Empire Comfort Systems VFP36FB0F-3 Guía de inicio rápido

Page 1

INSTALLATION INSTRUCTIONS

AND OWNER'S MANUAL

The Breckenridge

Premium Vent-Free Universal Firebox

DO NOT ATTEMPT TO MODIFY OR ALTER THE

CONSTRUCTION OF THE FIREBOX OR ITS COMPO-

NENTS. ANY MODIFICATION OR ALTERATION OF

CONSTRUCTION MAY VOID THE WARRANTY OF

THIS FIREBOX.

CHILDREN AND ADULTS SHOULD BE ALERTED TO

THE HAZARDS OF HIGH SURFACE TEMPERATURE

AND SHOULD STAY AWAY TO AVOID BURNS OR

CLOTHING IGNITION.

YOUNG CHILDREN SHOULD BE CAREFULLY SU-

PERVISED WHEN THEY ARE IN THE SAME ROOM AS

THE FIREBOX.

FOR USE ONLY WITH A LISTED GAS-FIRED UN-

VENTED DECORATIVE ROOM HEATER NOT TO

EXCEED 40,000 BTU/H.

DO NOT BUILD A WOOD FIRE.

UNIVERSAL FIREBOX FOR ALL

VENT-FREE LOG SETS

MODEL

VFP36FB0F-3

WARNING: Improper installation, adjustment, alteration,

service or maintenance can cause injury or property dam-

age. Refer to this manual. For assistance or additional infor-

mation, consult a qualied installer, service agency or the

gas supplier.

Carefully review the instructions supplied with the decora-

tive type unvented room heater for the minimum replace

size requirement.

DO NOT INSTALL A VENT-FREE LOG SET IN THIS

FIREBOX, UNLESS THIS FIREBOX MEETS THE

MINIMUM DIMENSIONS REQUIRED FOR THE

INSTALLATION.

GAS-FIRED

ANSI Z21.91 Ventless Fireplace Enclosures for Gas Fired

Decorative Type Unvented Room Heaters

— Do not store or use gasoline or other ammable vapors

and liquids in the vicinity of this or any other appli-

ance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

WARNING: If the information in these instructions are

not followed exactly, a re or explosion may result caus-

ing property damage, personal injury or loss of life.

Installer: Leave this manual with the appliance.

Consumer: Retain this manual for future reference.

EMPIRE

Comfor t Systems

27136-0-0110Page 2

SECTION PAGE

Important Safety Information.................................................................................................3

Introduction ............................................................................................................................3

Clearances ..............................................................................................................................4

Firebox Installation Instructions......................................................................................... 5-7

Installing Hood................................................................................................................... 7-8

Gas Line Connection .............................................................................................................8

Optional Fresh Air Kit Installation Instructions ............................................................... 9-11

Optional Single Speed Blower Installations Instructions............................................... 12-14

Junction Box Wiring Installation Instructions......................................................................15

Maintenance .........................................................................................................................15

Parts List .............................................................................................................................16

Parts View.............................................................................................................................17

Accessories..................................................................................................................... 18-19

Master Parts Distributor List ................................................................................................20

How To Order Repair Parts ..................................................................................................20

Service Notes.................................................................................................................. 21-23

TABLE OF CONTENTS

27136-0-0110 Page 3

The installation must conform with local codes or, in

the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1 (latest edition) and to the National

electrical Code, ANSI/NFPA70 (latest edition).

NOTE: Installation and repair should be done by a quali-

ed service person. The appliance should be inspected

before use and at least annually by a qualied service

person. More frequent cleaning may be required due to

excessive lint from carpeting, bedding material, etc. It

is imperative that control compartment, burners and

circulating air passageways of the appliance be kept

clean.

Any safety screen or guard removed for servicing an

appliance must be replaced prior to operating the ap-

pliance. Provide adequate combustion and ventilation

air.

The ow of combustion and ventilation air MUST NOT

be obstructed.

Provide adequate clearance around air openings into

the combustion chamber and adequate accessibility

clearance for servicing and proper operation. NEVER

obstruct the front opening of the appliance.

This Empire Comfort Systems, Inc. firebox and its

components have been tested and will operate safely when

installed in accordance with this installation manual.

Read all instructions before starting installation, then

follow these instructions carefully during installation

to maximize rebox benet and safety. Report to your

dealer any parts damaged in shipment.

