANDIT Chassis, Rear

Figure 5. BANDIT IP Chassis, Rear

BANDIT™, BANDIT IP™, and BANDIT Plus™ Installation Guide 5

Figure 6. BANDIT Plus Chassis, Rear

4If this is a BANDIT Plus, and if it uses a Remote Data Unit™ (RDU, Figure 7), connect

the BANDIT Plus’s Ethernet LAN port (Figure 6) to the RDU’s Ethernet port (Figure 8).

Figure 7. Remote Data Unit, Front

Figure 8. Remote Data Unit, Rear

5Connect the BANDIT’s ports to their network devices. For example, on the original

BANDIT, connect the LAN port, WAN port, modem port, serial port, and expansion

port to the network devices.

Warning: Do not connect the ports to the network devices if you need to disable the

BANDIT IP’s plug-and-play mode.

6If an RDU is connected to the BANDIT Plus, connect the RDU’s serial ports to their

network devices.

7If you are setting up the BANDIT IP or the original BANDIT: Connect the chassis to the

external power supply.

8Do one of the following:

aFor the BANDIT IP or original BANDIT: Connect the external power supply to an outlet

supplying 100–240 VAC at 47–63 Hz.

bFor the BANDIT Plus: Connect the chassis to an outlet supplying 100–240 VAC at 47–

63 Hz.

9Use the Supervisory cable and adapter to connect the device’s Supervisory port to your

PC’s COM port.

6BANDIT™, BANDIT IP™, and BANDIT Plus™ Installation Guide

Note: An eight-pin modular (RJ-45) to DB-9 adapter is the standard adapter to connect

the Supervisory cable to a PC. This adapter is shipped with the unit. The following

alternate adapters are also available. (Contact Encore Networks, Inc., if you need either

of these adapters.)

• An RJ-45 to DB-25 adapter for connection to most asynchronous terminals

• An RJ-45 to DB-25 modem adapter to connect a modem, for out-of-band management

or remote configuration

10 If you need to disable the BANDIT IP’s plug-and-play mode, see Section A.2, Disabling

Plug-and-Play Mode. Then connect the BANDIT IP’s ports to their network devices.

C Wireless Support

If you ordered a CDMA or GSM wireless card with the BANDIT device, you need to set up

the card for use in the carrier network. And, if you wish to change the default settings for

wireless access, you need to reconfigure the wireless port.

In addition, a GSM wireless card must hold the appropriate Subscriber Identity Module

(SIM) for access to the carrier’s GSM wireless network.

To configure the BANDIT device for wireless use, see the BANDIT Products Wireless Access

Guide.

D Logging In

1On the PC, open a terminal-emulation session, such as HyperTerminal. Use the settings

in Table 1 to establish communication between the terminal console and the BANDIT.

2On the terminal console, press Enter to connect to the attached device.

❖After successful log-in, the Main Menu appears.

Table 1. Supervisory Port Communication Settings

Parameter Value

Bits per second 9600

Data bits 8

Parity None

Stop bit 1

Flow control Hardware

BANDIT™, BANDIT IP™, and BANDIT Plus™ Installation Guide 7

E Using the Main Menu

The Main Menu is displayed when you log onto the BANDIT. From the Main Menu, you can

configure and operate the BANDIT.

Note: Whenever you wish to return to a higher level in the BANDIT menus, press

Escape.

Caution: The Supervisory connection to the device will time out after five (5) minutes

of console inactivity. If you have changed the device’s configuration and wish to use the

new configuration, save (write) the configuration before you leave the console. (See

Section G, Saving (Writing) the Device’s Configuration.)

1On the Main Menu, do one of the following:

aTo disable the BANDIT IP’s plug-and-play mode, select Load Factory Defaults.

❖The BANDIT’s settings for plug-and-play mode are replaced by a configuration that

you can customize for your site. Perform the procedures in Section G, Saving (Writing)

the Device’s Configuration, and Section H, Restarting (Resetting) the Device. Then select

Step 1bor Step 1cin this current procedure.

bTo set up a basic configuration of the BANDIT for your network, select QuickStart

Config Builders.

❖The Startup Config Options menu is displayed. (On the next menu—the Startup

Configuration Scenarios menu—you can enter basic information; the BANDIT will use

this information to build a standard configuration.) The Banking configuration is used

for financial networks. Select Satellite if most of the transmissions will travel over

satellite networks. For other networks, use Generic. Go to Section F.1, Startup

Configuration.

Main Menu

----------

1) QuickStart Config Builder

2) Typical Configurations

3) Advanced Configurations

4) Tools

V) View Current Unit Status

L) Load Factory Defaults

P) Load Plug and Play Defaults

W) Write Configuration

R) Reset Unit

X) eXit Session

S) Statistics

Y) sYstem Administration

Enter Choice :

8BANDIT™, BANDIT IP™, and BANDIT Plus™ Installation Guide

cTo configure specific features, select Advanced Configurations.

❖The Advanced Configurations menu is displayed. You configure most parameters of

the BANDIT from this menu. Go to Section F, Configuring the Software.

F Configuring the Software

For a standard, basic configuration of the BANDIT for your network, see Section F.1, Startup

Configuration. For configuration of specific features, see the following sections.

•Section F.1, Startup Configuration

•Section F.2, Device Addresses

•Section F.3, Ports

•Section F.4, Virtual Private Network Connections

•Section F.5, IP Configuration

•Section F.6, Simple Network Management Protocol

F.1 Startup Configuration

The menu provides several templates for configurations that your network may use. You can

select a template (also known as a startup scenario), change the scenario’s IP addresses and

related information to reflect the values in your network, and load the scenario into the

BANDIT.

Note: If you want the device to keep the configured scenario, be sure to write (save) the

configuration and reset the device.

To configure a basic setup for this device in your network, do the following:

1On the Main Menu, select QuickStart Config Builders.

Startup Config Options

-----------------------

1) GENERIC

2) BANKING

Enter Choice :

Advanced Configurations

------------------------

1) Physical Configurations

2) Data Configurations

3) Local Address

4) Routing

5) Global Paths

Enter Choice :

BANDIT™, BANDIT IP™, and BANDIT Plus™ Installation Guide 9

2On the Startup Config Options menu, select the Generic set of configuration templates.

❖The menu for Startup Configuration Scenarios appears.

3Select one of the listed set-ups.

❖The menu for the selected set-up (scenario) is displayed. (The menu shown is for a

PPPoE WAN VPN Gateway, Initiator.)

Note: At this point, all IP addresses, etc., have null values. Before you can load the

configuration into the BANDIT, you must enter values that reflect your network’s

settings.

BANDIT

Startup Configuration Scenarios

---------------------------------------

1) PPPoE WAN Router

2) PPPoE WAN VPN Gateway(Initiator)

3) PPPoE WAN VPN Gateway(Initiator) With Dial Backup

4) PPPoE WAN VPN Gateway(Terminator)

5) PPPoE WAN VPN Gateway(Terminator) With Dial Backup

6) Ethernet WAN Router

7) Ethernet WAN VPN Gateway(Initiator)

8) Ethernet WAN VPN Gateway(Initiator) With Dial Backup

9) Ethernet WAN VPN Gateway(Terminator)

A) Ethernet WAN VPN Gateway(Terminator) With Dial Backup

Enter Choice :

Startup Configuration Parameters

---------------------------------

1) System Name :

2) LAN Interface IP : 0.0.0.0 /0.0.0.0

3) LAN Private NAT IP : 0.0.0.0 /0.0.0.0 masq:0.0.0.0

4) WAN Interface IP : Dynamic

5) PPPoE User Name :

6) PPPoE Password :

7) Primary DNS Server : 0.0.0.0

8) VPN Gateway :

9) VPN User ID :

A) VPN Pre-Shared Key :

B) Remote Subnet : 0.0.0.0/0.0.0.0

L) Load Above Config

R) Reset (Load, Write and Reset)

Z) Clear All Fields

Enter Choice :

10 BANDIT™, BANDIT IP™, and BANDIT Plus™ Installation Guide

4For each item (parameter) in the menu, do the following:

aSelect the item (for example, WAN Interface IP).

bType a value for the item, and press Enter.

cIf the item requests additional information, enter that information.

❖When the item has been configured, the scenario’s menu is displayed again.

5After you have performed Step 4 for each item (parameter) in the menu, do one of the

following:

aSelect Load Above Config.

❖The following prompt asks for confirmation. Go to Step 6.

bSelect Reset (Load, Write and Reset).

❖The following prompt asks for confirmation. Go to Step 6.

cSelect Clear All Fields.

❖The following prompt asks for confirmation.

• Do one of the following:

◆If you wish to reconfigure, enter Y.

❖All fields in the menu are reset to null values. Return to Step 4.

◆If you do not wish to reconfigure, press Escape to return to the Startup

Configuration Scenarios menu.

❖The configuration retains the settings you have entered, but they are not yet in use.

Return to Step 4.

Enter IP Address :

Caution: Existing configurations will be over written

Do you want to Continue?(Y/N)[N]:

Caution: Existing configurations will be over written

Do you want to Continue?(Y/N)[N]:

This Clears All the above Fields, Continue?(Y/N)[N]:

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Accesorios de red de otras marcas

Valcom

Valcom VIP-804 Manual de usuario

SKUTCH

SKUTCH BA-1000 Manual del producto

QUNDIS

QUNDIS RNN5 Manual de usuario

Asus

Asus AAEON FWS-2365 Manual de usuario

Sophos

Sophos XG 85w Manual de usuario

AMCI

AMCI RBE2-8 Manual de usuario

Patton electronics

Patton electronics 2888 Manual de usuario

Cradlepoint

Cradlepoint COR IBR1100/IBR1150 Manual de usuario

Paradyne

Paradyne Hotwire 8620 Manual de usuario

Infra Cool

Infra Cool F-1.3 Manual de usuario

Edgewater Networks

Edgewater Networks 4300T Manual de usuario

Edimax

Edimax SB-2200g Manual de usuario

Extreme Networks

Extreme Networks Mogul-100 Manual de usuario

Aaeon

Aaeon FWS-8500 Manual de usuario

Panduit

Panduit Z11C Series Manual de usuario

F5 BIG-IP 10000 Series Instrucciones de montaje

ZyXEL Communications

ZyXEL Communications NMA1115 Manual de usuario

Auerswald

Auerswald COMtrexx Business Manual de usuario