Elu ELU27158 Manual de usuario

The Model and Serial No. plate is located on the main

housing of the tool. Record these numbers in the

spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. _______________________________________

IMPORTANT

Please make certain that the person who is to use

this equipment carefully reads and understands these

instructions before starting operations.

1/2" Drill

ELU27158

Read and understand all warnings and operating instructions

before using any tool or equipment. When using tools or equipment, basic

safety precautions should always be followed to reduce the risk of personal

injury. Improper operation, maintenance or modification of tools or equipment

could result in serious injury and property damage. There are certain

applications for which tools and equipment are designed. Elu strongly

recommends that this product NOT be modified and/or used for any application

other than for which it was designed.

Information regarding the safe and proper operation of this tool is available from

the following sources:

Power Tool Institute

1300 Sumner Avenue, Cleveland, OH 44115-2851

National Safety Council

1121 Spring Lake Drive, Itasca, IL 60143-3201

American National Standards Institute, 25 West 43rd Street, 4 floor, New York,

NY 10036 www.ansi.org ANSI 01.1Safety Requirements for Woodworking

Machines, and the U.S. Department of Labor regulations www.osha.gov

SAVE THESE INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .1

SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . .5

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS

Some dust created by power sanding, sawing, grinding, drilling,

and other construction activities contains chemicals known (to the

State of California) to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based paints

• crystalline silica from bricks and cement and other masonry products

• arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often you do this type

of work. To reduce your exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, always wear NIOSH/OSHA

approved, properly fitting face mask or respirator when using such tools.

indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

indicates a potentially hazardous situation which, if not

avoided,could result in death or serious injury.

indicates a potentially hazardous situation which, if not

avoided,may result in minor or moderate injury.

used without the safety alert symbol indicates potentially

hazardous situation which, if not avoided, may result in

property damage.

CALIFORNIA PROPOSITION 65

It is important for you to read and understand this manual. The

information it contains relates to protecting YOUR SAFETY and

PREVENTING PROBLEMS. The symbols below are used to help

you recognize this information.

SAFETY GUIDELINES - DEFINITIONS

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while operating a power

tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Grounded tools must be plugged into an outlet properly installed and

grounded in accordance with all codes and ordinances. Never remove the

grounding prong or modify the plug in any way. Do not use any adaptor plugs.

Check with a qualified electrician if you are in doubt as to whether the outlet is

properly grounded. If the tools should electrically malfunction or break down,

grounding provides a low resistance path to carry electricity away from the

user. Some units are grounded. Applicable only to Class I (grounded) tools.

• Double insulated tools are equipped with a polarized plug (one blade is

wider than the other.) This plug will fit in a polarized outlet only one way. If

the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,

contact a qualified electrician to install a polarized outlet. Do not change the

plug in any way. Double insulation eliminates the need for the three wire

grounded power cord and grounded power supply system. Applicable only to

Class II (double insulated) tools. Some units are rated at 230 volts and they

are fitted with the 220 volt style plug which is not polarized.

• Avoid body contact with grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your

body is grounded.

• Don’t expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug

from an outlet. Keep cord away from heat, oil, sharp edges or moving parts.

Replace damaged cords immediately. Damaged cords increase the risk of

electric shock.

• When operating a power tool outside, use an outdoor extension cord

marked “W-A” or “W.” These cords are rated for outdoor use and reduce the

risk of electric shock. When using an extension cord, be sure to use one heavy

enough to carry the current your product will draw. An undersized cord will

cause a drop in line voltage resulting in loss of power and overheating. The

following table shows the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next heavier gage. The smaller

the gage number, the heavier the cord.

Read and understand all instructions. Failure

to follow all instructions listed below may result in electric shock,

fire and/or serious personal injury.

GENERAL SAFETY RULES

GENERAL SAFETY RULES continued

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use tool while tired or under the influence of

drugs, alcohol, or medication. A moment of inattention while operating power

tools may result in serious personal injury,

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose clothing,

jewelry, or long hair can be caught in moving parts. Air vents often cover

moving parts and should also be avoided.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying

tools with your finger on the switch or plugging in tools that have the switch on

invites accidents.

• Remove adjusting keys or switches before turning the tool on. A wrench

or key that is left attached to a rotating part of the tool may result in personal

injury.

• Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid

safety shoes, hard hat, or hearing protection must be used for appropriate

conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece

to a stable platform. Holding the work by hand or against your body is

unstable and may lead to loss of control.

• Do not force tool. Use the correct tool for your application. The correct tool

will do the job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be

controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any

adjustments, changing accessories, or storing the tool. Such preventative

safety measures reduce the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons.

Tools are dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools, with sharp cutting edges are less likely to bind and are

easier to control.

• Check for misalignment or binding of moving parts, breakage of parts,

and any other condition that may affect the tools operation. If damaged,

have the tool serviced before using. Many accidents are caused by poorly

maintained tools.

• Use only accessories that are recommended by the manufacturer for

your model. Accessories that may be suitable for one tool, may become

hazardous when used on another tool.

1. Hold tool by insulated gripping surfaces when performing an operation

where the cutting tools may contact hidden wiring or its own cord. Contact

with a “live” wire will make exposed metal parts of the tool “live” and shock

the operator.

2. Keep handles dry, clean, free from oil and grease. It is recommended to

use rubber gloves. This will enable better control

3. DO NOT TOUCH ANY METAL PARTS OF THE TOOL when drilling or

driving into walls, floors or wherever live electrical wires may be

encountered. Hold the tool only by insulated grasping surfaces to prevent

electric shock if you drill or drive into a live wire.

4. Wear eye and hearing protection. Always use safety glasses. Everyday

eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY

EQUIPMENT. Eye protection equipment should comply with ANSI Z87.1

standards. Hearing equipment should comply with ANSI S3.19 standards.

5. Use of this tool can generate and disburse dust or

other airborne particles, including wood dust, crystalline silica dust

and asbestos dust. Direct particles away from face and body. Always

operate tool in well ventilated area and provide for proper dust removal.

Use dust collection system wherever possible. Exposure to the dust may

cause serious and permanent respiratory or other injury, including silicosis

(a serious lung disease), cancer, and death. Avoid breathing the dust, and

avoid prolonged contact with dust. Allowing dust to get into your mouth

or eyes, or lay on your skin may promote absorption of harmful material.

Always use properly fitting NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure, and wash exposed areas with soap

and water.

ADDITIONAL SPECIFIC SAFETY RULES

GENERAL SAFETY RULES continued

SERVICE

• Tool service must be performed only by qualified repair personnel.

Service or maintenance performed by unqualified personnel could result in a

risk of injury.

• When servicing a tool, use only identical replacement parts. Follow

instructions in the Maintenance section of this manual. Use of unauthorized

parts or failure to follow Maintenance Instructions may create a risk of electric

shock or injury.

SAVE THESE INSTRUCTIONS!

MOTOR

Many tools will operate on either D.C., or single phase 25 to 60 cycle A.C.

current and voltage within plus or minus 5 percent of that shown on the

specification plate on the tool. Several models, however, are designed for A.C.

current only. Refer to the specification plate on your tool for proper voltage and

current rating.

Do not operate your tool on a current on which the voltage is not

within correct limits. Do not operate tools rated A.C. only on D.C. current. To do

so may seriously damage the tool.

SYMBOL DEFINITION

V ..........................................volts

A ..........................................amperes

Hz ........................................hertz

W ........................................watts

min ......................................minutes

........................................alternating current

....................................direct current

no ........................................no load speed

........................................Class II Construction

........................................earthing terminal

........................................safety alert symbol

.../min ..................................revolutions per minute

EXTENSION CORD SELECTION

If an extension cord is used, make sure the conductor size is large enough to

prevent excessive voltage drop which will cause loss of power and possible

motor damage. A table of recommended extension cord sizes will be found in

this section. This table is based on limiting line voltage drop to 5 volts (10 volts

for 230 volts) at 150% of rated amperes.

If an extension cord is to be used outdoors, it must be marked with the suffix

W-A or W following the cord type designation. For example – SJTW-A to indicate

it is acceptable for outdoor use.

RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS

Length of Cord in Feet

115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft.

230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft.

