EMC Celerra NS20 Manual de usuario

EMC®Celerra®NS20 System

(Dual Blade)

Installation Guide

P/N 300-007-635 Rev A01

EMC believes the information in this publication is accurate as of its publication date. The information is

subject to change without notice.

THE INFORMATION IN THIS PUBLICATION IS PROVIDED “AS IS.” EMC CORPORATION MAKES NO

REPRESENTATIONS OR WARRANTIES OF ANY KIND WITH RESPECT TO THE INFORMATION IN

THIS PUBLICATION, AND SPECIFICALLY DISCLAIMS IMPLIED WARRANTIES

OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE.

Use, copy or distribution of any EMC software described in this publication requires an applicable software

license.

All other trademarks used herein are the property of their respective owners.

For the most up-to-date regulatory document for your product line, go to the Technical Documentation

andAdvisories section on EMC Powerlink. For the most up-to-date listing of EMC product names, see EMC

Corporation Trademarks on EMC.com.

After reviewing this guide, go to Celerra Tools or Powerlink and download the client product guides to

complete your MPFS installation. Log on to Powerlink, open Support > Technical Documentation and

Advisories > Software ~C~ Documentation > Celerra MPFS over Fibre Channel or Celerra MPFS over

iSCSI.

The label, settings, and system cabling information in this document are for your reference. Paste the

Control Station label in this provided space, see page 7.

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

Before you begin

Welcome

The system you are about to install comes factory pre-loaded with Celerra®Network Server software

(DART) and CLARiiON®storage array software (FLARE®).

Software upgrade

If you bought a software maintenance contract, you are entitled to a software upgrade that is

performed only after the installation, Celerra Startup Assistant (CSA), and registration have

successfully completed.

Site preparation

Complete the site preparation by verifying the following activities before installation:

Network connections•

Power requirements•

Rack space requirements•

Default IP addresses

The system components communicate with each other using a private Internet Protocol (IP) network.

By default, this network uses the IP addresses listed in the following table.

If your existing IP network uses addresses on these subnets, you are required to change the private

network addresses of your Celerra Network Server to different subnets before the installation.

Primary internal network 128.221.252.100

Backup internal network 128.221.253.100

Netmask 255.255.255.0

IP address of storage processorA 128.221.252.200

IP address of storage processor B 128.221.253.201

Gateway IP address of storage processorA 128.221.252.104

Gateway IP address of storage processor B 128.221.253.104

Internal system addresses Factory values

Installation overview

EXP

PRI

EXP

PRI

EXP

PRI

EXP

PRI

Step 5. Configure for production.

This CD contains the intellectual property of

EMC Corporation or is licensed to EMC Corporation

from third parties. Use of this CD and the intellectual

property contained herein is expressly limited to the

terms and conditions of the License Agreement.

EMC® Celerra® NS20 System

Tutorial CD

CSA Installation

P/N nnn-nnn-nnn-A0n

C®

C®C

elerra® NS20

ele

Cel

C®

System

Tutorial CD

CSA Installation

P/Nnnn-nnn-nnn-A

AllRights R

MC®

EMC® Celerra® NS20

Back Next Cancel

EMC® Celerra® NS20 System

Tutori al

CSA Installation

P/N nnn-nnn-nnn-A0n

EMC®

Tutorial

CSA Installation

P/N nnn-nnn-nnn-A0n

Installation

Step 1. Order the product

and prepare the site.

Step 4. Register with the

service provider.

Step 3. Install the Celerra

Startup Assistant.

Implementation

Step 2. Assemble and cable

the product on site.

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

Installation steps:

Review and complete the Celerra worksheets (see pages 19 and 20), and verify that the site is1.

properly prepared for the installation of your Celerra NS20. About 20 minutes.

If your Celerra NS20 is to be installed in a customer-supplied rack, use this document to unpack2.

the system from the disposable mini-rack shipping container, and install the system in your available

rack. About 40 minutes.

Note: If your Celerra NS20 system arrives at your site in a pre-installed cabinet and is previously

cabled, verify the cabling before you begin the use of your system.

Cable your system according to the instructions and illustrations contained in this document.

Ensure that all of your cables are seated securely. About 45 minutes.

When you install your Celerra NS20, use the Celerra Startup Assistant (CSA) to conﬁgure your3.

system. The CSAis on the Celerra Applications & Tools CD. The CSA will help create CIFS shares,

NFS exports, or iSCSI LUNs and to register your Celerra system. About 15 minutes.

Celerra Startup Assistant, your request for support from EMC®Customer Service will be delayed.

About 5 minutes.

Implementation step:

5. After you have registered your Celerra NS20 system, you must conﬁgure the system for

production. There are several documented implementation procedures based on common

usages. You can conﬁgure your system manually using Celerra Manager, or follow the common

implementations listed below.

Common implementations:

Create CIFS shares• Create iSCSI LUNs• Create NFS exports• Perform Common Post-CSA tasks•

At the end of each implementation, your system will be usable and ready for production.

Note: Conﬁgure your system using these procedures to create basic implementations.

To conﬁgure additional implementations, follow the Celerra user documentation on Powerlink®.

Installation steps

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

Unpacking the Celerra NS20 system

If your Celerra NS20 system was purchased and shipped in an EMC 40 Unit cabinet, (70 in. tall,

where1 unit =1.75 in.), start on page 11 of this document and conﬁrm that the cables are

installed correctly and securely; otherwise start unpacking your Celerra NS20 system from the

disposable mini-rack shipping container.

CNS-000855

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

Disposable mini-rack Document kit inventory list

Disk-array enclosure Doc kit: Installation guide

Control Station Read Me First

Standby power supply Cabling diagrams

Storage processor enclosure Environmental compliance information

Blade enclosure Notices

Accessory box 1 Media kit inventory list

Accessory kit docs and bezels Applications and Tools CD

Power cables Software CD

Standby power supply interconnect cable kit User documentation CD

Crossover cable Getting Started with Celerra

Serial cable

Note: The shaded areas in the table represent separate containers, packages, and boxes.

If additional accessory boxes are necessary, they will be shipped separately.

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

LAN1

LAN2

Disk-array

enclosure

Standby power

supply

Control Station

Blade enclosure

Document kit inventory list

and Media kit inventory list

Storage processor

Disposable

mini-rack

IMPORTANT

User Documentation

Accessory box

CIP-1038MOD

Remove this label and

paste it on page 2

of this guide.

Contents of the disposable mini-rack

Remove components from shipping container

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

2. Carefully set aside each

component as it is removed from

the mini-rack shipping container.

Caution: Two people are required to remove the components. Only remove screws

holding the components in place at this time. Do not remove the screws holding

the rails in place; this may cause damage to the components. Only remove one

component at a time.

3. The rails remain in the mini-

rack shipping container at this

time.

Front

Mini-rack

Control Station

Storage processor

enclosure

Standby power

supply

Disk-array

enclosure

Blade enclosure

Remove ONLY

8 screws

per side.

Remove ONLY

8 screws

per side.

CIP-001034MOD

Disk array

Standby power supply

Control Station

Blade enclosure

Storage processor

Using a #21. Phillips-head screwdriver,

remove only 8 screws per side. Keep the

removed screws to install the components

in the rack.

Remove rails and install into the site rack

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

1. Remove the screws holding the

rails in place. Keep the screws

to install the rails in your rack.

The mini-rack is part of the

shipping container and is not to be

removed.

2. Insert the rail slide and seat

the rail extensions into the rear

channel of your rack.

3. Do not fully tighten the two initial

screws that join the rails to the rack.

Allow some adjustment space for

the installation of the components.

Rail slide

Rail extensions

Remove rear screws.

CNS

000854

Front of your rack

Rear of your rack

Rail slide

he initial 2 screws on

each side of the rack hold

the rails in place.

Rail extensions

Install rear screws.

Only remove the screws

holding the rails in the mini-rack.

There are 8screws that hold the rails

into the mini-rack.

Protruding PEM screw holes

are located in 4 places on

the front of the rails.

Conserve rack space

when installing rails.

Marked holes on both

rails indicate the place

for initial screws.

Threaded

screw holes

Remove the rails.

Components, latches, and bezels

Screws (2 per side)

Front

A and B

bezel bracket

Snap on bezels

Rail catch

Screw (1 per side)

Control Station and standby

power supply shelf

Disk-array enclosure

2 bracket screws each side

Front

Indentation

to center of

the rack

Install the lower

screw rst

screws (2 per side).

Storage processor enclosure

and blade enclosure

Front

2 screws

each side

Install screws through rack

into the rail, 1a through 4a.

Install the bottom component rst.

Ensure that each component

is secure before you install the

component above it.

CIP-001033MOD

Install the rack and rails with the provided screws.1.

Starting with the bottom component ﬁrst, install each component.2.

Ensure that each component is installed securely.3.

Install the latches as you install the components.4.

After all the components and latches are in place, snap on the bezels.5.

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

Otros manuales para Celerra NS20

Tabla de contenidos

Otros manuales de Almacenamiento de EMC

EMC

EMC Disk Library DL4106 Manual de usuario

EMC

EMC VNX Series Manual del propietario

EMC

EMC VNX Series Manual de usuario

EMC

EMC Symmetrix DMX-3 Manual de usuario

EMC

EMC VNX5500 Manual de usuario

EMC

EMC Celerra NS20 Instrucciones de uso

EMC

EMC CelerraNS-120 Manual de usuario

EMC

EMC AX4-5 Manual de usuario

EMC

EMC VNX Series Manual del propietario

EMC

EMC DLm120 Manual técnico

EMC

EMC Atmos Instrucciones de instalación

EMC

EMC Connectrix EC-1200 Manual técnico

EMC

EMC VNX Series Manual de usuario

EMC

EMC CX700 Manual técnico

EMC

EMC Celerra Manual de usuario

EMC

EMC CloudBoost 100 Instrucciones de montaje

EMC

EMC VNX5300 Block Manual del propietario

EMC

EMC Data Domain DD860 Instrucciones de montaje

EMC

EMC EMC2 DATA DOMAIN DD660 Instrucciones de montaje

EMC

EMC CLARiiON CX4-120 Manual de usuario

EMC

EMC CLARiiON AX150 Series Guía del producto

EMC

EMC FC4700 Manual técnico

EMC

EMC Celerra NX4 Manual de usuario

EMC

EMC Celerra NS20FC Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario