Emulex LP850 Manual de usuario

LightPulse LP850 Fibre Channel PCI Host Adapter Manuals Page 1of 10

Prerequisites:

lOne open 32-bit or 64-bit PCI bus slot with a 3.3 VDC or 5.0 VDC signaling interface

lMaximum PCI bus clock rate of 33 MHz

lMedia and connectors (user supplied; view supported media types.)

Follow these procedures to assemble and install the host adapter. Click procedures for

details. When finished, click "Return to top of page" to return to this summary.

1.Record reference numbers. Write down the host adapter's IEEE address and serial

number.

2.Install the host adapter board. Insert the host adapter board into a PCI slot on the

computer's motherboard.

3.Attach media. Connect fiber optic or copper duplex cabling to the host adapter.

4.Apply power. Apply power to the computer and observe the LED display.

After the host adapter is installed, install device drivers or run a DOS diagnostic program to

check host adapter functions or update firmware.

Record reference numbers

Each host adapter is shipped with a unique address identifier called the IEEE address. The

Fibre Channel industry uses a World Wide Name (WWN) derived from the IEEE address,

and this number is need for arbitrated loop connectivity. The serial number is used when

communicating with Emulex. Both numbers are clearly marked on the board. We

recommend that you record these numbers before installation.

Return to top of page.

Install the host adapter board

1.Turn off and unplug the computer.

2.Remove the computer case.

3.Remove the blank panel from an empty 32 or 64-bit PCI bus slot.

4.Insert host adapter board into the empty 32 or 64-bit PCI bus slot. Press firmly until

seated.

5.Secure the host adapter's mounting bracket to the case with the panel screw.

LightPulse LP850 Fibre Channel PCI Host Adapter Manuals Page 2of 10

6.Replace the computer case and tighten case screws.

The host adapter is now installed in the PC. Continue with the attach media section.

Return to top of page.

Attach media

Select one of these types of media supported by the Emulex host adapter:

lMultimode fiber optic cable (50/125 µm or 62.5/125 µm)

lCopper duplex cable

If necessary, use an MIA to connect fiber optic cabling to a host adapter's copper DB9

connector.

Return to top of page.

Fiber optic cable (multimode)

More Information: View fiber optic specifications.

These cables support a data rate of 1.0625 Gb/s for short wave and long wave lasers.

Fiber Optic Cable Maximum

Length Minimum

Length Connector

62.5/125 µm

(multimode) 175 meters 2 meters Dual SC

50/125 µm

(multimode) 500 meters 2 meters Dual SC

9/125 µm (single

mode) 10,000 meters 2 meters Dual SC

1.Connect the fiber optic cable to the dual SC connector on the host adapter board as

shown below.

To attach fiber optic cable to a host adapter's copper DB9 connector, use an MIA.

LightPulse LP850 Fibre Channel PCI Host Adapter Manuals Page 3of 10

2.Connect other end of cable to Fibre Channel device.

After the media is connected to the host adapter, you are ready to apply power to the

computer.

Return to top of page.

Copper duplex cable

TechNote: View copper specifications.

Cable Type Maximum

Length Data Rate Connector

Dual Twinax

or Quad Axial 30 meters 1.0625 Gb/s DB9

1.Connect the copper duplex cable to the DB9 connector on the host adapter board as

shown below.

LightPulse LP850 Fibre Channel PCI Host Adapter Manuals Page 4of 10

2.Connect other end of cable to Fibre Channel device.

After the media is connected to the host adapter, you are ready to apply power to the

computer.

Return to top of page.

Apply Power

1.Verify the host adapter is securely installed in the computer.

2.Verify correct media is attached.

3.Plug in and turn on computer.

4.Observe LEDs for Power On Self Test (POST) results.

Return to top of page.

Power On Self Test and LEDs

Green and yellow display lights (LEDs) can be seen through openings in the host adapter's

mounting bracket. Green indicates power and yellow signifies port activity.

This chart shows normal LED indications. For other LED patterns, refer to the detailed LED

chart.

