EMAC SBC-557 Manual de usuario
SBC-557
Half Size Super7 CPU Card
With LCD, Ethernet & SSD
Copyright Notice
This document is copyrighted, 1999. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in
this manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, nor for
any infringements upon the rights of third parties which may result
from its use.
Acknowledgements
AMD is a trademark of Advanced Micro Devices, Inc.
AMI is a trademark of American Megatrends, Inc.
Award is a trademark of Award Software International, Inc.
CyrixisatrademarkofCyrixCorporation.
IBM, PC/AT, PS/2, and VGA are trademarks of International
Business Machines Corporation.
Intel and Pentium II are trademarks of Intel Corporation.
Microsoft Windows®is a registered trademark of Microsoft Corp.
SMC is a trademark of Standard Microsystems Corporation.
RTLis a trademark of Realtek Semi-Conductor Co., Ltd.
C&T is a trademark of Chips and Technologies, Inc.
UMC is a trademark of United Microelectronics Corporation.
ITE is a trademark of Integrated Technology Express, Inc.
SiS is a trademark of Silicon Integrated Systems Corp.
VIA is a trademark of VIA Technology, Inc.
All other product names or trademarks are properties of their
respective owners.
PartNo. 2047557000 SBC-557 1st Edition
Prepared in Taiwan July 1999
A Message to the Customer
EMAC Customer Services
Each and every EMAC product is built to the most exacting
specifications to ensure reliable performance in the harsh and
demanding conditions typical of industrial environments. Whether
your new EMAC equipment is destined for the laboratory or the
factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name EMAC has
come to be known.
Your satisfaction is our primary concern. Here is a guide to
EMAC's customer services. To ensure you get the full benefit of
our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products.
So if you run into technical difficulties, we are here to help. For the
most frequently asked questions, you can easily find answers in
your product documentation. These answers are normally a lot
more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the
answer, gather all the information or questions that apply to your
problem, and with the product close at hand, call your dealer. Our
dealers are well trained and ready to give you the support you need
to get the most from your EMAC products. In fact, most problems
reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from EMAC
engineers every business day. We are always ready to give advice
on application requirements or specific information on the installa-
tion and operation of any of our products.
Product Warranty
EMAC warrants to you, the original purchaser, that each of its
products will be free from defects in materials and workmanship for
one year from the date of purchase.
This warranty does not apply to any products which have been
repaired or altered by persons other than repair personnel autho-
rized by EMAC, or which have been subject to misuse, abuse,
accident or improper installation. EMAC assumes no liability
under the terms of this warranty as a consequence of such events.
Because of EMAC's high quality-control standards and rigorous
testing, most of our customers never need to use our repair service.
If an EMAC product is defective, it will be repaired or replaced at
no charge during the warranty period. For out-of-warranty repairs,
you will be billed according to the cost of replacement materials,
service time, and freight. Please consult your dealer for more
details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For
example, CPU type and speed, EMAC products used, other
hardware and software used, etc.) Note anything abnormal and
list any on-screen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your
manual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA
(return material authorization) number from your dealer. This
allows us to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair
and Replacement Order Card and a photocopy proof of pur-
chase date (such as your sales receipt) in a shippable container.
A product returned without proof of the purchase date is not
eligible for warranty service.
5. Write the RMA number visibly on the outside of the package
and ship it prepaid to your dealer.
Packing list
Before you begin installing your card, please make sure that the
following materials have been shipped:
• 1SBC-557All-in-OneSingleBoardComputerCard
• 1Quick Installation Guide
• 1 Support CD contains the followings:
-- User's Manual (this manual in PDF file)
-- Ethernet drivers and utilities
--VGA drivers and utilities
• 1 hard disk drive (IDE) interface cable
• 1 floppy disk drive interface cable
• 1 6 pins mini-DIN dual outlet adapter for keyboard and PS/2
mouse
• 1 parallel port adapter (26 pins) and COM2 adapter (for RS-232/
422/485)
• 1 bag of screws and miscellaneous parts
If any of these items are missing or damaged, contact your distribu-
tor or sales representative immediately.
http://www.emacinc.com
Notice
DearCustomer,
Thank you for purchasing the SBC-557 board. This user's
manual is designed to help you to get the most out of the SBC-557,
please read it thoroughly before you install and use the board. The
product that you have purchased comes with an two-year limited
warranty, but EMAC will not be responsible for misuse of the
product. Therefore, we strongly urge you to first read the manual
before using the product.
