ELEMENTICE Walker+ Manual de usuario
Contents
Compliance Statements .............................................................................................3
Mounting and Connecting Walker to your Camera ................................................5
Battery Charging and Maintenance ..........................................................................8
Powering on, powering off + rebooting a Walker .................................................10
Important Camera Settings......................................................................................11
Status Lights on Walker............................................................................................14
Pairing a Reader ........................................................................................................15
Reader Screen & Control Basics..............................................................................16
Using the Barcode/QR Code Scanner.....................................................................17
Console + remote management of device settings ..............................................18
Compliance Statements (for North American devices)
Information to the user (FCCPart 15.105)
Class B product:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
•Consult the dealer or an experienced radio/TV technician for help
Modification Warning (FCC Part15.21)
Warning: Any changes or modifications not expressively approved by MENTIS
TECHNOLOGIES (trading as ELEMENTICE) could void the user's
authority to operate this equipment.
This Device complies with Part 15 of the FCC Rules and Innovation, Science and
Economic Development Canada’s license-exempt RSS(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
CAN ICES-3 (B)/NMB-3(B)
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Mounting and Connecting Walker to your Camera
The included L-Bracket is a universal 38mm mounting bracket. Use the shorter
included D-bolt to mount the L-Bracket to your camera as pictured. The Walker
has a corresponding dovetail slot to slide onto the mount, either to the left of
the camera or underneath.
Left Side Mount (recommended for most cases)
1) Slide the Walker into position from the top so that the blue face is facing the
back of the camera and the indicator lights are visible to you while shooting.
2) Finger tighten the Position Locking Bolt (longer D-bolt) so that the Walker can’t
slide off the mount by accident.
3) Select the correct camera cable for your camera and plug the 2.5mm
headphone jack into the Walker pushing firmly, and the USB end into your
camera’s USB port.
4) Secure the L-Bracket to your camera body so that the L-Bracket’s vertical side
safely covers and protects the USB port of the Camera.
Bottom/Right side mount
Bottom/Right side mount is usually only used for shooting with the camera in
portrait orientation, on a tripod when this can't be done using a Left side mount.
We'll start by setting up with the camera sitting normally on the table, and then
you can turn it 90 degrees for portrait orientation when you attach it to the
Tripod.
1) Select the correct camera cable for your camera and plug the USB end into
your camera’s USB port.
2) Secure the L-Bracket to your camera body so that the L-Bracket’s vertical side
safely covers and protects the USB port of the camera, but there is additional
space for the Position Locking Bolt (longer D-bolt) to use the 1/4" thread at the
bottom, near the corner of the L-Bracket.
3) Slide the Walker onto the longer side of the L-Bracket from the right of
camera so that the blue face is facing the back of the camera and the indicator
lights are visible to you while shooting.
4) Finger tighten the Position Locking Bolt so that the Walker can’t slide off the
mount by accident.
5) Take the loose end of the USB cord you already plugged in, (it will be a 2.5mm
headphone jack) and plug it in to the Walker, pushing firmly.
Mounting to Tripod.
You can now mount the camera to your tripod using any compatible universal
quick release or directly using the 1/4" threads on the L-Bracket.
Bottom/Right side mount is usually only used for shooting with the camera in
portrait orientation, on a tripod when this can't be done using a Left side mount.
We'll start by setting up with the camera sitting normally on the table, and then
you can turn it 90 degrees for portrait orientation when you attach it to the
Tripod.
*If your quick release system is incompatible with the L-Bracket directly, you can
also use the 1/4" threads on the L-Bracket as mounting points for your own
quick release plates.
Battery Charging and Maintenance
The Walker does not have a display of its' own, but the connected Reader
displays the battery level of itself (R) and the Walker (W) it is paired to, in the top
right corner of it's screen.
You can also see the battery level of all online devices on the ELEMENTICE
Console, including at the Device Page.
Our devices are compatible with Fast Charging. Using a fast charger, a Walker
would charge to 50% in 30-40 minutes and 100% in around 90 minutes. Using a
standard charger approximately doubles these times.
If the device battery was completely depleted on last use or the device was left
off charge for an extended period, battery protection will have kicked in and you
will need to charge the device to 100% before it will turn on again.
To ensure the ongoing health of your device's battery, each of your ELEMENTICE
devices should be fully charged at least once every two weeks.
Powering on, powering off + rebooting a Walker
Powering On
Press and HOLD the Power button for approximately three seconds (black
button located on the blue face of your Walker... the only button on the entire
Walker), then watch the four status lights next to the power button, as it boots...
Powering Off
Press and HOLD the Power button for approximately three seconds until most
of the status lights turn off. The green Power light will stay on for a short time
while it completes power-down procedures. (If a Reader is paired, it will also
shutdown automatically after the Walker shuts down.)
Restart or shutdown from Console
With your Walker turned on, open the ELEMENTICE Console and click on
"Devices" tab on the top banner of the Console and select the relevant Walker.
You are now on the Device Page and can access the Shutdown or Restart
commands from the row of controls above the image feed.
Tabla de contenidos
