Empower ElektroBank14 Guía del usuario

Page 1 of 20

ElektroBank14 Installer Manual

Empower Energy Pty Ltd

Unit 23, 10-18 Orchard Rd

Brookvale, NSW, 2100

Australia

Page 2 of 20

AMENDMENT RECORD

Issue Number

Date

Description

DRAFT A

29th Sept 2020

Initial Issue

DRAFT B

31st Oct 2020

Include IEC62619 requirements

Associated / Referenced documents

Document number /

Revision number

Date

Document title

Page 3 of 20 
 
Table of Contents 
 
TABLE OF CONTENTS.......................................................................................................3 
MARKINGS & SYMBOLS....................................................................................................4 
1 Battery Markings............................................................................................................................5 
EXTERNAL RCD REQUIREMENTS...................................................................................6 
MOUNTING THE UNIT.........................................................................................................6 
1 Wall Mount ....................................................................................................................................7 
2 Floor Mount ...................................................................................................................................8 
3 Battery Installation.........................................................................................................................8 
WIRING ..............................................................................................................................12 
1 Port Locations ..............................................................................................................................12 
2 Grid Port Including Protective Earthing .......................................................................................12 
3 Backup Port..................................................................................................................................13 
4 PV Ports........................................................................................................................................14 
5 DRM0............................................................................................................................................14 
6 Ethernet .......................................................................................................................................14 
7 Meter Connections.......................................................................................................................15 
8 Commissioning.............................................................................................................................15 
MAINTENANCE.................................................................................................................18 
1 User Maintenance........................................................................................................................18 
2 Trained Service Professional Maintenance..................................................................................18 
WARNINGS........................................................................................................................19 
ELECTRICAL RATINGS....................................................................................................20 
 

Page 4 of 20

2Markings & Symbols

1. To identify the location where the operator's manual is stored or to identify

information that relates to the operating instructions. To indicate that the operating

instructions should be considered when operating the device or control close to

where the symbol is placed.

2. To identify equipment that has risk of electric shock.

3. To identify energy storage timed discharge –that is the time required after

disconnecting the unit from all energy sources and turning off the battery

circuit breaker until the energy storage in the unit is less than50VDC.

4. To indicate that caution is necessary when operating the device or control close to

where the symbol is placed, or to indicate that the current situation needs operator

awareness or operator action in order to avoid undesirable consequences.

5. To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective

earth (ground) electrode.

Page 5 of 20

2.1 Battery Markings

Battery Type

Secondary (rechargeable) Li or Li-ion

Cell Designation

IFpP/34/201/173/M/-10+40/90

Module Designation

IFpP34/201/173[8S]M/-10+40/90

Battery System Designation

IFpP34/201/173[48S]M/-10+40/90

System Capacity

100Ah

Nominal Voltage

153.6V

Watt-hour

15.36kWh

Caution Statement

WARNING! A battery can present a risk of electrical shock,

fire, or explostion from vented gases. Observe proper

precautions.

Dispsoal

Electronic Device: Do not throw away

Proper diposal of batteries is required. Refer to

your local codes for disposal requirements.

Recommended Charge

instrucitons

Charging is only allowed using the provided Elektrobank

system, do not try charging with a different charger

Page 6 of 20

This product requires an external RCD Type B to be installed on the backup

port (if used), external to the product. It needs to be a combined MCB/RCD

Type B and rated to 20A and 30mA respectively.

Installation shall follow and comply with AS 5139, AS 3000 as well as any

requirements from this manual.

3External RCD Requirements

4Mounting the Unit

1. Find a suitable mounting location as per AS 5139

•a risk assessment for the mounting location shall be completed

2. The Elektrobank can be mounted on a wall with the wall mount kit or floor mounted with the

floor mount kit.

3. Mounting Location

•Don’t mount the Elektrobank14 in a location with direct sunlight.

•Ensure no animals or insects are likely to be able to nest close to the unit.

•Ensure there are no obstructions inside the dimensions from Figure1

•Installation position shall not prevent access to disconnection means.

•No plants can be growing inside 1m radius from the mounting location

0.6m minimum

0.3m minimum 0.3m minimum

1.5m minimum

0.3m minimum

Figure 1 - Clearance around unit

Page 7 of 20

4.1 Wall Mount:

1. Conform to AS 5139 requirements

2. Ensure the wall is vertical and flat across the full width and height of theElekbtrobank14

3. Ensure the wall is structurally sound to take theweight of the Elektrobank14

4. Remove external packaging and remove wall mount bracket frompackaging.

5. Mount wall bracket on wall

•Use spirit level to ensure bracket is level

•Use screws/anchor bolts suitable for the material, each screw/bolt shall have a ratingof

>100kg and be of suitable length to secure the unit safely.

•A minimum of 12 screws/bolts shall be used, 4, at each level, as per the diagram

•If fixing into a wooden wall, at least six screws shall be fixed into one structural vertical

timbers and another 6 screws into a second vertical timber, these are normally spaced

600mm apart, the wall bracket has been designed to span thiswidth.

Figure 2 - Wall Mount Bracket Fixing Locations

6. Using a two man lift, place the Elektrobank onto the wallbracket

7. Fix the small top fixing bracket with the 2x supplied M6screws

Page 8 of 20

Figure 3 - Top Fixing Bracket

4.2 Floor Mount

1. Floor Mounting is suitable when the wall is considered not completely structurally sound to

mount the unit, this could be the case for many types of wooden structures or walls with

plastic/wooden cladding.

2. Floor Mounting is only viable when there is a suitable vertical structural member or wall to fix

the top of the unit to. The unit cannot be mounted freestanding.

3. Floor mounting can only take place on a flat concrete base with dimensions at least 2mx1m with

a minimum thickness of 100mm. But a separate risk assessment shall be carried out to ensure

the platform is structurally sound to mount the unit to.

4. Fit the base unit to the unit using the provided M6 bolts andwashers

5. Position the unit in the desired position and mark the 4 mounting hole locations on the concrete

base

6. Remove the unit, drill the holes into the concrete, fit anchor bolts (100kg rating minimum) and

attach the unit

7. Attach the unit to the wall using the attached wall tie bracket. Ensure this wall tie bracket it

firmly fixed to a structural member –use a bespoke load bearing brace if required.

4.3 Battery Installation

1. Before starting ensure the enclosure is securely fixed (wall mounted or floor mounted) as per

above instructions.

2. Ensure all Circuit breakers are off and the unit is completely isolated from mains andPV

Page 9 of 20

Figure 4: Unit before installing batteries

3. Fit the battery modules in the below order, ensuring not to trap any wires behind each module

and to fix the module before fitting the next module, using the long M6 bolts provided, tighten

to approximately 1N.m

a. ASYH006 - bottom left

b. ASYH007 –bottom right

c. ASYH004 –middle left

d. ASYH005 –middle right

e. ASYH002 –top left

f. ASYH003 –top right

4. Tighten all of the 24 mounting bolts to 12N.m +/-1N.m

5. Connect all the modules together, starting at the bottom LH blue connector and workingup

Page 10 of 20

Figure 5 - Module Connections

8. Next, connect the 6x BMS connectors, ensuring to connect the right size into the correct

receptacle and again working from the bottom up

Figure 6 - BMS Connections

Otros manuales para ElektroBank14

Tabla de contenidos

Manuales populares de Accesorios para cámaras de otras marcas

Viltrox

Viltrox EF-NEX Instrucciones de instalación

Calumet

Calumet 7100 Series CK7114 Manual de usuario

Ropox

Ropox 4Single Series Manual de usuario

Cambo

Cambo Wide DS Digital Series Instrucciones de funcionamiento

Samsung

Samsung SHG-120 Manual de usuario

Ryobi

Ryobi BPL-1820 Manual de operación

Aegis

Aegis ABL-36020P Manual de usuario

Pentax

Pentax Data Back Fc Manual de usuario

Fantasea

Fantasea EyeGrabber F Series Manual de usuario

Honeywell

Honeywell HDZ20HD Manual de usuario

EGO

EGO BA1400T Manual de usuario

Sima

Sima SRW-62 Manual de usuario

Shape

Shape A7SSMKIT Manual de usuario

Slide Kamera

Slide Kamera HST-2 Manual de usuario

Power works

Power works 2902613 Manual de usuario

SES

SES SE-2047-2 Manual de usuario

Olympus

Olympus PT-EP05L Manual de usuario

Starlite

Starlite OctoDome nxt Manual de usuario