Emerson Provence CF2300TG01 Manual de usuario

READ AND SAVE THESE INSTRUCTIONS

“Provence” Series

Model No.

CF2300TG01

CF2300S01

CF2300OB01

CF2300WB01

Provence Series

Ceiling Fan Owner's Manual

Part No. F40BP72170001 Form No. BP7217-1

Net Weight: 23.8 Lbs.

WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.

Safety Instructions

1. Read your owner’s manual carefully and keep it for future reference.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel

disconnecting means to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the

service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off

the power to the ceiling fan before servicing.

4. Do not put anything into the fan blades while they are turning.

5. Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions for Installation

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not

operate fan without blades.

2. All wiring must satisfy National and Local Electrical Codes. Use the National Electrical Code if Local

Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical

shock. Electrical installation should be made or approved by a licensed electrician.

3. The outlet box and joist must be securely mounted an capable of reliably supporting a least 50

pounds. Use only U.L. outlet boxes listed as acceptable for fan support, and use the mounting

screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures

are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in

doubt.

4. The downrod furnished with the fan proves the minimum recommended floor to fan blade clearance

for an 8 foot ceiling.

5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental

contact with th fan blades.

6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not

know enough about electrical wiring, have your fan installed by a licensed electrician.

WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not

specifically approved for this fan.

WARNING: This product is designed to use only those parts supplied with this product and/or any

accessories designated specifically for use this product by Emerson Company could result in person-

al injury or property damage.

WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the

blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between

rotating fan blades.

WARNING

1. Open styrofoam unit containing fan. Remove top

half of styrofoam unit. Remove parts and check to

see that you have received the following:

a. Fan motor and housing assembly

b. One motor cover

c. One ceiling cover

d. Five blade flanges

e. One hanger ball/downrod assembly

f. One hanger bracket

g. One switch housing cover

h. One uplight lead assembly

i. One loose parts bag containing:

1. One setscrew

2. One 5/32" hex wrench

3. Eleven 10-32 x 5/8" oval head screws

4. Two 1” threaded studs

5. Two 1-1/4” threaded studs

6. Four knurled knobs

7. Three wire connectors

8. Two screws 8-32 x 3/8"

9. Two pull chain pendants, and couplings

10. One hairpin clip

11. One clevis pin

12. Two lockwashers

13. Sixteen 10-32 x 3/8" pan head screws

14. Sixteen flat washers

This Manual Is Designed to Make it as Easy as Possible for You to

Assemble, Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips head screwdriver One stepladder

Three wire connectors (supplied.) One wire stripper

MATERIALS

Wiring, outlet box and box connectors must be of type

required by the local code. The minimum wire would be a

3-conductor (2-wire with ground) of size shown at right:

Installed Wire Length Wire Size A.W.G.

Up to 50 ft. 14

50-100 ft. 12

Unpacking Instructions

For your convenience, check-off boxes are provided next to each step. As each step is com-

pleted, place a check mark in the box. This will insure that all steps have been completed

and will be helpful in finding your place should you be interrupted.

NOTE: Place the parts from the loose parts bags

in small containers to keep them from being lost.

If any parts are missing, contact your local retail-

er or catalog outlet for replacement before pro-

ceeding.

NOTE: Fan blades are ordered separately and are

packaged in separate carton.

FOAM

PACKING

PROTECTIVE

PLASTIC BAG

FOAM

PACKING

CARTON

MOTOR AND

HOUSING ASSEMBLY

HANGER BALL/

DOWNROD

ASSEMBLY

HANGER

BRACKET

LOOSE

PARTS BAG

BLADE

FLANGES

SWITCH

HOUSING

COVER

CEILING

COVER

MOTOR

COVER

UPLIGHT

LEAD

ASSEMBLY

If you feel you do not have enough wiring knowledge or

experience, have your fan installed by a licensed

electrician.