0-2 18 18 18 16 16 14 14 12 12

2-3 18 18 16 14 14 12 12 10 10

3-4 18 18 16 14 12 12 10 10 8

4-5 18 18 14 12 12 10 10 8 8

5-6 18 16 14 12 10 10 8 8 6

6-8 18 16 12 10 10 8 6 6 6

8-10 18 14 12 10 8 8 6 6 4

10-12 16 14 10 8 8 6 6 4 4

12-14 16 12 10 8 6 6 6 4 2

14-16 16 12 10 8 6 6 4 4 2

16-18 14 12 8 8 6 4 4 2 2

18-20 14 12 8 6 6 4 4 2 2

Nameplate Ampere Rating

SAVE THESE INSTRUCTIONS!

MOTOR BRUSHES

ELU uses an advanced brush system which automatically stops the drill when

the brushes wear out. This prevents serious damage to the motor.

FUNCTIONAL DESCRIPTION

Fig. 1

SWITCH

To start drill, depress trigger switch; to stop

the drill, release trigger. To lock trigger in the

on position for continuous operation, depress

trigger and push up locking button “A” shown

in figure 1, then gently release the trigger. To

release the locking mechanism, depress the

trigger fully, then release it. Before using the

tool each time, be sure that the locking

button release mechanism is working freely.

Do not lock the switch on when drilling by

hand so that you can instantly release the

trigger switch if the bit binds in the hole.

The locking button is for use only when the drill is mounted in a drill press stand

or otherwise held stationary.

Be sure to release the locking button before disconnecting the plug from the

power supply. Failure to do so will cause the tool to start immediately the next

time it is plugged in. Damage or injury could result.

SWITCH

ASSEMBLY

LOCK-OUT KEY

THE VARIABLE SPEED TRIGGER SWITCH

This switch permits speed control: the farther the trigger is depressed, the higher

the speed of the drill.

NOTE: Use lower speeds for starting holes without a center punch, drilling in

metal or plastics, driving screws or drilling ceramics. Higher speeds are better for

drilling wood and composition boards, and for using abrasive and polishing

accessories.

THE REVERSING LEVER

The reversing lever changes the direction of

rotation of the drill and is used when backing

out screws and jammed drill bits. To operate

the tool in reverse, release the trigger switch

and push the lever to the left (when viewed

from the chuck end) as shown in Figure 2. To

operate the drill in forward for drilling holes or

driving screws (as well as when using other

accessories) release the trigger switch and

push the lever to the right (when viewed from

the chuck end).

Return the reversing lever to the forward

position after all operations in reverse are

completed.

SWITCH LOCK-ON

Your drill is equipped with a switch lock-on feature. If you wish to disable this

feature, take your tool to any authorized service center. The service center can

provide a lock-out key to prevent the unit from being locked in the on position

(Figure 3).

REVERSING

LEVER

(Shown in

Forward Position)

Fig. 2

Fig. 3

Tabla de contenidos

Otros manuales de Perforar de Elu

Elu

Elu SBA 91 Manual de usuario

Elu

Elu BSA34 Manual de usuario

Manuales populares de Perforar de otras marcas

Makita

Makita BDF456 Manual de usuario

Black & Decker

Black & Decker LDX220 Manual de usuario

Hitachi

Hitachi DH 40MA Manual de usuario

Challenge

Challenge JO Manual de referencia técnica

Makita

Makita LXFD01 Manual de usuario

Festool

Festool T18+3 Manual de usuario

Milwaukee

Milwaukee M12 FPDX-202X Manual de usuario

EINHELL

EINHELL TE-RH 32 E Manual de usuario

Makita

Makita DHP484 Manual de usuario

Makita

Makita FD05 Manual de usuario

Bosch

Bosch PSB 530 RA Manual de usuario

Maximum

Maximum 054-1359-4 Manual de usuario

Makita

Makita HP332D Manual de usuario

Raider

Raider RDP-HD31H Manual de usuario

Bort

Bort BPM-1400x2 Manual de usuario

Black & Decker

Black & Decker 7266 Manual de usuario

KENT USA

KENT USA TRD1230 Manual de usuario

Bosch

Bosch GSB 19-2 RE Manual de usuario