Emerson MRLDS-450 Manual de usuario

Document Part # 026-4417 Rev 1 Page 1 of 9

Visit our website at http://www.emerson.com for the latest technical documentation and updates.

The MRLDS-450 refrigerant gas detector is designed for use in refrigeration

applications and may be used as a stand-alone device, or connected to a facility’s

building management system (BMS). It enables compliance with refrigerant

safety codes (ASHRAE 15 and EN378) and features audible and visual alarms to

alert personnel in the event of a refrigerant leak.

1. Safety Instructions

DANGER: The MRLDS-450 is NOT certified or approved for operation in

oxygen-enriched atmospheres. Failure to comply may result in severe injury or

death.

WARNING: Use this product ONLY for the purposes and under the conditions

listed in the user manual. Failure to comply may result in injury and/or damage

to the product. The MRLDS-450 has not been designed to be intrinsically safe

for use in areas classified as being hazardous locations. For your safety, DO NOT use in

hazardous locations. Consult a qualified professional before connecting the MRLDS-450 to devices not mentioned in

this manual. Failure to comply may result in injury and/or damage to the product.

WARNING: The gas diffusion path can become occluded (moisture, dust, debris, frozen condensation) over time, resulting in

reduced or complete lack of gas detection and alarming function. Routine visual inspection of the gas detector and bump

testing are recommended to ensure proper gas detection and alarm function. For information on calibrating the sensor, refer to

the Care and Maintenance section of the MRLDS-450 User Manual P/N 026-1316.

CAUTION: Except for the maintenance detailed in this manual, this product should ONLY be opened and/or

serviced by authorized personnel. Failure to comply may void the warranty.

CODE COMPLIANCE: Comply with all local and national laws, rules and regulations associated with this equipment. Operators

should be aware of the regulations and standards in their industry/locality for the operation of the MRLDS-450.

TECHNICIAN USE ONLY: The MRLDS-450 must be installed by a suitably qualified technician who will install this unit in

accordance with these instructions and the standards in their particular industry/locality. This document is only intended as a

guide and the manufacturer bears no responsibility for the installation or operation of this unit. Failure to install and operate the

unit in accordance with these instructions and with industry guidelines may cause serious injury or death and the manufacturer

will not be held responsible in this regard.

Figure 1 - Refrigerant Gas Detector

Quick Start Guide

Refrigerant Gas Detector (MRLDS-450)

for Machinery Rooms, Cold Rooms and Freezers

Document Part # 026-4417 Rev 1 Page 2 of 9

Visit our website at http://www.emerson.com for the latest technical documentation and updates.

2. Component Overview

# Component Description

1M16 Cable Glands (x6)

2Rubber Gasket

3Internal Alarm Buzzer

4Power Connections (x2)

5Digital Connection (Modbus)

6Analog Connection

7Tactile Switch #1

8Ribbon Cable Connection (To Sensor)

9Tactile Switch #2

10 Relay 3 Connection (FAULT)

11 Relay 2 Connection (HIGH)

12 Relay 1 Connection (LOW)

13 Magnetic (Mag) Switch #1

14 Magnetic (Mag) Switch #2

15 M20 Cable Glands (x2)

Table 1 - Component Descriptions

Figure 2 - Component Locations

Document Part # 026-4417 Rev 1 Page 3 of 9

Visit our website at http://www.emerson.com for the latest technical documentation and updates.

3. Product Specifications

4. Installation

IMPORTANT: The manufacturer of this product requires that a bump test or calibration be performed following

installation to verify installation to verify instrument functionality.

STEP 1: Mount Gas Detector & Remove Lid

CAUTION: DO NOT allow the lid/sensor to hang from the ribbon cable. Failure to comply may result in damage to the product.

1. Mount the MRLDS-450 according to the product dimensions, maximum wiring lengths, and following

considerations:

•Environment: the full range of environmental conditions when selecting a location.

•Application: the specifics of the application (possible leaks, air movement/draft, etc.) when selecting

a location.