WARNING

Do not install or use fan if any part is damaged or

missing. Call Toll-Free:

1-800-654-3545

This product is designed to use only those parts

supplied with this product and/or any accessories

designated specifically for use with this product by

Emerson Company. Substitution of parts or acces-

sories not designated for use with this product by

Emerson Company could result in personal injury or

property damage.

WARNING

Your new ceiling fan will require a grounded electrical

supply line of 120 volts AC, 60 Hz, 15 amp circuit.

The outlet box must be securely anchored and capa-

ble of withstanding a load of at least 50 pounds.

If you feel that you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

SECTION A

Assembly Instructions

for Installing the CF2300

Ceiling Fan with a SR120

Remote Control or with a

SW140 Wall Control

1. Cut the white, blue, and black wires about 3"

above the motor coupling (Figure 1). Strip insula-

tion 1/2" from end of wires and install a wire

connector on the black wire; this wire will not be

used. Remove the wire connectors from the red

and brown wires.

2. Loosen the setscrew in the hanger ball, slide the ball

down the downrod, and remove the clevis pin. Then

slide the hanger ball off the downrod (Figure 2).

Retain all parts for reinstallation in step 11.

3. Push the wiring harness connector and the con-

nector on the blue wire (both supplied with the

SR120 Remote Control and the SW140 Wall

Control), and the connector on the uplight yellow

lead assembly (supplied with the fan) through the

downrod until they all extend about 4” out of the

downrod (Figure 3).

4. Cut all wires approximately 3" from the end of the

downrod’. Strip insulation 1/2" from end of wires.

WHITE WIRE BLACK WIRE

BLUE WIRE

REMOVE WIRE

CONNECTORS

FROM RED AND

BROWN WIRES

INSULATE BLACK

WIRE USING WIRE

CONNECTOR

YELLOW

WIRE

MOTOR

COUPLING MOTOR COUPLING SLOT

Figure 1

HANGER BALL

DOWNROD

CLEVIS PIN

SETSCREW

Figure 2

DOWNROD

CUT HERE

UPLIGHT YELLOW LEAD ASSEMBLY

WIRING

HARNESS

BLUE WIRE

Figure 3

Electrical Requirements

If your fan is to replace an existing ceiling light fixture,

turn electricity off at the main fuse box at this time and

remove the existing light fixture.

The Emerson CF2300 Ceiling Fan is designed to be

operated from a SR120 Remote Control, from a

SW140 Wall Control, or from other fan/light controls.

There are no controls supplied with the ceiling fan. If

you are going to control your ceiling fan with a SR120

Remote Control or with a SW140 Wall Control, proceed

to “SECTION A”. If you are going to control your ceiling

fan in any other manner, proceed to “SECTION B”.

Uplight

This fan is supplied with a built-in uplight in the motor

housing. This uplight does not have a built-in switch to

turn it ON or OFF. A separate switch control must be

used to operate the uplight. This can be done with a

separate ON/OFF wall switch or one of the many

Emerson Fan/Light Controls, such as the SR120,

SW140 or SW95L controls. The yellow lead supplied

with this fan is the power lead for the uplight.

To reduce the risk of fire, electric shock, or personal

injury, mount fan to outlet box marked acceptable for

fan support, and use screws supplied with outlet

box. Most outlet boxes commonly used for support

of light fixtures are not acceptable for fan support

and may need to be replaced. Consult a qualified

electrician if in doubt.

WARNING

!If the CF2300 ceiling fan is being installed with any

other control method, skip

SECTION A

and go to

SECTION B

to begin assembly instructions.

WARNING

Turning off wall switch is not sufficient. To avoid

possible electrical shock, be sure electricity is

turned off at the main fuse box before wiring. All

wiring must be in accordance with National and

Local codes and the ceiling fan must be properly

grounded as a precaution against possible electrical

shock.

WARNING

To avoid fire or shock, follow all wiring instructions

carefully.

Any electrical work not described in these instruc-

tions should be done or approved by a licensed elec-

trician.

WARNING

NOTE: Make sure the unused black motor lead is

capped with a wire connector. Make sure all wire

connectors are completely inside motor coupling

cover and not pinched between the motor

coupling cover and motor.

9. Screw two 1” threaded studs (supplied) into the

motor (Figure 6). Leave approximately 7/8” of the

stud extending above the motor. Slide the motor

cover over the downrod and rotate the cover until

the threaded studs protrude; install two knurled

knobs (supplied) to secure the cover.

10. Position the ceiling cover over the downrod. Be

sure the cover is oriented correctly, with the large

opening at the top (Figure 7).

7/8"

KNURLED KNOB

1" THREADED

STUD

MOTOR

COUPLING

COVER

WIRE

CONNECTORS

Figure 6

SETSCREW

CLEVIS PIN

MOTOR

COUPLING

DOWNROD

HAIRPIN

CLIP

MOTOR

COUPLING

HAIRPIN

CLIP

CLEVIS

DOWNROD

LEADS TO BE

POSITIONED IN

SLOT IN MOTOR

COUPLING

CLEVIS

Figure 5

5. Using wiring connectors (supplied), connect the

white, red, blue, brown, and yellow wires from the

downrod to the white, red, blue, brown and yellow

wires of the ceiling fan (Figure 4). Wires must be

connected color-to-color.

6. Fold all wires from the downrod into the slot in the

motor coupling, slide the downrod down the wires

and seat the downrod in the motor coupling. All

wires and wire connectors should be placed

through the motor coupling slot beneath the down-

rod (See Figure 5).

7. Align the clevis pin holes in the downrod with the

holes in the motor coupling. Install the clevis pin

and secure with the hairpin clip. The clevis pin

must go through the holes in the motor coupling

and the holes in the downrod (Figure 5). Push the

straight leg of the hairpin clip through the hole near

the end of the clevis pin until the curved portion of

the hairpin clip snaps around the clevis pin. The

hairpin clip must be properly installed to prevent

the clevis pin from working loose.

8. Install the setscrew (supplied in the loose parts

bag) in the motor coupling and tighten using the

5/32” setscrew wrench (supplied) (Figure 5).

FAN BLADES REMOVED

FOR CLARITY

DOWNROD

BLACK WIRE

WHITE WIRE

WIRING HARNESS

CONNECTOR

YELLOW WIRE

TO YELLOW

WIRE

BLUE WIRE

RECEIVER

BROWN WIRE

TO BROWN WIRE

YELLOW WIRE

TO YELLOW WIRE

LISTED GENERAL

USE ON/OFF

WALL SWITCH

(MUST BE

USED WITH SR120

REMOTE CONTROL)

RECEIVER

CONNECTOR

RED WIRE

TO RED WIRE

WHITE WIRE

TO WHITE WIRE

BLACK WIRE

(NOT USED)

BLUE WIRE

TO BLUE WIRE

BLACK WIRE

WHITE WIRE

BLACK

WIRE WHITE

WIRE

BLACK

WHITE

BLACK

SW140

WALL

CONTROL

FAN

HOUSING

120V SUPPLY

LIGHT FIXTURE

Figure 4

It is critical that the clevis pin in the motor coupling

is properly installed and the setscrew securely tight-

ened. Failure to verify that the pin and setscrew are

properly installed could result in the fan falling.

WARNING

15. Securely attach the hanger bracket to the outlet

box using the two screws supplied with the outlet

box (Figure 11).

11. Reinstall the hanger ball on the downrod as

follows. Route the motor leads through the hanger

ball and slide the hanger ball over the downrod

(Figure 7). Install the pin through the holes at the

top of the downrod and slide the hanger ball up

the downrod, aligning the ball so the pin is cap-

tured in the groove in the top of the hanger ball.

Pull the hanger ball up tight against the pin and

securely tighten the setscrew in the hanger ball. A

loose setscrew could create fan wobble.

