Eliminator Lighting Electro Panel 192 Manual de usuario

Electro

Panel 192

SPECIFICATIONS:

Model: Electro Panel 192

LEDs: 192 - 64 Red, 64 Green,

& 64 Blue

Weight: 4.6lbs./ 2.1kgs.

Size: 7.12” (H) x 12.41” (W) x

4.5” (D)

Fuse: 2 Amp

Supply Voltage: 120V

Working Position: Any Safe position

Duty Cycle: None

DMX Channels: 6 DMX Channel Modes:

1, 2, 3, 4, 6, or 7 DMX

Channels

Colors: Multiple Colors

Warranty: 1 Year

CAUTION! Please read and

understand these instructions

before installing or operating

this unit.

Operating Instructions:

The Electro Panel 192 has been tested at the

factory, there is no assembly required. The

unit is ready to be plugged into a power out-

let. This unit is a 7 channel DMX intelligent

LED par can. It can be run as a stand-alone,

static unit DMX controlled unit, or in a Master/

Slave configuration. While in Stand Alone or

a Master/Slave configuration, you can run

the auto mode. For stand-alone mode, and

Master/Slave configuration settings, see other

side.

©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com

Caution! Never open unit when in use.

Always disconnect main power before

replacing fuse. Remember to always

replace with the exact same type fuse.

1 Year Limited Warranty: Eliminator Lighting warranty is valid from the date of purchase. Our

1 year limited warranty covers manufacturing defects only. Serial number, place of purchase with

dated valid receipt must be submitted at time of service. Eliminator Lighting warranty does not cover

items or parts prone to wear and tear: lamps, fuses, brushes and belts. Eliminator Lighting warranty

is only valid with-in the United States.

ADDR - DMX Address Setting.

1. Tap the either the MENU, UP, or DOWN buttons until “ADDR” is displayed, press ENTER.

2. “1” will now be displayed and ashing. Press the UP or DOWN buttons to nd your desired

address. Press ENTER to set your desired DMX address.

CHND - There are 6 DMX Channel modes to choose from, this will let you switch and select

your DMX Channel mode. You can choose from either 1, 2, 3, 4, 6, or 7 DMX Channels. Please

see the last page of the DMX values and traits for each DMX Channel Mode.

1. Tap the either the MENU button until “CHND” is displayed, press ENTER.

2. Tap the UP or DOWN buttons to scroll through the different DMX Channel modes. Once you have

found your desired DMX Channel mode press ENTER to conm and exit.

SLND - This will let you set unit as a master or slave in a master/slave conguration.

1. Tap the either the MENU button until “SLND” is displayed, press ENTER. “MSTR”, “SL 1” or “SL 2” will

be displayed.

2. Tap the UP or DOWN buttons until your desired setting is displayed, press ENTER to conm and

exit.

SHND - in this mode you can choose and run one of 11 preprogrammed shows.

1. Tap the either the MENU button until “SHND” is displayed, press ENTER.

2. Tap the UP or DOWN buttons to scroll through 11 preprogrammed shows.

3. Select your desired show by pressing the ENTER button to conrm and exit.

DIMM - in this mode you can set the brightness/intensity of the xture.

1. Tap the either the MENU button until “DIMM” is displayed, press ENTER.

2. Tap the UP or DOWN buttons to adjust the brightness (0-255). A setting of 0 will not produce any

light output

3. Select your desired intensity by pressing the ENTER button to conrm and exit.

STRO - in this mode you can activate and set the strobe rate.

1. Tap the either the MENU button until “STRO” is displayed, press ENTER.

2. Tap the UP or DOWN buttons to adjust the stobe rate (0-255). A setting of 0 will deactivate the

strobe feature.

3. Select your desired strobe rate by pressing the ENTER button to conrm and exit.

BLND - Blackout or Stand by mode.

1. Tap the either the MENU button until “BLND” is displayed, press ENTER. Either Yes or No will be

displayed.

©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com

2. To activate Blackout tap the UP or DOWN buttons until Yes is displayed, press ENTER to conm

and exit. The xture will now be in Blackout mode. To deactivate Blackout mode, select No and

press Enter.

LED - With this function you can switch the lamp on or off via the control board.

1. Tap the either the MENU button until “LED” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to switch

on the LED, or “OFF” to switch off the LED.

3. Press ENTER to conrm and exit.

I DSP - This function will reverse the display 180º.

1. Tap the either the MENU button until “I DSP” is displayed, press ENTER.

2. Tap the UP button until “FLIP” is displayed.

3. Press ENTER, the display will show “ON/OFF”.

4. Press the UP button to select “ON” to activate this function, or “OFF” to deactivate this function.

5. Press ENTER to conrm.

FHRS - With this function you can display the running time of the unit.

1. Tap the either the MENU button until “FHRS” is displayed, press ENTER.

2. The display shows the running time of the unit. Press MENU to exit.

VER - Use this function to display the Software version of the unit.

1. Tap the either the MENU button until “VER” is displayed, press ENTER.

2. The display will show the software version.

©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com

Tabla de contenidos

Otros manuales de Equipo de iluminación de Eliminator Lighting

Eliminator Lighting

Eliminator Lighting Decor XV Manual de usuario

Eliminator Lighting

Eliminator Lighting INDY HEX PAR Manual de usuario

Eliminator Lighting

Eliminator Lighting Trio Par LED RG Manual de usuario

Eliminator Lighting

Eliminator Lighting MBDMX-PLUS Manual de usuario

Eliminator Lighting

Eliminator Lighting INDY HEX PAR Manual de usuario

Eliminator Lighting

Eliminator Lighting MEGA FLAT HEX PAK Manual de usuario

Eliminator Lighting

Eliminator Lighting HD-MB40 Manual de usuario

Eliminator Lighting

Eliminator Lighting MIN130 Manual de usuario

Eliminator Lighting

Eliminator Lighting Motion 60 LED Manual de usuario

Eliminator Lighting

Eliminator Lighting STRYKER BEAM Manual de usuario

Eliminator Lighting

Eliminator Lighting e 139 Manual de usuario

Eliminator Lighting

Eliminator Lighting STRYKER WASH Manual de usuario

Eliminator Lighting

Eliminator Lighting MEGA GO PAR 64E Manual de usuario

Eliminator Lighting

Eliminator Lighting EX-6 Manual de usuario

Eliminator Lighting

Eliminator Lighting EX-2 Manual de usuario

Eliminator Lighting

Eliminator Lighting IKON PROFILE PLUS Manual de usuario

Eliminator Lighting

Eliminator Lighting MEGA HEX L PAR Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario