Elo Touch Solutions E062324 Manual de usuario
© Copyright 2017 Elo Touch Solutions, Inc. 1
QIG600042 REV. A
E062324 ELO-STAND-SELF-SERVICE-DESKTOP
E062510 ELO-STAND-SELF-SERVICE-FLOOR EXT
E062704 KIT-EMV-CRADLE-VF-MX915-ING-ISC250
E062899 KIT-EMV-INGENICO IPP350 CRADLE-SS
ASSEMBLY INSTRUCTIONS, ELO SELF SERVICE STAND
© Copyright 2017 Elo Touch Solutions, Inc. 2
QIG600042 REV. A
Contents for kit:
E062324 ELO-STAND-SELF-SERVICE-DESKTOP Bag A:
SCREW, M4X10, ROUND-HEAD,
FLANGE, HEX
Qty. 2
Bag B:
SCREW, M4X10, FLAT-HEAD, HEX
Qty. 4
Bag C:
SCREW, M3X8, PAN-HEAD,
CROSS-RECESS
Qty. 3
Tie-wrap
Qty. 2
© Copyright 2017 Elo Touch Solutions, Inc. 3
QIG600042 REV. A
Remove and save (2) screws on
rear of stand with provided hex
wrench, pull out printer tray.
Add (2) screws from bag “A”;
leave ~3mm (1/8”) gap for stand.
Gap
Align slots on bottom rear of stand with (2) screws on base and
slide on stand. Add (4) screws from bag “B”. Tighten (2) screws at
rear.
For Floor Stand, go to step 4
For Countertop Stand, continue to step 2Continue to step 12 for Countertop Stand
1 2
3
© Copyright 2017 Elo Touch Solutions, Inc. 4
QIG600042 REV. A
Assemble base plate to tower
using (6) screws from bag “K”.
Remove and save (4) hex-head screws on
the left and right of the stand with provided
hex wrench. Pull off the silver cover and set
aside.
Continue to step 6for Floor Stand
54
© Copyright 2017 Elo Touch Solutions, Inc. 5
QIG600042 REV. A
Add (2) screws from bag “A”;
leave ~3mm (1/8”) gap for stand.
Gap
Align slots on bottom rear of stand with (2) screws
on base and slide on stand. Add (4) screws from
bag “B”. Tighten (2) screws at rear.
Continue to step 8for Floor Stand
76
© Copyright 2017 Elo Touch Solutions, Inc. 6
QIG600042 REV. A
Add power strip brackets (supplied with
power strip) using (2) screws from bag
“L”. Hook one side of power strip onto
brackets than push to snap down.
Add power bricks into tower
using provided straps.
Continue to step 10 for Floor Stand
9
8
© Copyright 2017 Elo Touch Solutions, Inc. 7
QIG600042 REV. A
(2) bolt holes available on top of base to
secure stand to floor. Feet can be adjusted
in case of uneven surfaces.
Replace floor stand cover and secure
using (4) screws saved from step 4.
Continue to step 12 for Floor Stand
11
10
© Copyright 2017 Elo Touch Solutions, Inc. 8
QIG600042 REV. A
Remove and save (2) hex-head screws using provided
hex wrench. Open display mount and support with kick-
stand. Kick-stand
Assemble (2) screws from bag “I” to
top VESA mount hole on back of I-
Series. Assemble display to top
slotted holes on stand bracket. Add
remaining (2) screws to bottom VESA
mount
Assemble bottom (2) VESA
mount screws from back
side.
For adding EMV Mount to Desk/Floor Stand, go to step 15
For NO EMV Mount, continue to step 13 Continue to step 14
1312
© Copyright 2017 Elo Touch Solutions, Inc. 9
QIG600042 REV. A
Route needed cables from I-Series
through stand.
Add tie-wrap
Continue to step 31 for Countertop Stand
14
© Copyright 2017 Elo Touch Solutions, Inc. 10
QIG600042 REV. A
Assemble iPP350 to bracket using hook
on bracket and (2) screws from bag “J”.
For Ingenico iPP350 EMV Cradle (E062899), go to
step 15
For Verifone MX915 /Ingenico iSC250 EMV Cradle
(E062704), go to step 23
Add cable to iPP350.
Add tie-wraps
Route terminal cable through bracket.
15
16
Este manual sirve para los siguientes modelos
3
Otros manuales de Terminal de pago de Elo Touch Solutions
Manuales populares de Terminal de pago de otras marcas
Ingenico
Ingenico iWL250B Manual de usuario
Optimum
Optimum M4230 Manual de usuario
Triton
Triton RL5000 Manual de usuario
Ingenico group
Ingenico group Lane/8000 Manual de usuario
Gilbarco
Gilbarco FlexPay IV CRIND Manual de instalación y operación
Infinite Peripherals
Infinite Peripherals Infinea Tab Lite Manual de usuario
