Emerson Keystone EPI2 Manual de usuario
Installation, Operation and Maintenance Manual
MAN-10-04-100-0720-EN Rev. 2
October 2019
Keystone EPI2
Logic Board Firmware Upgrade Programmer ICD-U64 Procedure
I
Installation, Operation and Maintenance Manual
MAN-10-04-100-0720-EN Rev. 2
Table of Contents
October 2019
Table of Contents
Table of Contents
Section 1: Firmware Upgrade
1.1 Tools ............................................................................................................. 1
1.2 ICD-U64 Programmer Preparation ................................................................ 3
1.3 Firmware Update .......................................................................................... 4
1.4 Firmware Upload........................................................................................... 4
1.5 Actuator Settings Checklist ......................................................................... 16
October 2019
Installation and Maintenance Instructions
MAN-10-04-100-0720-EN Rev. 2
Firmware Upgrade
Section 1: Firmware Upgrade
This procedure details how to program rmware on the logic board for the EPI2 Actuator
using the ICD-U64 Programmer.
1.1 Tools
WARNING
Installation, conguration, commissioning, maintenance, and repairs must be performed
by approved and qualied personnel only.
NOTICE
Certain nameplates may carry more than one approval, and each approval may have
unique installation/wiring requirements and/or conditions of "safe use", installation, and
maintenance. These special instructions are in addition to and may override the standard
installation procedures. Special instructions are listed by approval type.
To update the rmware of EPI2 actuators, the following tools are necessary:
• PC with program CSSLOAD-CCS Programmer Control Software installed
(Figure 1). This software can be downloaded from:
http://www.ccsinfo.com/content.php?page=ccsloadsw
• PC with USB Drivers for all CSS programmers/debuggers
• Firmware “F02_63_125_v3_11.X.production”, for models E006, E013 or
latest revision
• Firmware “F02_250_500_v4_12.X.production”, for models E025, E051, E091,
E171 or latest revision
• The Universal programmer ICD-U64 (Figure 2)
• Logic Board or Actuator
• Cable from the ICD-U64 to the processor card rmware programming connector
part number: VA001-692-15
Figure 1
1
Section 1: Firmware Upgrade
Installation and Maintenance Instructions
MAN-10-04-100-0720-EN Rev. 2 October 2019
Firmware Upgrade
Figure 2 ICD-U64 CCS Programmer
Figure 3 EPI2 Logic Board
Table 1. Programming Connector Pinout
Signal ICD-U64 Pinout EPI2 Logic Board J15
Real Time Debugging Pin 1
ICSP Clock Pin 2 Pin 5
ICSP Data Pin 3 Pin 4
GND Ground Pin 4 Pin 3
VDD Power Pin 5 Pin 2
MCLR Pin 6 Pin 1
2
Section 1: Firmware Upgrade
October 2019
Installation and Maintenance Instructions
MAN-10-04-100-0720-EN Rev. 2
Firmware Upgrade
1.2 ICD-U64 Programmer Preparation
The ICD-U64 Programmer has an internal jumper to select multiple options to power the
target board (actuator logic board).
1. ICD-U64 programmer internal jumper selecting 5V
This conguration allows the ICD-64 Programmer to provide power to the logic board.
This conguration can be used to program the logic board as standalone board or to
program the logic board while installed in the actuator. The rmware upgrade of the logic
board should be successful regardless if the logic board is powered from the actuator
power supply or ICD-U64 programmer.
2. ICD-U64 no jumper
The ICD-U64 internal jumper is not present or was set to no power the target board. It's
not possible to upgrade rmware in the logic board as a standalone board since no power
is being supplied to the target board. If the logic board is installed in the actuator, the
actuator requires to be powered on to have a successful rmware upgrade. Note that a new
programming tool will likely have this no voltage setting.
3. ICD-U64 programmer internal jumper selecting 3.3V
This option must not be selected, it is not applicable for the EPI2 Actuator.
3
Section 1: Firmware Upgrade
Installation and Maintenance Instructions
MAN-10-04-100-0720-EN Rev. 2 October 2019
Firmware Upgrade
1.3 Firmware Update
After downloading the new rmware, the actuator settings will return to their default
values. As such, the settings in place prior to the rmware download will need to be set
again. For this reason, be sure to store the actuator settings (e.g. opening speed, closing
speed, % opening torque, % closing torque). Refer to Section 6.2 (Local Conguration of
the EPI2) in the actuator IOM for details. To be clear, all settings will be returned to the
factory default values, it is necessary to reset the open/close travel limits; also, the motor
will default to the smallest size.
If not correctly reset the unit will alarm in open torque.
OM1 settings are not required to be reset because they are unaffected by the processor
card rmware ash.
1.4 Firmware Upload
This procedure is based on the CCS Inc. CCSLOAD ICD-U64 programming tool- This tool can
power the microprocessor from the USB port of the PC, using the 5V setting and also from
the actuator, using the actuators power source. The microprocessor to be ashed is referred
to as the “target”. Take care that the target is only powered from one source, not both.
In some eld installations is difcult to remove power from the actuator, this procedure
provides instructions in how to download rmware without removing the power from the
actuator, therefore instructions in the procedure must be followed to avoid any damage to
the actuator or any personal injury.
1. It is necessary to identify the position of the jumper inside the ICD-U64
programmer before downloading rmware as indicated in step 1.2.
2. To program the logic board as standalone board, connect the ICD-U64
programmer as shown in the picture and proceed in step 9.
4
Section 1: Firmware Upgrade
October 2019
Installation and Maintenance Instructions
MAN-10-04-100-0720-EN Rev. 2
Firmware Upgrade
3. To program the logic board as part of an actuator with no OM1 board present,
carefully connect the ICD-U64 programmer as shown in the pictures and proceed
in step 9.
Figure 4
4. To program the logic board as part of an actuator with an OM1 board present,
and the actuator is powered ON.
CAUTION
Accessing the electronics compartment while the actuator is in service exposes the
technician to lethal voltage and possibly from more than one source.
Set the OM1 switch SW4 in ON position, it will prevent the actuator from stroking during
rmware download, and it will allow to maintain the actuator in the last position requested
by the 4-20mA or the 0-10V loop control.
Switch SW4 in
ON position
5
Section 1: Firmware Upgrade
Installation and Maintenance Instructions
MAN-10-04-100-0720-EN Rev. 2 October 2019
Firmware Upgrade
5. Note the position then remove the yellow position indicator to allow the OM1
board to be slightly moved to the side and have access to the programming
connector found in the actuator logic board.
6. Carefully remove the 4 screws that are holding the OM1 board. If the actuator is in
vertical position, there is a risk of dropping the screws inside the actuator. Dropping
the screws inside the actuator could cause a short circuit if the screws drop in the
power board, or a damage of the gears if the screws drop in the gears section.
OM1 board screws
6
Section 1: Firmware Upgrade
October 2019
Installation and Maintenance Instructions
MAN-10-04-100-0720-EN Rev. 2
Firmware Upgrade
7. Once all the screws have been removed, carefully place an insulator material
underneath the OM1 board to protect the board from the metal spacers
contacting the circuit board shorting the board or I/O's to ground. Place the OM1
board slightly to the front to allow access to the programming connector in the
actuator logic board.
Insulator
Programming connector
7
Section 1: Firmware Upgrade
Otros manuales para Keystone EPI2
1
Tabla de contenidos
Otros manuales de Controladores de Emerson
Emerson
Emerson Fisher 67C Series Manual de usuario
Emerson
Emerson Dixell XR20T Manual de usuario
Emerson
Emerson Unidrive M400 Manual de usuario
Emerson
Emerson Site Supervisor Manual de usuario
Emerson
Emerson Fisher MR95 Series Manual de usuario
Emerson
Emerson uerdant VX Series Manual de usuario
Emerson
Emerson Fisher 92S Manual de usuario
Emerson
Emerson Fisher R622 Manual de usuario
Emerson
Emerson S402Y Manual de usuario
Emerson
Emerson Fisher 4194S Manual de usuario
Emerson
Emerson CASH VALVE B-95 Manual
Emerson
Emerson Dixell iProChill IPC115D Guía del usuario
Emerson
Emerson EZH Series Manual de usuario
Emerson
Emerson Spence T61 Series Manual de usuario
Emerson
Emerson EC1-233 Manual de usuario
Emerson
Emerson Dixell XM670K Diagrama de cableado
Emerson
Emerson Fisher FIELDVUE DVC5000 Guía de configuración
Emerson
Emerson Liebert PEX+ Series Manual de usuario
Emerson
Emerson Advantage 2.1 Manual de usuario
Emerson
Emerson EXD-HP1 Manual de usuario
