Emax TINYHAWK III Manual de usuario
Thanks for purchasing the Tinyhawk III.
Please follow the instruction manual to assemble and configure your Tinyhawk.
Design in California, Made in China
Disclaimer
1.
Please read the disclaimer carefully before using this product.
2.
By using this product, you hereby agree to this disclaimer and signify that you have read
them carefully and completely.
3.
This product is not suitable for people under the age of 18. Adult supervision is highly
recommended for kids under the age of 18.
4.
Our Tinyhawk features open-source flight controller and Electronic Speed Controllers to
meet the FPV enthusiasts' need to upgrade their quad.
5.
Please read the instruction manual and warnings carefully. Before every flight, make sure
the battery is fully charged and power connections are secure.
6.
DO NOT fly around crowds, children, animals or objects.
7.
EMAX ACCEPTS NO LIABILITY FOR DAMAGE(S) OR INJURIES INCURRED DIRECTLY
OR INDIRECTLY FROM THE USE OF THIS PRODUCT.
Precautions
1.
Please follow the instructions to assemble and to operate this product in a proper way.
2.
Pilots do not use this product if you have physical or mental illness, dizziness, fatigued, or
use while under the influence of alcohol or drugs.
3.
Please fly in a safe area away from people
4.
Do not modify or use other parts and accessories not approved for the use of EMAX.
5.
Do not use this product in harsh environments (such as winds, rain, lightning, snow, etc.).
6.
Do not use this product in a strong electromagnetic environment.
Product specification
Tinyhawk III
Wheelbase
76mm
Maximun Size
L*W*H=105x105x45mm
Weight(Without battery)
~32g
Motor
TH0802 II 15000KV
Propeller
Avan TH Turnlemode-3
Main board
F4（STM32F411 firmware ）
4in1 /5A ESC
EMAX Tiny Receiver（SPI/Frsky_D8 ）
Camera
RunCam Nano 4 Camera
VTX
200-100-25mW 37CH
(Adjustable frequency)
Support SmartAudio
Battrey
1S HV 450mAh
Frequency
5.8GHz（5658MHz-5945MHz）-TX
Use 5733 –5866 MHz In USA
2.4GHz（2400MHz-2483.5MHz）-RX
EMAX E8 Transmitter
Maximun Size
L*W*H=150x140x45mm
Weight(Without battery)
~260g
Frequency
2.4GHz（2400MHz-2483.5MHz）-TX
Battrey
18650 Lithium ion battery
Charging System
Built in USB 1A linear lithium ion
battery charging system
Working Voltage
4.2V-3.3V
External interface
Micro USB,3.5mm Audio interface
(wired coach interface)
EMAX Transporter 2
Maximun Size
(Without antenna,Folded)
L*W*H=155x100x90mm
Weight(Without battery)
~398g
Screen resolution
480X800
Screen size
4.3 inch
Battrey
1300mAh Lithium ion battery
Working Voltage
4.2V-3.7V
Frequency
5.8GHz（5658MHz-5945MHz）-RX
Use 5733 –5866 MHz In USA
Charging System
Built in USB 1A linear lithium ion
battery charging system
DVR
32G TF card（max），MJPEG，AVI
Video
VGA/D1/HD
Off/3min/5min/10min
Product list
1.
Tinyhawk III.......................................... ×1
2.
EMAX E8 Transmitter.........................×1
3.
EMAX Transporter 2 ...........................×1
4.
Emax 1s HV 450 mAh.........................×1
5.
Charger................................................ ×1
6.
Propeller ............................................. (2XCW, 2XCCW)
7.
Accessory package ................................1
1.E8 Transmitter
1.1 E8 Transmitter
1.2 Power on & off
Press and hold the power button while the center indicator light turns on red. After 2
seconds, the center indicator light turns from red to green, and it powers on.
Press and hold the power button, after 2S, the center indicator will go out, and it will
shutdown.
1.3 Binding & Unbinding
The E8 Transmitter has been bound with Tinyhawk III in the RTF kit. If it is necessary to
bind, please follow the steps below:
1.
Enabling Bind Mode: Turn on the power and after the Tinyhawk III starts, press and hold
the bind button to make the Tinyhawk III enter Bind Mode. When the blue indicator light
of the Tinyhawk III flight controller flashes, this is indicating that it has entered Bind Mode.
2.
E8 Transmitter enters binding mode: first turn on the E8 Transmitter, then press the
"L4+" & "R3-" buttons at the same time, and hold down for 2S until the center indicator
turns from green to red, and the center indicator turns to green Flashes alternately with
red, indicating that the remote control has entered the binding mode.
3.
Check that when the blue light on the Tinyhawk III flight control board changes from
steady light to flashing, it means that the binding has been completed. Then press the
"L4+" & "R3-" buttons on the E8 Transmitter at the same time again, and the blue light
flashes again Turns to steady light, indicating that the binding has been completed.
4.
Unbinding: Unplug the battery of Tinyhawk III to power off and leave Bind Mode.
1.4 Mode switching
D8 mode: press the power switch and the "L1+" button at the same time: turn on and enter
D8 mode, then the mode indicator will turn solid red.(Emax recommends D8 mode)
D16 mode: press the power switch and the "L2-" button at the same time: turn on and
enter D16 mode, then the mode indicator light will turn solid green.
D16 LBT mode: Press the power switch and the "L4+" button at the same time: Turn on the
controller and enter D16 LBT mode, then the mode indicator light will turn solid yellow.
1.5 Gimbal Trim
Each joystick has a corresponding Trim button. Each Trim button adjusts the direction of the
corresponding joystick control. Each time it is adjusted, a beep will sound. When it is
adjusted to the center position, it will make a longer beep. Please pay attention to the
sound. With joysticks centered, use the Trim buttons until the drone is steadily hovering in
place.
1.6 Calibration of joystick
The E8 Transmitter is pre-calibrated, but recalibration can help solve some common issues:
1.
With the E8 Transmitter turned off, press the "L3-" button and the power button at the
same time as the controller turns on.
2.
Wait for the center indicator to light up and change from fast flashing to slow flashing,
and push the joysticks of E8 Transmitter to the maximum travel in the four directions up,
down, left, and right.
3.
Press the "L3-" button, the prompt will sound, exit the calibration mode, and the E8
Transmitter will then boot up.
1.7 Changing Transmitter Modes
Remove the screw and open the back cover of the E8 Transmitter housing. There is a
toggle switch on the left side of the board. Set the toggle switch to "L" (left-hand throttle
mode) or "R" (right-hand throttle mode), and swap the positions of the levers (the 6Pin
cable connecting the joystick to the main board does not need to change positions).
Left-handed mode: E8 Transmitter left stick, controls the throttle and yaw direction of
Tinyhawk III; E8 Transmitter right stick, controls Tinyhawk III's pitch and roll.
Right-handed mode: E8 Transmitter left stick controls the pitch and roll of Tinyhawk III; E8
Transmitter right stick controls the throttle and yaw direction of Tinyhawk III.
Schematic diagram of the left and right-handed joysticks (the picture shows the left-
handed mode, and of the joystick control reversed in the right-handed mode)
1.8 Trainer Port for Simulators
Insert one end of 3.5mm male to male into the trainer port (3.5mm audio interface), and
plug the other end into the simulator (sold separately) to output the corresponding
channel value.
Plug the micro USB cable into the remote control to output the corresponding channel
value.
1.9 Battery & Charging
The E8 Transmitter is compatible with a 18650 battery, with a working voltage of 4.3V-
3.3V. When you need to reinstall the battery, remove the battery compartment cover and
install the battery according to the correct polarity (the negative pole is on the spring side
of the battery compartment). Confirm that the battery compartment cover and the
battery compartment are perfectly matched then push forward until locked. If the battery
is not installed correctly, charging and starting cannot be performed correctly.
The remote control is charged with the micro USB at the bottom. After the USB cable is
inserted, the power charging indicator status:
When the indicator light is solid red: charging
Solid green indicator light: charging is full
Note: Use 5V-1A adapter for charging and micro USB cable for charging. When the
voltage is low (3.3V), it will alarm. Please charge when battery is low.
2.Transporter 2(with DVR)
2.1 Transporter 2
1.
Eye Adjustment Slots
2.
Frequency band switch button
3.
Channel switch button
4.
Video button
5.
Audio interface
Otros manuales para TINYHAWK III
1
Tabla de contenidos
Otros manuales de Cuadricóptero de Emax
