Emerson SolaHD SDU 500A Manual de usuario

SDU AC-A Series

A272-290

Rev. 5 07/2018

Uninterruptible Power Supply

SDU AC-A Series

A272-290 Rev. 5 07/2018

Page: B

What’s Included

The SDU UPS is shipped with the following items:

•User manual

•UPSMON software CD

NOTE: Monitoring/diagnostic software is included on the UPSMON CD. The software is compatible

with Windows XP, 7, 8, 10, Server-2000, 2003, 2008 and Linux.

•PSMON High speed 2.0 Standard Type A-B USB cable, 6 ft (1.8 m)

•One SDUCOMMCVR the SDU AC-A Series communication slot cover.

•One warning label. (Refer to Installation Instructions, Item 6).

Accessories (Optional)

• SDU-PMBRK: Mounting brackets to secure the UPS to the wall, back of the panel or enclosure

• SDUEDC: Side Mount Enhanced DIN Rail Clip

• SDUCFRELAYCARD: Dry contact relay status with LED diagnostics and standby Mode capability

(Please refer to SDU A-Series COMM Cards Manual)

• SDUENETIPCARD: Network communication module is a high performance communication solution for

industrialelddevices.ItisdesignedforusewithhighperformancenetworkssuchasrealtimeEthernet

and synchronized applications such as servo drive systems (Please refer to SDU A-Series COMM Cards

Manual)

SDU AC-A Series

A272-290 Rev. 5 07/2018

Page: C

CONTENTS

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . 1

2.0 Important Safety Instructions . . . . . . . . . . . . . . 2

3.0 Installation Instructions . . . . . . . . . . . . . . . . . 3

4.0 Specifications . . . . . . . . . . . . . . . . . . . . . . 5

5.0 General Description . . . . . . . . . . . . . . . . . . . 6

6.0 System Block Diagram . . . . . . . . . . . . . . . . . 8

7.0 Operating Instructions . . . . . . . . . . . . . . . . . 9

8.0 Diagnostics . . . . . . . . . . . . . . . . . . . . . . 11

9.0 Battery Back-Up Times . . . . . . . . . . . . . . . . 12

10.0 Software and Interface . . . . . . . . . . . . . . . 13

11.0 Storage . . . . . . . . . . . . . . . . . . . . . . . 14

SDU AC-A Series

A272-290 Rev. 5 07/2018

Page: D

FIGURES

Figure 1: Transition to Back-Up Mode Due to Power Outage . 1

Figure 2: Input/Output Terminals . . . . . . . . . . . . . . 3

Figure 3: Mounting the UPS DIN Rail . . . . . . . . . . . . . 3

Figure 4: Front Panel . . . . . . . . . . . . . . . . . . . . 6

Figure 5: Product Dimensions . . . . . . . . . . . . . . . . 7

Figure 6: SDU A-Series UPS System Block Diagram . . . . . . 8

Figure 7: UPS Control Panel, Configuration . . . . . . . . 10

Figure 8: Connecting UPS to Computer . . . . . . . . . . 13

Figure 9: UPSMON Control Panel, Monitor System . . . . . 13

TABLES

Table 1: Green Mode Setting Table. . . . . . . . . . . . . . 9

Table 2: Diagnostics LED/Alarms. . . . . . . . . . . . . . 11

Table 3: Battery Back-Up Time Chart. . . . . . . . . . . . 12

Page: 1

SDU AC-A Series

A272-290 Rev. 5 07/2018

1.0 Introduction

The SDU AC - A Series is a compact, “Off-Line” DIN rail mountable UPS, which provides conditioned power to

sensitive electronic equipment in an industrial environment. It supplies connected equipment with stepped

approximation to sinewave input during power outage to simulate the power generated by the utility.

Figure 1: Transition to Back-Up Mode Due to Power Outage

AC Mode AC Loss

of Power Battery Mode

Input voltage range is 80% to 110% (ideal protection for the critical connected loads). Battery charging occurs

automatically when ac power is applied, no need to switch ON the UPS. When power fails, the UPS can be

automatically turned OFF, as long as the connected loads are not operating to save the battery energy. The

SDU also includes an automatic self-test feature to test the UPS function and battery. If the battery is no longer

useful, the unit will sound an alarm and an LED indicator will illuminate

This SDU AC - A Series has a communication port that can accommodate an optional communication card.

Contact a SolaHD Technical Support representative for a list of currently available communication cards.

SDU AC-A Series

A272-290 Rev. 5 07/2018

Page: 2

2.0 Important Safety Instructions

2.1 Safety Precautions—SAVE THESE INSTRUCTIONS

This manual contains important safety instructions that should be followed during the installation of

the Uninterruptible Power Supply (UPS). Please read all safety, installation, and operating instructions

before attempting to install or operate the UPS. Follow all warnings on the unit and in this manual

during installation and operation.

• Topreventtheriskofreorelectricshock,installtheUPSinatemperatureandhumiditycontrolled

ventilatedenclosure,freeofconductivecontaminants,moisture,ﬂammableliquids,gases,andcorrosive

substances.