The Empire Comfort Systems, Inc. warranty will be

voided by, and Empire Comfort Systems, Inc. disclaims

any responsibility for the following actions:

- Installation of any damaged rebox.

- Modication of the rebox or any of the components

parts thereof.

- Installation other than as instructed by Empire

Comfort Systems, Inc.

- Installation and/or use of any component part or

accessory not approved by Empire Comfort Systems,

Inc. in combination or assembly with a Empire

Comfort Systems, Inc. rebox, not withstanding any

independent testing laboratory or other third party

approval of such component part or accessory.

Any such action may create a possible re hazard.

Consult your local building codes.

Firebox Screen.

The rebox screen must be in place when the rebox is

operating.

Instructions to Installer

1. Installer must leave instruction manual with owner after

installation.

2. Installer must have owner ll out and mail warranty card

suppliedwithrebox.

3. Installer should show owner how to start and operate log set

thatisinstalledintorebox.

Important

All correspondence should refer to complete Model Number,

Serial Number.

Notice:Duringinitialringofthisreboxwithalogsetinstalled,its

paint will bake out, and smoke will occur. To prevent triggering of

smoke alarms, ventilate the room in which the unit is installed.

Qualied Installing Agency

Installation and replacement of gas piping, gas utilization

equipment or accessories and repair and servicing of equipment

shallbeperformedonlybyaqualiedagency.Theterm"qualied

agency" means any individual, rm, corporation or company

which either in person or through a representative is engaged in

and is responsible for (a) the installation or replacement of gas

piping or (b) the connection, installation, repair or servicing of

equipment, who is experienced in such work, familiar with all

precautions required and has complied with all the requirements

of the authority having jurisdiction.

State of Massachusetts: The installation must be made by

a licensed plumber or gas tter in the Commonwealth of

Massachusetts. The state of Massachusetts requires that a

exible appliance connector cannot exceed three feet in

length.

Sellersofunventedpropaneornaturalgas-redsupplemental

room heaters shall provide to each purchaser a copy of 527

CMR 30 upon sale of the unit.

In the State of Massachusetts, unvented propane and natural

gas-redspaceheatersshallbeprohibitedinbedroomsand

bathrooms.

The installation must conform with local codes or, in the absence

of local codes, with the National Fuel Gas Code, ANSI Z223.1/

NFPA 54.*

*Available from the American National Standards Institute, Inc., 11 West

42nd St., New York, N.Y. 10036.

IMPORTANT SAFETY INFORMATION

INTRODUCTION

27136-0-0110Page 4

Sidewall Clearances:Theclearancefromtheinsideoftherebox

to perpendicular combustible side wall should not be less than

6".See Figure 1.

Firebox Side and Back Clearances:Thereboxoutercasingside

andbackangesarezeroclearancetocombustibles.

Top Framing and Finishing: Combustible framing may rest on

topofstandoffs.Combustiblenishingmaterialsmayextend

to the top standoff screws on the front edge of the outer wrap.

See Figure 2.

Ceiling Clearances:Theceilingheightshouldnotbelessthan42"

from the top of the hood. See Figures 3a and 3b.

Mantel Clearances: Ventfreereboxmodelsmustusethehood

supplied with the rebox, or one of the optional hood kits

available for each model. If a combustible mantel is installed,

it must meet the clearance requirements detailed below.

Grate Clearance: The minimum clearance between the front legs

ofthegrateandfrontedgeofthereboxis2".

Leaveatleast36"clearancefromthefrontoftherebox.

CLEARANCES

45°

6”

3”

MAX.

PERPENDICULAR

SIDE WALL

FRONT FACE (SIDE)

FIREBOX

(TOP VIEW)

COMBUSTIBLE

MATERIALS ALLOWED

IN SHADED AREAS

FIREBOX

STAND OFF

FINISH WITH TRIM KIT OR

NON-COMBUSTIBLE MATERIAL

AS DESIRED.

COMBUSTIBLE

FINISHED WALL

OR MANTEL

2X4

HEADER

MANTEL

STANDARD

HOOD

13”

10”

12”

MAX

42”

MIN.

(CEILING TO

TOPOF HOOD)

11 1/2”

MIN.

FIREBOX

FACE

84”

MIN.