12.Use three 10-32 x 3/8" pan head screws and flat

washers (supplied) to secure flange to blade

(Figure 8). Repeat for the remaining four blades.

13.Use the 10 round recessed holes in the motor hub

marked with "5" and install the five blade assemblies

(blades ordered separately) in accordance with

Step 14.

14.Attach one blade assembly to the motor hub using

two 10-32 x 5/8" oval head screws (supplied)

(Figure 9). Do not tighten completely at this time.

Install remaining blade assemblies in the same

way. Gently snug all flange screws to the motor

hub, working around the hub in a clockwise

sequence. Next, securely tighten all flange screws,

again working in a clockwise sequence. Failure to

follow this procedure could result in fan wobble.

This completes the blade installation.

SETSCREW

DOWNROD

HANGER BALL

CEILING COVER

Figure 7

MOTOR

HUB

10-32 x 5/8"

OVAL HEAD SCREWS

(2 PER BLADE

ASSEMBLY)

10-32 x 3/8" PAN HEAD

SCREW (3)

FLAT WASHER (3)

BLADE

FLANGE

Figure 8

Figure 9

CEILING

FLOOR

AT LEAST

Figure 10

It is critical that the pin in the hanger ball is properly

installed and the setscrew securely tightened.

Failure to verify that the pin and setscrew are

properly installed could result in the fan falling.

WARNING

To reduce the risk of personal injury, do not bend the

blade flanges when installing the blades or cleaning

the fan. Do not insert foreign objects between rotat-

ing fan blades.

WARNING

The fan must be hung with at least 7' of clearance

from floor to blades (Figure 10).

WARNING

The outlet box must be securely anchored and capable

of withstanding a load of at least 50 lbs.

WARNING

To reduce the risk of fire, electric shock, or personal

injury, mount fan to outlet box marked acceptable for

fan support, and use screws supplied with outlet

box. Most outlet boxes commonly used for support

of light fixtures are not acceptable for fan support

and may need to be replaced. Consult a qualified

electrician in in doubt.

WARNING

Hanger bracket must seat firmly against outlet box. If

the outlet box is recessed, remove wall board until

bracket contacts box. If bracket and/or outlet box are

not securely attached, the fan could wobble or fall.

WARNING

TWO SCREWS

SUPPLIED WITH

OUTLET BOX HANGER

BRACKET

TAB

OUTLET

BOX

OUTLET

BOX

HANGER

BRACKET

HANGER BALL/

DOWNROD ASSEMBLY

NOTE: CEILING COVER,

SUPPLY WIRES AND

FAN WIRES OMITTED

FOR CLARITY.

Figure 11

Figure 12

16. Carefully lift the fan and seat the hanger

ball/downrod assembly on the hanger bracket

that was just attached to the outlet box (Figure

12). Be sure the groove in the ball is lined up with

tab on the hanger bracket (Figure 11).

19. Securely connect the wiring harness connector to

the receiver connector, and connect the blue and

yellow wires to the blue and yellow wires from the

receiver (Figure 4).

20. Turn the receiver so that the flat side aligns with

the open side of the hanger bracket (Figure 13).

Fold and position the wires into the space above

the hanger ball and into the outlet box.

21. Feed the wires and connectors around the out-

side of the receiver, through the open side of the

hanger bracket, and into the outlet box. Slide the

receiver up and over the hanger bracket.

Remove the backing on the foam adhesive pads

and press the receiver against the ceiling.

22. To complete the ceiling fan assembly, skip to the

“FINAL ASSEMBLY” section of this Owner’s

Manual.

17. Position the receiver (supplied with the SR120

Remote Control or SW140 Wall Control) by pass-

ing the opening in the receiver over the downrod

(Figure 13).

18. Connect the black wire from the wiring harness to

the black (hot) supply wire (Figure 4). Connect the

white wire from the wiring harness to the white

(neutral) supply wiring. Connect the green ground

wires from the hanger bracket and the hanger ball

to the supply ground wire. Use wire connectors

supplied with your ceiling fan.