• To reduce the risk of electric shock, do not remove the cover, as it has no user-serviceable parts inside.

Somecomponentsarelive,evenwhenacpowerisdisconnected.Forservice,contactaqualied

technician.

• Although your UPS has been designed and manufactured to assure personal safety, improper use can

resultinelectricalshockorre.Toensuresafety,pleaseobservethefollowingrules:

• Turn OFF UPS and disconnect the ac supply before cleaning. Do not use liquid or aerosol cleaners.

A dry cloth is recommended to remove dust from the surface of your UPS.

• Do not install or operate the UPS in or near water.

• Do not place the UPS on an unstable cart, stand, or table.

• Do not place the UPS under direct sunlight or close to heat-emitting sources.

• To allow proper ventilation of the UPS, do not block or cover the top and bottom sides of the unit.

Do not insert any objects into the ventilation holes or other openings of the UPS. Keep all vents free of

dustaccumulationthatcouldrestrictairﬂow.

• Donotdisposeofbatteriesinare;theymayexplode.Donotopenordamagethebattery.Released

electrolyte is harmful to the skin and eyes and may be toxic.

• This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D, T3. When installed in a

hazardous location, adhere to the following:

!WARNING

• EXPLOSION HAZARD - Do not disconnect equipment unless power has been removed or the area is known

to be non-hazardous.

• EXPLOSION HAZARD - Batteries must only be replaced in an area known to be non-hazardous.

• EXPLOSION HAZARD - Do not reset circuit breaker unless power has been removed from the equipment or

the area is free of ignitible concentrations.

If your UPS demonstrates any of the following conditions, turn OFF the UPS, disconnect the ac supply

and contact your local distributor, SolaHD representative or SolaHD Technical Support at

1-800-377-4384.

• The circuit breaker opens frequently.

• The UPS does not operate in accordance with the user manual.

Page: 3

SDU AC-A Series

A272-290 Rev. 5 07/2018

3.0 Installation Instructions

!WARNING

To reduce risk of fire, connect only to a circuit provided with 20A maximum branch circuit overcurrent

protection in accordance with the NEC, ANSI/NFPA 70, and the CEC Part 1, C22.1.

Protective

Earth

Bottom

View

Protective

Earth

Neutral Neutral

Line Line

Figure 2: Input/Output Terminals

1. Placement:InstalltheUPSinaprotectedareawithadequateairﬂowandfreeofexcessivedust.

Do not operate the UPS outdoors. The products are suitable for a Pollution Degree 3 environment.

2. COMM CARD Installation: To install the optional card, remove the COMM PORT cover and insert the

card. Refer to the SDU COMM CARD Manual for more details. (Refer to inside cover for COMM CARD

options or contact your SolaHD representative).

3. DIN Rail Mounting: Follow instructions below.

A) Tilt unit as illustrated.

B) Put it onto the DIN rail.

C) Push downwards until stopped.

D) Push at the lower front edge to lock.

E) Shake the unit slightly to ensure that the unit

is secure.

F) Check if UPS is facing upright and not tilting

downward.

Figure 3: Mounting the UPS DIN Rail

SDU AC-A Series

A272-290 Rev. 5 07/2018

Page: 4

!WARNING

Risk of electric shock, disconnect AC main power source before wiring. Ensure proper grounding

4. I/O Wiring: Make sure the UPS and the AC Supply is OFF (disconnected) before installation. Wire the

UPS terminals with 90 °C rated copper wire according to the table below. Connect the AC input ground

terminal to the main supply ground. Connect line in neutral supply conductors. Connect the loads to the

output hardwire connector. Verify proper wiring connections then apply power to the UPS.

Reference Figure 2.

Wire Gauge 10-18 AWG

Screw Torque 9 lb-in. (101.7 N-cm)

5. Internal Battery: Charge the UPS battery for a minimum of 8 hours before initial use. The UPS charges

its battery whether the UPS is on or off, when it is connected to AC power.

6. Warning Label: Apply the provided electrical shock warning label to the panel, making it clearly visible

to the user.

Risk of electrical shock—

hazardous live parts inside this

panel may be energized from the

battery supply, even when the

input ac power is disconnected.

7. Do not connect Ground to Neutral on either input or output terminals of the UPS unit.

Page: 5

SDU AC-A Series

A272-290 Rev. 5 07/2018

4.0 Specifications

Description Catalog Number

SDU 500A SDU 850A SDU 500A-5 SDU 850A-5

INPUT

Capacity VA/Watts 500/300 850/510 500/300 850/510

Voltage Vac 120 V + 10%, -20% 230 V +/ -15%

Frequency 50 or 60 Hz, +/ -10% (auto-sensing)

Harmonic Distortion THD:42.1%;maximumsingleharmonicdistortionof:25.6%

OUTPUT (Back-Up Mode)

Voltage Vac Simulated sine wave

120 V +/-5% 230 V +/-5%

Frequency 50 or 60 Hz, +/-0.5% auto-sensing

Transfer Time Typical <8 ms

PROTECTION

Unit Input (internal) 10A 5A

Overload Protection UPSshutdownifoverloadexceeds105%ofnominalat20s,120%at10s,130%at3s;auto-recovery

Short Circuit UPS shutdown, auto-recovery

BATTERY

Type Sealed, maintenance-free, lead acid batteries

Typical Recharge

Time 8 hours

Back-Up Time

(at full load) 4 min. 2 min. 4 min. 2 min.

ALARM

ON Battery Slow beeping every 4 seconds

Battery Low Rapid beeping every second

Overload Continuous beeping sound

ENVIRONMENT

Ambient Operation 0–95% humidity, non-condensing. 50 °C up to 6,600 ft. (2000m)

Audible Noise <40 dBA (1 m from surface)

Vibration

Operating - IEC60068-2-6, Sine Wave: 10Hz to 500Hz @19.6m/S²,

displacement of 0.35mm, 60 min per axis for all X, Y, Z direction.

Non-operating-IEC60068-2-6,Random:5hzto500Hz(2.09Grms);20minperaxisforallX,Y,Z

Shock Operating - IEC60068-2-27, Half Sine Wave: 10G for a duration of 11ms, shock for 1 direction (X axis)

Non-operating - IEC60068-2-27, Half Sine Wave : 30G for duration of 11ms, 3 shocks for all 3 axes

WEIGHT & DIMENSIONS

Net Weight, lb. (kg) 10.6 (4.8) 11.5 (5.2) 10.6 (4.8) 11.5 (5.2)

H x W x D, in. (mm) 4.87 x 11.1 x 4.81 (123.7 x 281.9 x 122.3)

CERTIFICATIONS

Safety

: UL 1778, 5th Ed./CSA 107.3. UPS evaluated for use in UL 508/CSA 107.1 industrial applications

overvoltage category 3, pollution degree 3 with no output derating

: ISA 12.12.01/CSA 213 Class I, Div 2, Groups A, B, C, D, T3

CE;LowVoltageDirective-EN62040-1

EMC FCCPart15,SubpartB;EN62040-2;EN55032;EN55024-ClassA

SDU AC-A Series

A272-290 Rev. 5 07/2018

Page: 6

5.0 General Description











   



Communication Card Options

SDUCFRELAYCARD

SDUENETIPCARD

Figure 4: Front Panel

1. POWER ON/OFF/TEST:

ON - To turn the UPS ON, press and release the button for more than 2 seconds until you hear “3 quick

beeps” and the LEDs light. SELF-TEST - Press the button for less than one second to activate the self-testing.

OFF-PressformorethanvesecondstoturnOFFLED,UPSturnon.

2. Battery Warning/Overload Indicator (Red LED):

TheLEDﬂasheswhenthebatteryneedstoberechargedandtested.

The LED will illuminate when the unit is subjected to an overload condition.

If the unit shuts down due to overload, the LED and alarm will continue for two minutes.

3. ON Battery Indicator (Yellow LED): The LED illuminates when the UPS is supplying battery power to the

loads.

4. AC Input Normal Indicator (Green LED): The LED illuminates when the line input voltage is normal.

5. Input: IP20-rated Input Screw Terminals.

6. Output: IP20-rated Output Screw Terminals.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unión Postal Universal de Emerson

Emerson

Emerson Liebert NX Manual de usuario

Emerson

Emerson SolaHD SDU DC UPS B Series Manual de usuario

Emerson

Emerson Liebert itON BX Manual de usuario

Emerson

Emerson Series 610 Manual de usuario

Emerson

Emerson SDU AC Series Manual de usuario

Emerson

Emerson PSI-XR Manual de usuario

Emerson

Emerson SolaHD S4K2U-5C Series Manual de usuario

Emerson

Emerson Liebert APS Manual de usuario

Emerson

Emerson 10 kVA Manual de usuario

Emerson

Emerson Liebert NX 10-30kVA Manual de usuario

Emerson

Emerson LIEBERT NX 40-120KVA Manual de usuario

Emerson

Emerson Liebert GXT3-3000RT120 Manual de usuario

Emerson

Emerson SolaHD SDU AC B-Series Manual de usuario

Emerson

Emerson Liebert GXT4-5000RT230 Manual de usuario

Emerson

Emerson itON BX Manual de usuario

Emerson

Emerson Liebert GXT3 Series Manual de usuario

Emerson

Emerson Liebert GXT-MT Manual de usuario

Emerson

Emerson Liebert GXT4-700RT230 Manual de usuario

Emerson

Emerson Adapt Manual de usuario

Emerson

Emerson Liebert Nfinity 12-20kVA Manual de usuario

Emerson

Emerson Liebert NX Manual de usuario

Emerson

Emerson SolaHD S4K2UC Series Manual de usuario

Emerson

Emerson Liebert HiPulse E Series Manual de uso y cuidado

Emerson

Emerson Liebert itON 1500 Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario

ZincFive

ZincFive BC Series Manual de usuario