Green LED Yellow

LED State

OFF flashing

(irregular) POST processing in progress

ON blink normal - active - link up

blink OFF normal - link down or not yet started

Host adapter installation is complete. At this point, you should install a driver or run the

DOS diagnostic utility. Return to index to choose.

Return to top of page.

LightPulse LP850 Fibre Channel PCI Host Adapter Manuals Page 5of 10

LP850 Additional Information

LP850 Host Adapter Specifications

Parameter Range

Hardware Interface 20 pin connector for GBIC models

Physical Dimensions Short PCI form factor 6.88" x 4.20"

Power Requirements 11 watts @ + 5.0 VDC (typical)

Airflow 100 lfm minimum

Temperature Operating: 32° to 113°F (0° to 45°C)

Storage: 14° to 131°F (-10° to 55°C)

Humidity 5% to 95% non-condensing

Agency Approvals for

LP850-D1

UL recognized to UL1950

CUR recognized to CSA22.2, No. 950

TUV certified to EN60950

FCC Rules, Part 15, Class A

Industry Canada, ICES-003, Class A

EMC Directive 89/336/EEC (CE Mark)

EN55022, Class A

EN50082-1

Australian EMC Framework (C-Tick Mark)

AS/NZS 3548:1994, Class A

VCCI, Class A.

Agency Approvals for

LP850-N1/T1

and LP850-F1

Class 1 Laser Product per DHHS 21CFR (J) & EN60825

UL recognized to UL1950

CUR recognized to CSA22.2, No.950

TUV certified to EN60950

FCC Rules, Part 15, Class B

Industry Canada, ICES-003, Class B

EMC Directive 89/336/EEC (CE Mark)

EN55022, Class B

EN50082-1

Australian EMC Framework (C-Tick Mark)

AS/NZS 3548:1994, Class B

VCCI, Class B

MIA

A Media Interface Adapter (MIA) is an adapter that allows you to convert from fibre optic

cable to copper. The adapter has two signal interfaces: an optical interface (SC connector)

and a serial interface (DB9 connector). By connecting an MIA to a copper DB9 connector on

a host adapter, a non-Open Fiber Control (non-OFC) optical link is provided. The Emulex

host adapter with a copper interface is designed to support an MIA that conforms with the

Fibre Channel - Media Interface Adapter specification.

LightPulse LP850 Fibre Channel PCI Host Adapter Manuals Page 6of 10

Note An MIA is user supplied.

To attach an MIA,

1.Connect the MIA DB9 connector to the host adapter copper

DB9 connector.

2.Tighten screws carefully - do not over tighten.

3.Connect the SC connector of the fiber optic cabling to the

optical SC port of the MIA.

For more information on MIA specifications and operating instructions, consult the MIA

manufacturer’s documentation.

Supported media types

lMultimode fiber optic cable (50/125 µm or 62.5/125 µm) with dual SC connectors,

used with short wave lasers

lCopper duplex cabling with DB9 connectors (also called DE9)

lMedia Interface Adapter (MIA) used to convert from fiber optic to copper, if required

(user supplied)

Host Adapter LEDs

POST conditions and results are summarized in this table.

Green LED Yellow

LED State

OFF OFF wake-up failure (dead board)

OFF ON POST failure (dead board)

OFF slow

blink (1

Hz) wake-up failure

OFF fast blink

(4 Hz) failure in POST

OFF flashing

(irregular) POST processing in progress

LightPulse LP850 Fibre Channel PCI Host Adapter Manuals Page 7of 10

ON OFF failure while functioning

ON ON failure while functioning

ON slow

blink (1

Hz) normal - inactive

ON flashing

(irregular) normal - active

ON fast blink

(4 Hz) normal - busy

slow blink OFF normal - link down or not yet started

slow blink slow

blink (1

Hz) off-line for download

slow blink fast blink

(4 Hz) restricted off-line mode (waiting for restart)

FCC and Regulatory Notices

Class 1 Information Label

CLASS 1 LASER PRODUCT

LASER KLASSE 1

LUOKAN 1 LASERLAITE

APPAREIL A` LASER DE CLASSE 1

TO IEC 825-1 (1993) + CENELEC HD 482 S1

The above statement applies to products marketed in the European Union.

FCC and VCCI

Model LP850-D1 (Copper Model)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

LightPulse LP850 Fibre Channel PCI Host Adapter Manuals Page 8of 10

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the interference at his own

expense. Shielded cables must be used between this equipment and attached peripheral devices. The reader is

cautioned that changes or modifications made to the equipment not expressly approved by Emulex could void

the user’s authority to operate this equipment.

The above statement applies to products marketed in the USA

This class A digital apparatus meets all requirements of the Canadian Interference - Causing Equipment

Regulations. Cet Appareil numerique de la classe A respecte toutes les exigences du reglement sur le material

brouilleur du Canada.

The above statement applies to products marketed in Canada.

FCC Compliance Information Statement; Models LP850-T1/N1 (GBIC Models)

FCC Compliance Information Statement; Model LP850-F1 (1 X 9)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Responsible Party: Paul Folino, President & CEO, Emulex Corporation, 3535 Harbor Blvd., Costa Mesa, CA

92626, USA, (714) 662-5600

LightPulse LP850 Fibre Channel PCI Host Adapter Manuals Page 9of 10

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

lReorient or relocate the receiving antenna.

lIncrease the separation between the equipment and receiver.

lConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.

lConsult the dealer or an experienced radio/TV technician for help.

The reader is cautioned that any changes or modifications to the equipment not expressly approved by Emulex

could void the user’s authority to operate this equipment.

This class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment

Regulations. Cet Appareil numerique de la classe B respecte toutes les exigences du reglement sur le material

brouilleur du Canada.

The above statement applies to products marketed in Canada.

VCCI Notices and Translations (Japan Only)

Note VCCI regulations provide that changes or modifications

not expressly approved by Emulex Corporation could

void your authority to operate this equipment.

Models LP850-T1/N1 (GBIC Models)

This is a Class B product based on the standard of the Voluntary Control Council for Interference by

Information Technology Equipment (VCCI). If this equipment is used near a radio or television receiver in a

domestic environment, it may cause radio interference. Install and use the equipment according to the

instruction manual.

Model LP850-D1 (Embedded Copper Model)

Product Label

LightPulse LP850 Fibre Channel PCI Host Adapter Manuals Page 10 of 10

Translation:

This is a Class A product. In a domestic environment this product may cause radio interference in which case

the user may be required to take adequate measures. VCCI—A

Manual Notice

Translation:

This is a Class A product based on the standard of the Voluntary Control Council for Interference by

Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio

disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

Tabla de contenidos

Otros manuales de Tarjeta PCI de Emulex

Emulex

Emulex LP8000 Manual de instalación y funcionamiento

Manuales populares de Tarjeta PCI de otras marcas

ERMA

ERMA SSI 1417 Manual de usuario

SIIG

SIIG CyberSerial Dual PCI Instrucciones de montaje

Moxa Technologies

Moxa Technologies CP-102E Manual de usuario

I-Bus

I-Bus IBC2602 Manual de usuario

Exsys

Exsys EX-60102 Manual de usuario

Chelsio Communications

Chelsio Communications T5 Series Manual de usuario

Conrad Electronic

Conrad Electronic 97 46 71 Manual de usuario

Micro Innovations

Micro Innovations USB650A Manual de usuario

KTI Networks

KTI Networks KF-310 Manual de usuario

Asus

Asus SpaceLink WL230 Manual de usuario

SIIG

SIIG SC2475 Manual de usuario

TRENDnet

TRENDnet TEW-703PI Manual de usuario

Belkin

Belkin F5D7000F Manual de usuario

Pericom

Pericom PI7C7100 Manual de usuario

ADLINK Technology

ADLINK Technology cPCI-3548 Manual de usuario

Digium

Digium TE200 Series Manual de usuario

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manual de usuario

Western Digital

Western Digital FireWire PCI Adapter Manual de usuario