Size (HxWxD) 6.5” x 6.5” x 3.4” (165 x 165x 87 mm)

Weight 1.05 lbs (480g)

Indicators Multi-color Status LED

Internal Alarm Buzzer: 72dB @ 3.9” (10 cm)

Alarm Delay Configurable (0 to 15 minutes)

Inputs Tactile Switches (x2), Magnetic Switches (x2)

Outputs Analog Output: 4 to 20mA (default), 0 to 5V, 0 to 10V, 1 to 5V or 2 to 10V

Bluetooth® Bluetooth® Low Energy, BLE 4.2

Modbus Connection: RS-485 terminal block

Baud Rate: 9,600 or 19,200 (default)

Data Bits: 8

Parity: None, Odd, or Even (default)

Stop Bits: 1 (default) or 2

Retry Time: 500 ms (minimum)

Power Supply 19.5 to 28.5 VDC or 24 VAC ±20%; 4W

Wiring (Power) 2-core cable, 16 to 28 AWG

Wiring (Relays) 2-core cable, 16 to 28 AWG

Wiring (Modbus) Recommended: Belden 3106A (or equivalent) 3-core, 2 twisted pair +

ground, shielded cable with 120 Ωcharacteristic impedance,

16 to 28 AWG

Enclosure Material: ABS

Protection: IP66

Temperature Semiconductor: -40°F to 122°F (-40°C to 50°C)

Electrochemical: Ranges vary by gas type and / or concentration,

see the MRLDS-450 user manual (P/N 026-1316) for a full list of

temperature ranges.

Infrared: -40°F to 122°F (-40°C to 50°C)

Catalytic Bead: -40 to 122°F (-40°C to 50°C)

Humidity 5 to 90% RH, non-condensing

Pressure 23.6 to 32.5”Hg (800 to 1,100 mbar)

Elevation 0 to 6,560’ (3,000 m) altitude

Table 2 - Product Specifications

Document Part # 026-4417 Rev 1 Page 4 of 9

Visit our website at http://www.emerson.com for the latest technical documentation and updates.

•Accessibility: the degree of accessibility required for maintenance purposes when selecting a location.

•Target Gas: the specific gravity of the target gas when selecting the height of the instrument.

2. Using a 5/32” (4mm) hex key/allen wrench (not included), remove the lid and disconnect the ribbon cable from the base.

3. Set the lid and rubber gasket aside to be reinstalled later.

STEP 2: Wire Connections

WARNING: Ensure that all wiring connections are made BEFORE applying power.

WARNING: Relays are rated for 0 to 30V. DO NOT apply main power onto these relays.

IMPORTANT: Cable glands are meant to accommodate one cable. DO NOT use cable glands for more than one cable.

IMPORTANT: If analog output is 4 to 20mA, connect or short the connection to ensure the gas detector does not go into fault.

*IMPORTANT: The MRLDS-450 has a jumper on the analog output. This jumper MUST be removed to use the analog 4-20mA

output signal. If the jumper is removed AND the 4-20mA output signal is not used, the unit will go into fault (refer to the

026-4421 Technical Bulletin for more information).

1. Locate connections (Power, Analog, Modbus, Relays) and remove terminal blocks from the PCBA.

2. Remove plugs from the corresponding M16 cable glands and pass the cable through the opening.

3. Secure wires in each terminal block and, pressing firmly, reinstall the terminal block in the PCBA.

4. Remove all excess cable from the housing before firmly securing the cable glands.

STEP 3: Reinstall Sensor and Connect Lid

CAUTION: DO NOT leave excess cable inside of the gas detector housing. Failure to comply may result in damage to the product.

IMPORTANT: To achieve proper seal in the IP66 enclosure, the lid screws should be torqued to 15 to 20 lbf in (1.5 to 2.0 Nm).

1. Reinstall the rubber gasket. Ensure that it is correctly seated by placing the side with two grooves face down and the edge

with two bumps on the top.

Figure 3 - Locate Connections

Figure 4 - Rubber Gasket Placement

Document Part # 026-4417 Rev 1 Page 5 of 9

Visit our website at http://www.emerson.com for the latest technical documentation and updates.