(CEILING TO FLOOR)

CEILING

COMBUSTIBLES

ALLOWED

3/8” COMBUSTIBLE

CLEARANCE REQUIRED

FROM TOP EDGE

OF FIREBOX

10”

22”

8”

20”

6½”

18”

5”

16”

3½”

14”

2”

12 ½”

3/4”

24 ½”

0”

Figure 1 Figure 2

Figure 3a - Mantel Clearances with Standard Hood Figure 3b - Mantel Clearances with Optional Extended Hood

MANTEL

EXTENDED HOOD

(VB4H SERIES)

10”

12”

MAX

42”

MIN.

(CEILING TO

TOPOF HOOD)

8”

MIN.

FIREBOX

FACE

84”

MIN.

(CEILING TO FLOOR)

CEILING

COMBUSTIBLES

ALLOWED

3/8” COMBUSTIBLE

CLEARANCE REQUIRED

FROM TOP EDGE

OF FIREBOX

10”

22”

8”

20”

6½”

18”

5”

16”

3½”

14 ½”

2½”

24 ½”

0”

16 ½”

27136-0-0110 Page 5

Premium Vent-Free Firebox Framing Dimensions (in inches)

"A" "B" "C"

Model Framing Height Framing Width Framing Depth

VFP36FB 411/2" 40" 21"

Attention:Add3-3/4"to"A"Dimensionwhenusingushmantel

base.

Framing dimension A includes a three inch clearance for stand-

offs on rebox.

Any vent-free Gas Log Heater must be “For use with approved

ANSI Z21.11.2 unvented room heater.”

Follow and complete the installation instructions of the gas log set

andtherequirementsofthisrebox.

Checkallttingsforleaksbeforelightingthegaslogset.

In planning the installation for the rebox, it is necessary to

determine where the unit is to be installed and whether optional

accessories are desired. Gas supply piping should also be planned

at this time.

A gas shut off must be in this line.

Thereboxcanbemountedonanyofthesesurfaces:

1. Aathardcombustibleornon-combustiblesurface.

2. A raised platform of combustible or non-combustible

material.

3. Recessed into the floor as illustrated by Figure 4 (flush

face).

4. Supportedunderall(4)cornersofthereboxsothatcontact

is made on all four perimeter edges on the bottom of the unit

(Example: Four (4) concrete masonry blocks).

If the firebox is installed directly on carpeting, tile or other

combustiblematerialotherthanwoodooring,itshouldbeinstalled

on a metal or wood panel extending the full width and depth of

the unit.

At this point, you should have decided what components to include

inyourinstallation,andwherethereboxistobelocated.Ifthis

has not been done, stop and consult your dealer for assistance with

this planning.

Planning Your Installation

Please note that the optional BVA1 Fresh Air kit available for use

with the Vent Free Firebox must be installed at the time of the initial

installation. Refer to pages 9, 10, and 11 for detailed instructions

for the air kit.

Accessory kits such as the FBB5 Blower kit, Trim kits, Mantles,

Full Cabinet Mantels, plus other Decorative Frame, Hood, and

Dooraccessorykitsmaybeinstalledafterthereboxissecured

to the framed opening.

Refer to the instructions provided with each of the optional

accessory kits for proper installation and operation.

Firebox Framing

Firebox framing can be built before or after the rebox is set

in place. Framing should be positioned to accommodate wall

coveringandreboxfacingmaterial.Thereboxframingshould

be constructed of 2 x 4 lumber or heavier. The framing headers may

restonthetopofthereboxstandoffs.RefertoFigures 6 and 7

forreboxframingdimensions.

COMBUSTIBLE MATERIALS ALLOWED

NON-COMBUSTIBLE

FINISHING MATERIAL

TO FIREBOX OPENING

Figure 4

Figure 5

FIREBOX INSTALLATION INSTRUCTIONS

27136-0-0110Page 6

Figure 6

Firebox Dimensions

FIREBOX INSTALLATION INSTRUCTIONS (continued)

VFP36

A41 1/8”

B39 1/2”

C21 7/16”

D32 1/4”

E38 1/2”

F36”

G27 13/16”

H6 1/8”

I34”

J8 3/8”

K5 5/8”

L37 1/2”

M74 13/16”

27136-0-0110 Page 7

Locating Firebox

Placereboxinframingopening.Usethefour(4)framingbrackets

providedonthereboxtoattachreboxtoframing.Differenthole

locationscanbeusedfornishingmaterialswiththicknessesof

3/8",1/2"and3/4".Attachthesematerialswithscrewsprovided,

two (2) per framing bracket. See Figure 7.

