Elite Technology ET Series Manual de usuario
Elite Technology
ET Series DVR
User Guide
Electronics Line Site (DVR)
Electronics Line Center (Remote)
2
3
Contents
Electronics Line Site
•Main Screen 5
•Entering Setup mode 9
•Hardware Setup 10
oCamera Setup 11
oSensor Setup 13
oControl Setup 14
oExternal Monitor 16
•Motion Setup 17
oSetup for Individual Cameras 17
oSetup for All Cameras 21
•Schedule Setup 23
oRecord Modes 23
oHow to set schedule 24
oSet Holiday 26
oSimple / Advanced Mode 27
•Screen Division 28
•Modem Setup 29
oUsing the “Ping” utility 32
oConfiguring the modem 35
•Site Information 41
•Password Setup 46
•Audio Setup 48
oMicrophone and Speaker Setup 49
•System Setup 55
oBackup Settings 56
oCreating a Backup Schedule 58
oAdding Backup Media 60
oRemote Backup Media 61
oEasy Update 64
•Motion Tracking Setup 68
•Storage Setup 72
•E-Map Setup 74
oCamera 76
oControl 77
oSensor 78
•Pan Tilt Zoom Control 80
4
Contents
Electronics Line Site
•Search Mode 82
oCalendar 82
oRecorded Data Timeline 84
oStill Image Tools 85
oSearch Tools 86
oPlayback Controls 87
oIndex Search 88
oSearch Option Panel 89
oPrinting an Image 90
Installing a local Printer 91
Installing a Network printer 93
oBackup 94
Floppy Backup 95
Watermark Checker 95
Time Backup 96
AVI Backup 97
Select Media 98
oFormatting CD-R/CD-RW disks 100
Main Screen
Screen Division Selections
Select the number of cameras you wish to view on the main screen.
Choose 4, 6, 9, 10, 13, or 16 camera splits
The cameras that will appear in each view are assignable in setup under “Screen Division”
Full Screen View
This button will set the main screen to “Camera only” view. The GUI (Graphic User
Interface) which includes the Screen Division buttons, the Event Indicators, the Clock,
Setup and Search buttons, Power button, etc. will be hidden.
Right click on the screen to return to normal view.
Camera, Sensor, and Control Relay Event Indicators
Each numbered button corresponds to the similarly numbered device in each category.
Camera indicators will flash when a camera detects motion. Sensor indicators will flash
when a device (Glass break or motion detector) is tripped.
Control indicators will flash when a relay (Alarm, siren, strobe, etc.) has been activated.
Control relays may also be manually activated by left clicking on the indicator. Click on it
again to deactivate.
Screen
Division
Selections
Camera, Sensor,
and Control
Relay Event
Indicators
Full
Screen
View
6
Main Screen
Clock
Indicates current date and time
Quad Rotation Mode
Sets main view to 4 camera split and rotates view continuously through all active cameras
starting with 1~4, then 5~8, then 9~12, then 13~16, then back to 1~4, etc.
Click on an image, or select a Screen division button to stop rotation and return to normal
mode.
Setup and Search Mode
Left click to enter Setup (Camera selection, Screen division, Schedule, Audio, Motion, etc.)
or Search Mode (Review and backup recorded data)
Storage Indicator
Top line shows total Hard Drive space allocated and available for data storage.
Numbers in the blue box show Hard Drive space that has been used for data storage in
Megabytes and Percentage of free space remaining. When percentage of free space reaches
0%, the DVR has used all available storage and will begin to overwrite (replace) the oldest
recorded data.
(It is normal for the ‘Free Space’ indicator to read ‘0% Free’ once the DVR has started
overwriting the oldest data. This number will not change unless you reallocate (erase) the
storage drive.)
Clock
Quad
Rotation
Mode
Setup and
Search
Mode
Storage
Indicator
7
Main Screen
Main View Screen
This is where the live images from your cameras will appear.
Left click on any image to bring it to full screen view. Left click on the image again to
return to normal view.
Mode Indicator
Mode indicator will indicate whether you are in Display, Search, or Pan /Tilt mode.
Power Button
Left click on the power button in Display mode to turn off the DVR.
Unit will stop recording and turn itself off. Use the Power switch (on the front of the DVR)
to restart the unit.
Main View
Screen
Mode
Indicator
Power
Button
8
Setup
Your new Elite Technology ET-Series DVR is “Ready to Go” right out of the box.
It is factory preset to start up and begin recording data without any effort on your part.
Just hook up your cameras and turn it on.
In order to fine tune your installation and customize the DVR to get the best performance
for your particular situation, or to setup extra features such as Pan/Tilt/Zoom cameras,
Sensors and Control relays, Record mode quality and scheduling, Custom screen divisions,
etc., the Elite Technology ET-Series is equipped with an extensive array of options
available through the “Setup” mode.
Left click on the “Setup” button to enter Setup mode.
Left click
to enter
Setup
9
Setup
When you click on setup for the first time you will be prompted to enter a
password.
Leave the user level set to Level 1 (Administrator) and use the keyboard to enter a 4 digit
numeric password (4 characters, all numbers). You may left click on the numbers on the
‘Virtual Keypad’ if no keyboard is available.
You may also press “Enter” on your keyboard or click on “OK” with the left mouse button
if you want no password set up at this time. (You can change this later in the “Password
Setup” section.)
You will then be asked if you want to create the default user database.
Click on “Yes” or press “Enter” on your keyboard to continue.
You will then be prompted to “Confirm” or, re-enter your password again to gain entry to
Setup mode.
Remember your password!
Once you have created the password database you will not be able to access Setup or
Search mode without it.
Virtual
Keypad
10
Hardware Setup
When you enter Setup mode you can access all of the functions of the DVR and customize
settings for your installation to achieve the best performance of your unit in any
environment.
Most key functions (Camera types, color settings, motion settings, frame rates, etc.) can be
set up on an individual camera by camera basis.
The Setup mode is organized on several “Pages” accessed by the tabs at the top of the
panel. Left click with the mouse on any tab to access that page. The first page that appears
is the “Hardware Setup” page.
Click on a tab to
select a Setup Page
Tabla de contenidos