2. Reconnect the ribbon cable from the sensor to the PCBA as shown:

3. Ensure no cables are interfering with the sensor module and close the lid.

4. Using a 5/32” (4 mm) hex key/allen wrench, tighten the lid screws in an Xtightening pattern:

5. MRLDS-450 Network Setup for Site Supervisor and E2

For Modbus end-of-line termination, use 150Ωohm resistor or termination block P/N 537-2711. Do not use MRLDS 120Ωohm

on-board termination with Site Supervisor or E2.

IMPORTANT:

• For 24 VAC installations sharing a transformer in a daisy-chain configuration, the neutral polarity must be

maintained for all instruments.

• 24 VAC power polarity must not be reversed.

• For a more robust system, a dedicated transformer for each MRLDS is recommended to prevent damage

caused by wiring errors.

• Fasten terminal screws.

Figure 5 - Ribbon Cable

Figure 6 - Tightening Pattern

Document Part # 026-4417 Rev 1 Page 6 of 9

Visit our website at http://www.emerson.com for the latest technical documentation and updates.

5a. Site Supervisor Device and COMM Setup

Figure 7 - Site Supervisor Setup

Document Part # 026-4417 Rev 1 Page 7 of 9

Visit our website at http://www.emerson.com for the latest technical documentation and updates.

5b. E2 Device and COMM Setup

Figure 8 - E2 Setup

Document Part # 026-4417 Rev 1 Page 8 of 9

Visit our website at http://www.emerson.com for the latest technical documentation and updates.

6. Connect MRLDS-450 to MRLDS-400 Series App (User Discretion)

The MRLDS-450 uses a smartphone application to allow users to interface with the gas detector.

IMPORTANT: Default alias, passkey, and unlock code can be changed via the MRLDS-400 Series App’s configuration menu.

1. Enable Bluetooth® discovery by tapping MAG#1 for 1 second. (After 10 seconds, the device will indicate that it is

discoverable with audible heartbeat until it has been paired, discovery has timed-out or has been canceled.)

2. Launch the MRLDS-400 App and click the Bluetooth® icon at the bottom of the screen to initiate a scan.

3. Select the instrument (default is 18TMAE) from the list of available gas detectors.

4. When prompted, enter the passkey (default is 123456).

5. Go to Configure tab to set up the device. When prompted, enter unlock code to access device configuration

(default is 1234).

6. Operation Overview

# APP DESCRIPTION

1 Main Menu (App Settings)

2 Status (Gas Concentration)

3 Calibrate (Calibration/Bump Test)

4 Details (Instrument Information)

5 Disconnect Bluetooth®

6 Restart Connected Device

7 Test Mode (LED/Buzzer/Relays/Analog

Output)

8 Device Configuration

9 Logs

Table 3 - App Description

OUTPUT

STATE LED RELAY 1 RELAY 2 RELAY 3 Buzzer

Warm-up OFF OFF OFF

Normal OFF OFF OFF

Low Alarm ON OFF OFF

High Alarm ON ON OFF

Offline OFF OFF OFF

Fault OFF OFF ON

Negative Gas Fault OFF OFF ON

Zero Cal. Fault OFF OFF OFF

Special Cal. Fault OFF OFF OFF

Table 4 - Outputs

Figure 9 - App

This document may be photocopied for personal use.

Visit our website at http://www.emerson.com for the latest technical documentation and updates.

Join Emerson Technical Support on Facebook. http://on.fb.me/WUQRnt

For Technical Support call 770-425-2724 or email ColdChain.TechnicalServic[email protected]om

The contents of this publication are presented for informational purposes only and they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or

applicability. Emerson Retail Solutions, Inc. and/or its affiliates (collectively “Emerson”), reserves the right to modify the designs or specifications of such products at any time without notice. Emerson does not assume

responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any product remains solely with the purchaser and end-user.

Document Part # 026-4417 Rev 1 Page 9 of 9

7. Part Number and Ordering Information

Scan the QR code to download the full user manual P/N 026-1316.

*Refer to the 026-4421 Technical Bulletin for more information.

For Technical Support call 770-425-2724 or email

ColdChain.TechnicalServices@Emerson.com

Emerson P/N

IP66, 3 x Relays, Analog

Output, Modbus Output,

Audible & Visual Alarms

Sensor

Type Emerson P/N Replacement Sensor Sensor

Type

Gas Type and Detection Range Pre-calibrated Sensor Modules

809-1040 CO2 0-5,000ppm IR 809-1140 CO2 0-5,000ppm IR

809-1041 CO2 0-10,000ppm IR 809-1141 CO2 0-10,000ppm IR

809-1047 R404A 0-1,000ppm SC 809-1147 R404A 0-1,000ppm SC

809-1048 R407A 0-1,000ppm SC 809-1148 R407A 0-1,000ppm SC

809-1050 R22 0-1,000ppm SC 809-1150 R22 0-1,000ppm SC

809-1056 R448A 0-1,000ppm SC 809-1156 R448A 0-1,000ppm SC

809-1066 R422D 0-1,000ppm SC 809-1166 R422D 0-1,000ppm SC

809-1068 R449A 0-1,000ppm SC 809-1168 R449A 0-1,000ppm SC

MRLDS-450 Accessories

809-1190 Calibration Adapter Kit

809-1191 Horn + strobe 24VDC; blue lens

809-1192 Horn + strobe 24VDC; amber lens

809-1193 Horn + strobe 24VDC; red lens

809-1194 Horn + strobe; blue lens; MP120K 120VAC adapter

809-1195 Horn + strobe; amber lens; MP120K 120VAC adapter

809-1196 Horn + strobe; red lens; MP120K 120VAC adapter

Table 5 - Product Ordering Information

Otros manuales para MRLDS-450

Tabla de contenidos

Otros manuales de Detector de gas de Emerson

Emerson

Emerson Rosemount 935 Manual de usuario

Emerson

Emerson MRLDS-450 Diagrama de cableado

Emerson

Emerson Rosemount 625IR Manual de usuario

Emerson

Emerson Rosemount 925FGD Manual de usuario

Emerson

Emerson Rosemount 936 Manual de usuario

Emerson

Emerson MRLDS-450 Manual de usuario

Emerson

Emerson MRLDS-450 Manual de usuario

Emerson

Emerson Rosemount 928 Manual de usuario

Emerson

Emerson MRLDS 450 Manual de usuario

Emerson

Emerson Rosemount 935 Manual de usuario

Emerson

Emerson GDU-Incus Manual de usuario

Emerson

Emerson Rosemount 925FGD Manual de usuario

Emerson

Emerson MRLDS-250 Manual de usuario

Emerson

Emerson Rosemount 935 Manual de usuario

Emerson

Emerson MRLDS-450 Manual de usuario

Emerson

Emerson Rosemount 928 Manual de usuario

Emerson

Emerson Rosemount 935 Manual de usuario

Emerson

Emerson Rosemount 935 Manual de usuario

Emerson

Emerson Net Safety MLP-A-SC1100 Manual de usuario

Emerson

Emerson GDU-Incus Manual de usuario

Emerson

Emerson Rosemount 936 Manual de usuario

Emerson

Emerson MRLDS-450 Manual de usuario

Emerson

Emerson Hart Rosemount 935 Manual de usuario

Emerson

Emerson Rosemount 936 Manual de usuario

Manuales populares de Detector de gas de otras marcas

Macurco

Macurco GD-6 Manual de usuario

Evikon

Evikon E2632 Manual de usuario

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Manual de usuario

MSA

MSA altair 5 Manual de usuario

DOD Technologies

DOD Technologies ChemLogic CL96 Manual de usuario

DEGA

DEGA NS III LCD Series Manual de usuario

RKI Instruments

RKI Instruments 35-3001A-08-01 Manual de usuario

PEMTECH

PEMTECH PT2008 Series Manual de usuario

Coster

Coster RGS 328 Manual de usuario

Sygonix

Sygonix 2483186 Manual de usuario

Perry

Perry 1GA 50917MET/P Manual de usuario

isweek

isweek AS8900 Manual de usuario

Oldham

Oldham OLC 10 Manual de usuario

Wizmart

Wizmart NB983 Manual de usuario

Beacon

Beacon MEGA Manual

RKI

RKI GX-6000 Manual de usuario

Dräger

Dräger PIR 7000 Manual de usuario

GDS

GDS GASMAX EC Manual de usuario