Emerson E2 Manual de usuario
quick start guide
Document Part # 026-4921 Rev 0 03-MAY-2012
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
E2 Setup with Carrier Corporations RTU Open
Controller for 527-0359
This document will guide you through setting up and commissioning the Carrier Corpora-
tions RTU Open Controller in the E2 controller (CARRIER OPN-RTUM Open Echelon device in
the E2).
E2 and Echelon Devices Communications Network Wiring Diagram
Note that Open Echelon Description files require E2 firmware version 3.01FO1 or higher.
Figure 1 - Network Wiring Diagram
E2 Setup with Carrier Corporations RTU Open Controller for 527-0359
Document Part # 026-4921 Rev 0 03-MAY-2012 Page 2 of 14
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
Controller Board Echelon Network Cable Connections
Carrier Corporations RTU Open Controller Board (SW3) Dip Switch Set-
tings
Set SW3 Dip Switches As Shown
BAUD RATE DS-1 DS-2 DS-3 DS-4 DS-5 DS-6 DS-7 DS-8
38.4K baud ON OFF OFF ON OFF ON ON OFF
Figure 2 - Echelon Network Cable Connections
E2 Setup with Carrier Corporations RTU Open Controller for 527-0359
Document Part # 026-4921 Rev 0 03-MAY-2012 Page 3 of 14
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
Third Party Hardware Configuration Notation
The RTU Opens operation depends upon its occupancy state (Occupied/Unoccupied). The
RTU Open operates continuously in the Occupied Mode by default until the occupancy
schedule has been configured.
NOTE: The controllers OCCUPANCY SOURCE point setting must be initiated through the
Third Party hardware and software setup procedures in order for any Building Automation
System (BAS) to control Occupancy Schedule.
The OCCUPANCY SOURCE point setting must be configured as follows:
3 = BAS ON/OFF
STEP 1: Upload the description file to the E2 controller.
1. From UltraSite, connect to your E2 controller.
2. Right-click the E2 icon and select Description File Upload.
3. Browse to the location of the description file and click Upload.
4. After uploading, you will need to reboot the E2 controller.
Figure 3 - Description File Upload
E2 Setup with Carrier Corporations RTU Open Controller for 527-0359
Document Part # 026-4921 Rev 0 03-MAY-2012 Page 4 of 14
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
STEP 2: Activate the license of the device.
5. From the E2 front panel (or via the Terminal Mode), press , 7(System Configura-
tion), and 9(Licensing).
6. Press F1 (ADD FEATURE) and enter your license key.
STEP 3: Once the license is activated, add the device to the E2 controller.
7. Press , 7(System Configuration), 7(Network Setup), 2(Connected I/O Boards &
Controllers).
8. Press F2 (NEXT TAB) to go to the C4: Third Party tab. You should see the device in the list.
Enter the number of devices to add and press the button to save your changes.
Figure 4 - Add License Screen
E2 Setup with Carrier Corporations RTU Open Controller for 527-0359
Document Part # 026-4921 Rev 0 03-MAY-2012 Page 5 of 14
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
Figure 5 - Specify the Number of Devices to Add
Figure 6 - Device Setup Screen
E2 Setup with Carrier Corporations RTU Open Controller for 527-0359
Document Part # 026-4921 Rev 0 03-MAY-2012 Page 6 of 14
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
STEP 4: Commission the Echelon device.
9. Press , 7(System Configuration), 7(Network Setup), 1(Network Summary).
10.Use the UP and DOWN arrow keys to highlight the device name and then press
(Commission).
11.Select the method to use for identifying the device. Select from the list:
1 = Service Pin --> The physical button on the controller must be pressed. This is the
preferred method for device accuracy.
2 = Entering Neuron ID(s) directly --> Echelon device address should consist of 12
characters. The device is identified via remote communication using the Neuron ID.
Use this selection if the Neuron ID of the device is available.
3 = Specifying a range of nodes --> The network is scanned for neuron addresses.
Figure 7 - Commission the Device
E2 Setup with Carrier Corporations RTU Open Controller for 527-0359
Document Part # 026-4921 Rev 0 03-MAY-2012 Page 7 of 14
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
Figure 8 - Select Method for Identifying the Controller
Figure 9 - Identifying the Controller Using the Neuron ID
E2 Setup with Carrier Corporations RTU Open Controller for 527-0359
Document Part # 026-4921 Rev 0 03-MAY-2012 Page 8 of 14
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
STEP 5: Name the controller device.
12.Press , 7(System Configuration), 7(Network Setup), 1(Network Summary).
13.Use the UP and DOWN arrow keys to highlight the generic LonMark Device name and
then Press (SETUP).
14.Enter the desired device name in the Name field highlighted and then press the to
return to the Network Summary screen.
NOTE: By default, any Third Party (Open Echelon) devices that are initiated in E2 will always
have a generic naming sequence as shown:
Example: LONMARK_001, LONMARK_002, LONMARK_003
Figure 10 - Network Summary Screen
E2 Setup with Carrier Corporations RTU Open Controller for 527-0359
Document Part # 026-4921 Rev 0 03-MAY-2012 Page 9 of 14
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
Figure 11 - Changing the Device Name
Figure 12 - Changing the Device Name
E2 Setup with Carrier Corporations RTU Open Controller for 527-0359
Document Part # 026-4921 Rev 0 03-MAY-2012 Page 10 of 14
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
STEP 6: View the device Status Screen.
15.Press and then 5(Configured Applications). A list of all configured applications in
E2 displays on the screen.
16.Use the UP and DOWN arrow keys to highlight the device name on the Configured Appli-
cations screen and then press . The device Status Screen displays.
NOTE: By default, if there are one or more devices of the same type configured in E2, a list of
all common devices will display (Summary Screen) in reference to the numeric or alphanu-
meric character sequence of the devices labeled.
Example: AHU-1, AHU-2, AHU-3, RTU-1, RTU-2, RTU-3
Figure 13 - Network Summary Screen
Otros manuales para E2
15
Otros manuales de Controladores de Emerson
Emerson
Emerson Fisher L2 Manual de usuario
Emerson
Emerson dixell XR03CX Diagrama de cableado
Emerson
Emerson NZ Series Manual de usuario
Emerson
Emerson Damcos KC 65 Manual de usuario
Emerson
Emerson MultiFlex ESR Manual de usuario
Emerson
Emerson Branson 2000X Manual de usuario
Emerson
Emerson Lumity E3 Manual de usuario
Emerson
Emerson Fisher FIELDVUE DVC6005 Series Manual de usuario
Emerson
Emerson Fisher EZH Series Manual de usuario
Emerson
Emerson Autochangeover Controllers AC8 Manual de usuario
Emerson
Emerson Bettis RP4AF Manual de usuario
Emerson
Emerson Bettis Nuclear Series Manual de usuario
Emerson
Emerson DIXELL XR77CHC Manual de usuario
Emerson
Emerson Control Link Refrigeration System Controller Manual de usuario
Emerson
Emerson FloBoss 107 Manual de usuario
Emerson
Emerson Fisher 4194S Manual de usuario
Emerson
Emerson Yarway Integral Strainerimpulse 400 Series Manual de operación y mantenimiento
Emerson
Emerson Fisher 585C Series Manual de usuario
Emerson
Emerson DSM314 Manual de usuario
Emerson
Emerson Bettis EHO Manual de usuario