Framingbracketsshouldtdirectlyagainstframingmaterial.Use

at least one (1) nail per bracket to secure in place.

Checksquarenessofthereboxpriortosecuringtoframedopening.

See Figure 8.

Figure 7

Ablackhoodthatisfurnishedwitheachrebox(oroptionalhood)

MUSTbeinstalledbeforethereboxisused.Failuretodosomay

createapossiblerehazard.Thehoodislocatedinsidetherebox.

If brass, stainless steel, or hammered pewter hoods are desired,

they can be purchased as an option. Attachment is the same as the

standard black hood.

1. Loosenthetwoscrews(A)holdingreboxtoptofacepanel,

thenslidethehoodangebetweenthereboxtopandfacepanel

and re-tighten the screws.

2. Install one (1) screw at each end of the hood as shown (C).

Caution: The hood must be installed prior to operation of appliance.

See Figure 9

AT TACH (4)

FRAMING BRACKETS

TO SIDES OF FIREBOX

PRIOR TO INSTALLING

UNIT TO FRAMED OPENING

ACAC

Figure 9

FIREBOX OPENING

CHECK TO SEE

THAT BOX IS SQUARE

PRIOR TO ATTACHING TO

FRAMING

Figure 8

FIREBOX INSTALLATION INSTRUCTIONS (continued)

INSTALLING HOOD

27136-0-0110Page 8

Thereboxisdesignedtoaccepta3/8-inchgaslineforanapproved

vent-freegaslogset.Havethelineinstalledbyaqualiedservice

person in accordance with all building codes. Consult local building

codes to properly size the gas supply line leading to the 3/8-inch

hook-up at the unit. The state of Massachusetts requires that a

exibleapplianceconnectorcannotexceedthreefeetinlength.

Gasaccessholesareprovidedonbothsidesoftherebox.See

Figure 10.

Check gas type. Use only the gas type indicated on the gas log

set rating plate. If the gas listed on the plate is not your type of

gas supply, DO NOT INSTALL. Contact your dealer for proper

model.

AlwaysuseanexternalregulatorforallLPreboxestoreducethe

supplytankpressuretoamaximumof14"w.c.Thisisinaddition

totheregulatorttedtothelogset.

WA R N I N G : C O N N E C T I O N D I R E C T LY T O A N

UNREGULATED L.P. TANK CAN CAUSE EXPLOSION.

InstallonlyaANSIZ21.11.2vent-freelogsetintothisrebox. Figure 10

Extended Hoods

Ifyournon-combustiblefacingmaterialisover1"inthicknessthatwillbeusedtonishthisrebox,anextendedhoodisavailablethat

willextendout2"fartheroutintotheroom.Contactyourlocaldealerfordetails.

Finishing

Alljoints(top,bottomandsides),wherethewallordecorativefacingmaterialmeetsthereboxsurroundshouldbesealedwithanon-

combustible material.

Hearthextensionsarerecommended,butnotrequiredforthesereboxes.

VB4H36BL Standard Black

VB4H36BR Polished Brass

VB4H36SS Stainless Steel

VB4H36HP Hammered Pewter

GAS ACCESS HOLES

INSTALLING HOOD (continued)

GAS LINE CONNECTION

27136-0-0110 Page 9

OPTIONAL FRESH AIR KIT INSTALLATION INSTRUCTIONS

FOR DELUXE AND PREMIUM FIREBOXES

4. Next, with the vise grip attached, feed the long control rod

through the small rectangular opening at the left side of the

reboxface.Carefullypositiontherodandbracketsothat

thebracketcanbesecuredtotheinsideopeningoftherebox

with two screws. See Figure 14. Do not remove vise grips at

this time.

5. Working from the side cutout opening, place the slightly

opened air door assembly into the cutout opening as shown

in Figure 15.

6. While holding the door assembly in your left hand, grasp the

vise grip (attached to the long control rod). Rotate and move

the control rod around until the inside end of the rod is mated

The optional BVA1 Fresh Air Kit is designed to introduce outside

airtothereplaceorreboxasdesired.

Itmustbeinstalledpriorto,oratthetimeofreplaceorrebox

installation to framing.

The Fresh Air kit must be installed prior to the installation of wall-

boardorothernishingmaterialsaroundtheunit.

Tools needed: Gloves, Metal snips, Vise-Grip, ¼” Nut Driver,

Standard Screwdriver

Caution: Sharp edges

Air Door Installation for Vent Free Firebox Models:

VFP(32,36,42)FB

1. Begin by removing the rectangular cutout located on the left

sideoftherebox.Useglovesandsheetmetalsnipstocre-

ate the opening for the Air Door assembly to install into. See

Figures 13 and 14.

2. Movethelefthandcurtainscreentothecenteroftherebox

opening.

3. Grasp the long control rod lever with control bracket (items 7

and 8 in Fresh Air Kit Parts List) securely with a vise grips

as shown in Figure 13.

Figure 11

Figure 13

Figure 14

Figure 15

TO INSTALL BVA-1 FRESH AIR KIT

REMOVE RECTANGULAR CUT-OUTWITH

SHEET META L CUTTERS

Figure 12

27136-0-0110Page 10

withtheholeinthefrontangeofthemovableairdoor.See

Figure 16.

7. Once the control rod is fed through the air door hole, gently

lift the outer air door plate assembly inward and upward until

the mounting holes in the plate line up with the pilot holes in

the side wrap.

8. Install (4) screws to retain the Air Door assembly. See Fig-

ure 18.

9. Remove vise grip from control rod, then check the operation

of the Air Door. The control lever should open the air door

Figure 16

Figure 19

OUTSIDE AIR

ROD BRACKET

OPEN

FRESH AIR ROD

(CONTROL LEVER)

LEFT SIDE VIEW

OF FIREBOX OPENING

TOP CUTAWAY

VIEW

DAMPER

ASSEMBLY

OUTER

CASING

FRESH AIR

ROD

OUTSIDE AIR

ROD BRACKET

Figure 18

OUTSIDE AIR

ROD BRACKET

OPEN

FRESH AIR ROD

(CONTROL LEVER)

LEFT SIDE VIEW

OF FIREBOX OPENING

TOP CUTAWAY

VIEW

DAMPER

ASSEMBLY

OUTER

CASING

FRESH AIR

ROD

OUTSIDE AIR

ROD BRACKET

when rotated upward, and can be locked open by pulling for-

ward into the notch at the top of the control lever bracket.

10. To close, simply disengage by letting the lever rotate down-

ward. The air door will remain closed by magnetic action.

See Figure 19.

Figure 17

FRESH AIR KIT PARTS LIST

INDEX

NO.

PART

NO. DESCRIPTION

QUANTITY

SUPPLIED

1 10124 OUTSIDE AIR HOOD 1

2 18476 OUTSIDE AIR TUBE ASSEMBLY 1

3 R8196 WASHER, SILICONE (BV) 1

4 19548 DAMPER ASSEMBLY 1

5 R8047 TUBULAR CLIP (BV) 1

6 R8189 ROD, FRESH AIR (BV) 1

7 R8703 ROD, AIR CONTROL (FB) 1

8 20473 BRACKET, OUTSIDE AIR ROD (FB) 1

Tabla de contenidos

Otros manuales de Chimenea de interior de Empire Comfort Systems

Empire Comfort Systems

Empire Comfort Systems DVCT35CBN95N-1 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems Boulevard MULTIFUNCTION REMOTE DVLL60BP90N-2 Manual de usuario

Empire Comfort Systems

Empire Comfort Systems White Mountain Hearth DVCX36FP91K-3 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems AV36MTEKN-1 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems DVP FP3 4 Series Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems DVCT36CBP95N-1 Guía de planificación

Empire Comfort Systems

Empire Comfort Systems MILLIVOLT VFPA32BP30LN-1 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems VF24FP2-1 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems FG28BMK(N Manual de usuario

Empire Comfort Systems

Empire Comfort Systems HYDRAULIC Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems vfp36pp32EN-2vfp36pp32Ep-2 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems Mantis Series Manual de usuario

Empire Comfort Systems

Empire Comfort Systems Tahoe DVP36FP30-4NAT Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems VFD20MS30N-1 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems FG28BM Series Manual de usuario

Empire Comfort Systems

Empire Comfort Systems VFLL38FP30LN-1 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems VFPC20IN73N-2 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems DVLT42FP92N-2 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems DVP20MS Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems VFLL48SP(3 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems OP36FP32MN-3 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems MILLIVOLT DVCP36SP30N-1 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems DXL30IN91N-2 Guía de inicio rápido

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación