Elsys ELT-2 Manual de usuario

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Specifications in this document are subject to change without notice.

©Elektroniksystem i Umeå AB 2020

www.ime.de

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Important safety information

Read this manual before attempting to install the device!

Failure to observe recommendations included in this manual may be

dangerous or cause a violation of the law. The manufacturer, Elektroniksystem i

Umeå AB will not be held responsible for any loss or damage resulting from not

following the instructions of this operating manual.

•The device must not be dismantled or modified in any way.

•The device is not intended to be used as a reference sensor, and

Elektroniksystem i Umeå AB will not be held liable for any damage which

may result from inaccurate readings.

•The battery should be removed from the device if it is not to be used for

an extended period. Otherwise, the battery might leak and damage

the device. Never leave a discharged battery in the battery

compartment.

•The device must never be subjected to shocks or impacts.

•To clean the device, wipe with a soft moistened cloth. Use another soft,

dry cloth to wipe dry. Do not use any detergent or alcohol to clean the

device.

Disposal note in accordance with ElektroG and WEEE Directive

2012/19/EU

The device, as well as all the individual parts, must not be disposed of

with household waste or industrial waste. You are obliged to dispose of the

device at the end of its service life in accordance with the requirements of

ElektroG in order to protect the environment and to reduce waste through

recycling. For additional information and how to carry out disposal, please

contact the certified disposal service providers. The sensors contain a lithium

battery, which must be disposed of separately.

www.ime.de

 
3 
Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden 
E-mail: suppo[email protected] ǀWeb: www.elsys.se 
Contents 
 
Important safety information.......................................................................................................... 2 
Description......................................................................................................................................... 5 
Main features of ELT-2 HP........................................................................................................ 6 
Installation.......................................................................................................................................... 7 
Installing external sensors ......................................................................................................... 8 
External temperature sensor................................................................................................ 8 
Analog input 0 –3 or 0 –10 Voltage............................................................................... 8 
Powered analog input 0 –10V........................................................................................... 9 
Switch Input (Pull up) ........................................................................................................... 9 
Pulse count (Pull up) ..........................................................................................................10 
Pulse count (Pull down) .....................................................................................................10 
Pulse count (Pull down) –External pulse.......................................................................11 
Pulse count (Pull up) –S0 input ......................................................................................11 
4 –20 mA input...................................................................................................................12 
Water leak input....................................................................................................................12 
Maxbotix distance sensor input.........................................................................................13 
Meter (Decagon) sensor input .........................................................................................13 
Pulse count (Pull up) –2 channels..................................................................................14 
Pulse count (Pull down) –2 channels ............................................................................14 
Switch input + Temperature sensor.................................................................................15 
Sensor configuration......................................................................................................................16 
NFC Configuration.....................................................................................................................16 
Over the air configuration ........................................................................................................17 
Application parameters.............................................................................................................17 
Sensor behavior..............................................................................................................................17 
www.ime.de

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

NFC Read / Write ......................................................................................................................17

Sensor startup ...........................................................................................................................18

Sampling mode / Periodic measurement .............................................................................19

Schedule Transmission.............................................................................................................19

External sensors ........................................................................................................................20

Specifications ..................................................................................................................................21

Sensor payload format .............................................................................................................21

Regulations......................................................................................................................................22

Legal Notices .............................................................................................................................22

Declaration of conformity ........................................................................................................22

www.ime.de

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Description

ELT-2 is a universal outdoor device for LoRaWAN® wireless network. It is

designed to be in extreme conditions and can measure analog or digital signals.

Use it together with electricity meters, flow meters, analog sensors, moisture

sensors and other external sensors. ELT-2 is enclosed in an IP67 box and have

four internal sensors: temperature sensor, humidity sensor, accelerometer and an

atmospheric pressure sensor. This is a battery-powered device equipped with

NFC (Near Field Communication) and can easily be configured from a

smartphone.

The barcode contains DevEUI and sensor type. This label is located at the back

of your device,

ELT-2-HP

www.ime.de

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Main features of ELT-2

•Compatible with LoRaWAN® specification 1.0.3

•Measures ambient temperature

•Measures ambient humidity

•Measures ambient atmospheric pressure

•Detects acceleration

•Analog 0 –10 V input

•Digital input

•Direct connection to various external sensors and equipment

•Easy installation

•Easy configuration

•IP67 Classified

•Battery-powered

•Long-range communication

•Configurable over NFC

•Configurable over the air

•Ten years of battery life*

•Supported channel plans: US902-928, EU863-870, AS923, AU915-

928, KR920-923, RU864, IN865 & HK923

•CE Approved and RoHS compliant

*Depending on settings and environmental factors

www.ime.de

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Installation

1. Remove the front lid of the sensor by removing the four screws.

2. Install the battery. The ELT-2 requires one AA battery. The battery type

is 3.6V Lithium Battery (ER14505).

Caution: Using batteries other than the ones provided may result in loss of performance

and battery life, and also damage to the device. Dispose of properly, observing

environmental protection rules.

3. Connect any eventual external sensors.

4. Close the lid and tighten the screws carefully. Make sure that the cable

gland and antenna connection is tightened to prevent ingress of

moisture.

5. Mount the device by using the two holes on the sides.

www.ime.de

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Installing external sensors

External temperature sensor

Configured for 1-wire interface. Connect a DS18B20 compatible sensor. Select

“Temperature sensor 1 wire” in the application “Sensor Settings”. ELT input is internally

pulled up by 2.2kΩ.

Analog input 0 –3 or 0 –10 Voltage

Input signal between input and ground.

Select “Analog input 0-3V” or ”Analog input 0 – 10V” in the application “Sensor

Settings”. ELT input is internally pulled down.

/ 0-10V

www.ime.de

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Powered analog input 0 –10V

Input signal between input and ground. +3V present at B+ pin.

Select “Analog input” in the application “Sensor Settings”. Select “Eternal startup time”

and configure ON-time for sensor. External startup time is how long the sensor will be

powered before sampling value. ELT input is internally pulled down and the input

impedance is 7.4 kΩ

Switch Input (Pull up)

Input signal between input and ground.

Select “Switch (Normally open)” in the application “Sensor Settings”. ELT input is

internally pulled up by ~50 k Ω*.

www.ime.de

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Pulse count (Pull up)

Input signal between input and ground.

Select “Pulse input (pull up)” in the application “Sensor Settings”. ELT input is internally

pulled up by ~50 k Ω*.

Pulse count (Pull down)

Input signal between input and B+.

Select “External startup time” in the application “Sensor Settings” and configure ON-time

for always on that is >1000000ms.

Select “Pulse input(pull down)”. ELT input is internally pulled down by ~50 kΩ*.

www.ime.de

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de Elsys

Elsys

Elsys ERS CO2 Manual de usuario

Elsys

Elsys ERS Manual de usuario

Elsys

Elsys EMS Desk Manual de usuario

Elsys

Elsys ERS2 Series ERS2 Lite Manual de usuario

Elsys

Elsys ECO Series Manual de usuario

Elsys

Elsys EMS Door Manual de usuario

Elsys

Elsys ERS Manual de usuario

Elsys

Elsys EMS Series Manual de usuario

Elsys

Elsys ELT-2 HP Manual de usuario

Elsys

Elsys ERS Eye Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario