model M-SUBR10IC
high performance
model SUBR10IC
high performance
custom installed subwoofer
Speaker Wire Connections
to AMP500/1
Use screws provided to
mount the brackets to the
joists.
Grille Kit
Includes:
- Gasket
- Painted Screws
- Grille
Studs
Acoustic
Dampening
Foam Strips
Grille Slot
Brackets
Terminal Cup
General Maintenance.
If mounting in the floor, debris can end
up sitting on the subwoofer cone.
Occasionally remove the grille to
vacuum out the debris. Be careful not
to damage the speaker. Avoid spilling
water or other liquids into the grille and
onto the speaker. Use caution when
cleaning floors.
Warranty.
All Elura products come with a
limited liability warranty. This
warranty includes parts and labor
repairs on all components found to be
defective in material or workmanship
under normal conditions of use. This
warranty shall not apply to products
which have been abused, modified or
disassembled.
A speaker that fails under conditions
other than those covered will be re-
paired at the current price of parts and
labor in effect at the time of repair. Such
repairs are warranted for 90 days from
the day of reshipment to the BUYER. If
the unit is delivered by mail, customers
agree to insure the unit or assume the
risk of loss or damage in transit.
Under no circumstances will a unit be
accepted without a return authorization
number. The warranty is in lieu of all
other warranties expressed or implied,
including without limitations, any other
implied warranty or fitness or merchant-
ability for any particular purpose, all of
which are expressly disclaimed. Proof of
sale may be required in order to claim
warranty.
www.elura.audio
Specifications.
•Woofer: 10” Long Throw,
2” Voice Coil
• Impedance: 8Ω
• Sensitivity: 90 +/- 3 dB
• Freq. Response: 25 to 140 Hz
• Inputs: Gold Plated, Spring Loaded
Push Terminals
• Power Handling: 300 Watts
• Dimensions: 26.6” (675mm) L x
13” (330mm) W x 9.2” (233mm) D
• Weight: 34lbs
Speaker Placement.
The versatility of the Elura custom
installed subwoofer offers hidden
performance and opens up floor space.
The subwoofer installs in a standard
floor or ceiling joist construction. Take
note of the speaker connections before
mounting and wiring. Take precautions
to properly mount the speaker and
avoid obstacles commonly found inside
ceilings and floors. All hardware for
mounting and installation is included.
Installation Notes.
This subwoofer works best if mounted
using the correct hardware provided.
The SUBR10IC is a heavy product.
When installing overhead, have
a co-worker give you a hand. Avoid
choosing areas on the ceiling near
lights, wall sconces or other mounted
objects. Subwoofers can shake and
vibrate walls.
Pre-Construction Ceiling
& Floor Installations.
Attach the mounting brackets to each
corner of the subwoofer as shown.
Apply the additional sound deadening
foam strips to areas that may cause
unwanted noise. Mount the brackets to
the joists with the supplied screws.
Completely tighten down the screws to
avoid any vibrations. The SUBR10IC
comes with a 1/2” protective MDF
cover installed. This MDF cover can also
be used as a cut out template for the
white plastic grille. If the SUBR10IC is
installed before the drywall or flooring is
installed, leave the MDF cover installed
so that the installers can cut around the
MDF cover. After the drywall or flooring
is installed, remove the MDF cover and
install the white plastic and supplied
gasket, if necessary.
Retro Fit Ceiling
Installations.
If you are installing the SUBR10IC into a
finished ceiling or floor, first find a
suitable location away from light
fixtures, duct work, plumbing or
anything else that the subwoofer can
rattle/shake. Mark off the dimensions of
the SUBR10IC and protective MDF
cover using the supplied template to
locate the grille opening. Remove the
MDF cover and utilize it as a cut out
template for the grille. Attach the
mounting brackets to each corner of the
subwoofer as shown. Apply the
additional sound deadening foam strips
to areas that may cause unwanted
noise. Mount the brackets to the joists
with the supplied screws. Completely
tighten down the screws to avoid any
vibrations. Install the white plastic grille
and the supplied gasket if necessary.
MSTR