HANGER

BRACKET HANGER

BALL

CEILING

COVER

SW375

RECEIVER

FLAT SIDE

OPEN

SIDE

Figure 13

Failure to seat tab in groove could cause damage to

electrical wires and possible shock or fire hazard.

WARNING

To avoid possible fire or shock, do not pinch wires

between the hanger ball/downrod assembly and

hanger bracket.

WARNING

To avoid possible fire or shock, be sure that

electricity is turned off at the main fuse box before

wiring.

NOTE: If you are not sure if the outlet box is

grounded, contact a licensed electrician for advice,

as it must be grounded for safe operation.

WARNING

Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire

connectors, except for the ground wire. Do not

operate fan until blades are in place. Noise and fan

damage could result.

WARNING

9. Install the setscrew (supplied in loose parts bag) in

the motor coupling and tighten using the 5/32"

setscrew wrench (supplied) (Figure 17).

10.Screw two 1” threaded studs (provided) into the

motor (Figure 22). Leave approximately 7/8” of the

stud extending above the motor. Slide the motor

cover over the downrod and rotate the cover until

the threaded studs protrude; install two knurled

knobs (supplied) to secure the cover.

SETSCREW

CLEVIS PIN

MOTOR

COUPLING

DOWNROD

HAIRPIN

CLIP

MOTOR

COUPLING

HAIRPIN

CLIP

CLEVIS

DOWNROD

CONNECT YELLOW LEAD

TO YELLOW LEAD

CLEVIS

Figure 16

DOWNROD

SETSCREW

Figure 17

SECTION B

Assembly Instructions

for Installing the CF2300

Ceiling Fan with Any Other

Control Method

(excluding the SR120 Remote

Control or the SW140 Wall Control)

1. Position the fan motor and housing assembly in the

lower foam packing so that the top of the motor is fac-

ing you.

2. Separate, untwist and unkink the four motor leads.

3. Obtain the hanger ball/downrod assembly and

remove the hanger ball by loosening the setscrew

in the hanger ball until the ball falls freely down the

downrod (Figure 14). Remove the pin from the

downrod , then remove the hanger ball. Retain the

pin and hanger ball for reinstallation in step 9.

4. Push the uplight yellow lead assembly connector

through the downrod (Figure 15) until it extends

about 4”.

5. Cut the yellow lead approximately 3” from the end

of the pipe. Strip insulation 1/2” from end of the

wires.

6. Using the wire connector supplied, connect the

uplight yellow lead assembly to the yellow lead

from the fan motor and housing assembly (Figure

16).

7. Route the white, blue, and black motor leads through

the downrod. Fold the yellow, red, and brown wires

into the slot in the motor coupling, slide the downrod

down the wires and seat the downrod in the motor

coupling (Figure 16).

8. Align the clevis pin holes in the downrod with the

holes in the motor coupling. Install the clevis pin and

secure with the hairpin clip (Figure 16). The clevis pin

must go through the holes in the motor coupling and

the holes in the downrod . Push the straight leg of the

hairpin clip through the hole near the end of the cle-

vis pin until the curved portion of the hairpin clip

snaps around the clevis pin. The hairpin clip must be

properly installed to prevent the clevis pin from work-

ing loose. Pull on the hanger ball to make sure the

clevis pin is properly installed.

HANGER BALL

DOWNROD

CLEVIS PIN

SETSCREW

Figure 14

DOWNROD

CUT

HERE

UPLIGHT YELLOW

LEAD ASSEMBLY

Figure 15

It is critical that the clevis pin in the motor coupling

is properly installed and the setscrew securely tight-

ened. Failure to verify that the pin and setscrew are

properly installed could result in the fan falling.

WARNING

14.Use three 10-32 x 3/8" pan head screws and flat

washers (supplied) to secure flange to blade

(Figure 20). Repeat for the remaining four blades.

15.Use the 10 round recessed holes in the motor hub

marked with "5" and install the five blade assemblies

(ordered separately) in accordance with Step 16.

16.Attach one blade assembly to the motor hub using

two 10-32 x 5/8" oval head screws (supplied)

(Figure 21). Do not tighten completely at this time.

Install remaining blade assemblies in the same

way. Gently snug all flange screws to the motor

hub, working around the hub in a clockwise

sequence. Next, securely tighten all flange screws,

again working in a clockwise sequence. Failure to

follow this procedure could result in fan wobble.

This completes the blade installation.

NOTE: Make sure the red and brown leads are

capped with wire connectors. Make sure red,

brown, and yellow wire connectors are completely

inside motor coupling cover and not pinched

between the motor coupling cover and motor.

11.Position the ceiling cover over the downrod. Be

sure the cover is oriented correctly, with the large

opening at the top (Figure 19).

12.Reinstall the hanger ball on the downrod as

follows. Route the motor leads through the hanger

ball and slide the hanger ball over the downrod

(Figure 19). Install the pin through the holes at the

top of the downrod and slide the hanger ball up

the downrod, aligning the ball so the pin is

captured in the groove in the top of the hanger

ball. Pull the hanger ball up tight against the pin

and securely tighten the setscrew in the hanger

ball. A loose setscrew could create fan wobble.

13.The blue, black, yellow and white leads exiting the

downrod are 80-inches long. Before installing fan,

measure up approximately 6 to 9-inches above the

ball/downrod assembly. Cut off excess leads and

strip back insulation 1/2-inch from end of leads.

NOTE: If you are installing your fan with a SR120

Remote Control or SW 120 Wall Control, Do Not

Cut Terminal Off of the Yellow Lead.

(See Section A.)

7/8"

RED LEAD

WIRE

CONNECTORS

KNURLED KNOB

1" THREADED

STUD

MOTOR

COUPLING

COVER

WIRE CONNECTOR

YELLOW LEADS

BROWN LEAD

Figure 18

SETSCREW

DOWNROD

HANGER BALL

CEILING COVER

Figure 19

MOTOR

HUB

10-32 x 5/8"

OVAL HEAD SCREWS

(2 PER BLADE

ASSEMBLY)

10-32 x 3/8" PAN HEAD

SCREW (3)

FLAT WASHER (3)

BLADE

FLANGE

Figure 20

Figure 21

It is critical that the pin in the hanger ball is properly

installed and the setscrew securely tightened.

Failure to verify that the pin and setscrew are

properly installed could result in the fan falling.

WARNING

To reduce the risk of personal injury, do not bend the

blade flanges when installing the blades or cleaning

the fan. Do not insert foreign objects between rotat-

ing fan blades.

WARNING

17. Securely attach the hanger bracket to the outlet

box using the two screws supplied with the outlet

box (Figure 23).

18. Carefully lift the fan and seat the hanger

ball/downrod assembly on the hanger bracket that

was just attached to the outlet box (Figure 24). Be

sure the groove in the ball is lined up with tab on

the hanger bracket (Figure 23).

NOTE: If you are installing a SR120 Remote

Control or a SW140 Wall Control to operate the

fan and light, refer to the installation instructions

and wiring diagrams shown in Section A of this

Owner’s Manual.

19. For a wall control installation you will need a

three-wire (with ground) conductor cable between

the ceiling and wall outlet boxes. This will allow

you to control the fan separately from the lights.

Figure 25 is a basic wiring diagram that will con-

trol the uplight and downlight on a switch and the

fan on a separate control. Refer to the installation

instructions and wiring diagrams supplied with the

Emerson Fan Control Owner’s Manual.

a. Connect the green grounding lead from the

hanger ball and the green grounding lead from

the hanger bracket to the grounding conductor

of supply (this may be a bare wire or a wire

with green colored insulation). Securely con-

nect wires with wire connector supplied.

b. Securely connect the white wire from the

downrod to the supply white (neutral) wire

using wire connector supplied. Securely con-

nect the black wire from the downrod to the

supply black (hot) wire using wire connector

supplied.

c. Cut terminal off of the yellow lead wire and

strip insulation 1/2” from end of wire.

d. Securely connect the blue wire and yellow wire

from the downrod to the supply red (hot) wire

using wire connector (supplied). After connec-

tions have been made, turn leads upward and

carefully push leads into the outlet box, with

the white and green leads on one side of the

outlet box and the black, blue and yellow leads

on the other side of the outlet box.