To receive the lastest version of the user manual, please visit our
Web site at:
Contents
Chapter 1: General Information .......................1
Introduction ........................................................................... 2
Features.................................................................................. 3
Specifications ......................................................................... 4
Board layout........................................................................... 7
Board dimensions ................................................................. 8
Chapter 2: Installation .......................................9
Jumpers and connectors.................................................... 10
Locating jumpers ................................................................ 12
Locating connectors ........................................................... 13
Setting jumpers ................................................................... 14
CPU installing and upgrading............................................ 15
Install a CPU in the ZIF socket ..............................................15
Installing DRAM (DIMMs) .............................................. 17
System Memory ......................................................................17
Supplementary information about DIMM ...............................17
Memory Installation Procedures .............................................17
CPU Vcore select S1 (2~6)................................................ 18
Clear CMOS S1 (1)............................................................. 20
CPU clock select S2 (1~3)................................................. 21
CPU frequency ratio select S2 (4~6)................................ 22
CPU VIO select (J1) .......................................................... 23
LCD clock signal & driving voltage select (J3) ............ 24
DOC address select (J4) ................................................... 25
COM2 RS-232/422/485 select (J5, J6) ........................... 26
Level 2 cache select (J8)................................................... 27
IrDA connector (CN1, Pin 1~5)........................................ 28
Reset switch (CN1, Pin 6, 7) ............................................. 29
External / interal speaker (CN1, Pin 8~11)..................... 30
Hard drive LED (CN1, Pin 13, 14)................................... 31
IDE haed drive connector (CN2) ..................................... 32
Connecting the hard drive .......................................................33
IDE hard drive connector (CN2) ............................................33
CPU fan power connector (CN4) ...................................... 35
Display connectors (CN13, CN6) ..................................... 36
VGA display connector (CN13)..............................................37
LCD display connector (CN6) ................................................38
USB connector (CN7)......................................................... 39
Keyboard and PS/2 mouse connector (CN8, CN11)...... 40
Parallel port connector (CN9) ........................................... 42
Parallel port IRQ .....................................................................43
Parallel port connector table (CN9) ........................................43
Floppy drive connector (CN10) ........................................ 44
Connecting the floppy drive.....................................................45
Floppy drive connector (CN10)...............................................46
100Base-Tx Ethernet connector (CN14)........................ 47
Serial prots (CN15, CN12) ................................................ 48
Power connectors P8 & P9 (PWR1) ................................ 49
DiskOnChip socket (U19)................................................. 50
DiskOnChip (DOC) 2000 Installation ............................. 51
Chapter 3: Award BIOS Setup ..........................53
Starting setup....................................................................... 54
Setup keys............................................................................ 55
Getting help ......................................................................... 56
In case of problem...................................................................56
Main setup menu ................................................................ 57
Standard CMOS setup ....................................................... 58
BIOS features setup ........................................................... 66
CHIPSET features setup ................................................... 70
Power management setup.................................................. 73
PNP/PCI congfiguration setup .......................................... 77
Load BIOS defaults ............................................................ 80
Load setup defaults............................................................. 81
Integrated peripherals setup............................................. 82
Supervisor/User password setting ................................... 84
IDE HDD auto detection ................................................... 86
Save & exit setup................................................................ 87
Exit without saving ............................................................. 88
Chapter 4: Flat Panel/CRT controller Display
Drivers and Utilities ......................89
Software drives .................................................................... 90
Hardware configuration ..........................................................90
Necessary prerequisites ..........................................................92
Before you begin .....................................................................92
Windows 95 .......................................................................... 92
Driverinstallation ....................................................................92
Windows 3.1.......................................................................100
Driverinstallation ..................................................................100
OS/2..................................................................................... 101
Windows NT 3.51..............................................................103
Windows NT 4.0 ................................................................104
Driverinstallation ..................................................................104
Chapter 5: Ethernet Software configuration ...
.......................................................105
Ethernet software configuration ..................................... 106
Appendix A: Programming the Watchdog.........
Timer...........................................107
Programming the watchdog timer .................................. 107
How to program the Wtachdog Timer ..................................107
Demo program ......................................................................109
Appendix B: Installing PC/104 Modules ........111
Installing PC/104 modules............................................... 112
Tabla de contenidos
Otros manuales de Placa madre de EMAC
EMAC
EMAC MicroPac 535 Guía rápida de usuario
EMAC
EMAC PCM-5315 Manual de usuario
EMAC
EMAC PCM-6892E Manual de usuario
EMAC
EMAC SBC-675 Manual de usuario
EMAC
EMAC SoM-iMX6U Manual de usuario
EMAC
EMAC PCM-53E52 Manual de usuario
EMAC
EMAC PCM-5864 Manual de usuario
EMAC
EMAC PCM-4896 Manual de usuario
EMAC
EMAC PCM-4896L Manual de usuario
EMAC
EMAC PCA-6782 Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