20. To complete the ceiling fan assembly, proceed to

the “FINAL ASSEMBLY” section.

CEILING

FLOOR

AT LEAST

Figure 22

TWO SCREWS

SUPPLIED WITH

OUTLET BOX HANGER

BRACKET

TAB

OUTLET

BOX

OUTLET

BOX

HANGER

BRACKET

HANGER BALL/

DOWNROD ASSEMBLY

NOTE: CEILING COVER,

SUPPLY WIRES AND

FAN WIRES OMITTED

FOR CLARITY.

Figure 23

Figure 24

The fan must be hung with at least 7' of clearance

from floor to blades (Figure 22).

WARNING

The outlet box must be securely anchored and capable

of withstanding a load of at least 50 lbs.

WARNING

To reduce the risk of fire, electric shock, or personal

injury, mount fan to outlet box marked acceptable for

fan support, and use screws supplied with outlet

box. Most outlet boxes commonly used for support

of light fixtures are not acceptable for fan support

and may need to be replaced. Consult a qualified

electrician in in doubt.

WARNING

Hanger bracket must seat firmly against outlet box. If

the outlet box is recessed, remove wall board until

bracket contacts box. If bracket and/or outlet box are

not securely attached, the fan could wobble or fall.

WARNING

Failure to seat tab in groove could cause damage to

electrical wires and possible shock or fire hazard.

WARNING

To avoid possible fire or shock, do not pinch wires

between the hanger ball/downrod assembly and

hanger bracket.

WARNING

To avoid possible fire or shock, be sure that

electricity is turned off at the main fuse box before

wiring.

NOTE: If you are not sure if the outlet box is

grounded, contact a licensed electrician for advice,

as it must be grounded for safe operation.

WARNING

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de Emerson

Emerson

Emerson CURVA SKY CF152ORB00 Manual de usuario

Emerson

Emerson RAPHAEL CF2605PW00 Manual de usuario

Emerson

Emerson Carrera CF784BS00 Manual de usuario

Emerson

Emerson CF705AB04 Manual de usuario

Emerson

Emerson CF653WW00 Manual de usuario

Emerson

Emerson CF921BS00 Manual de usuario

Emerson

Emerson CF705BS04 Manual de usuario

Emerson

Emerson BUILDER UNIPACK CF701ORB00 Manual de usuario

Emerson

Emerson CF766BS00 Manual de usuario

Emerson

Emerson SUMMER NIGHT CF742PFSCB 01 Manual de usuario

Emerson

Emerson HF1160BQ02 Manual de usuario

Emerson

Emerson AVANT ECOCF921VNB01 Manual de usuario

Emerson

Emerson HIGHGROVE CF990BS00 Manual de usuario

Emerson

Emerson CF2800BS Manual de usuario

Emerson

Emerson Enardo 4000 Manual de usuario

Emerson

Emerson PRO CF710BS03 Manual de usuario

Emerson

Emerson CF705ORB04 Manual de usuario

Emerson

Emerson CF712AB02 Manual de usuario

Emerson

Emerson Botanica CF2500HTW01 Manual de usuario

Emerson

Emerson CF710AB00 Manual de usuario

Emerson

Emerson CF788CK00 Manual de usuario

Emerson

Emerson DC BUILDER ES Series Manual de usuario

Emerson

Emerson AMHURST CF880BS00 Manual de usuario

Emerson

Emerson AMHURST CF880VS Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje

Litex Industries

Litex Industries E-CGL52CB5C1 Manual de usuario