ElektraLite Cool White Dazer Manual de usuario

Elektralite LED

Cool White Dazer

USER MANUAL

Elektralite (a division of Group One),

70, Sea Lane, Farmingdale, NY11735, U.S.A.

T. +1 (631)-396-0184. F. +1 (631)-396-0190

WWW.MYELEKTRALITE.COM

1. Unpacking

Thank you for choosing the Elektralite Led Pro Line Cool White Dazer fixture. For your own safety, please read this

manual before installing the fixture. This manual covers important information on installation and applications. Please keep

this manual for future reference.

To keep this simple, we are going to refer to the fixture as the Elektralite CW Dazer throughout the manual.

The Elektralite CW Dazer fixture uses 36 high powered 5 watt leds in a balanced arrangement giving incredible output.

Please unpack it carefully and check whether it was damaged in shipping.

The following items should be in the box with the fixture:-

Color/Gel frame

DMX 5 pin male to 5 pin female cable

2. Safety Instructions.

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is

absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. The

Elektralite CW Dazer is a high voltage fixture. Be careful when dealing with high voltages.

Please read this manual. If you do not read this manual and damages occur to the Elektralite CW Dazer, then it

could void the warranty.

During shipping, Elektralite CW Dazer may have been exposed to high temperature changes or humidity changes. So, as a

precaution, do not switch Elektralite CW Dazer on immediately. Condensation can damage Elektralite CW Dazer so leave

it switched off, until it has reached room temperature.

The electric connection must be carry out by a qualified person and it is absolutely essential that the Elektralite CW Dazer

be grounded.This is imperative and is a safety issue. Do not break or bend out of the way, the ground center pin on the

plug.

Always disconnect the Elektralite CW Dazer from the power source, when the device is not in use or before cleaning it. Only

unplug Elektralite CW Dazer from the power cord. Never pull out the plug out by pulling on the power cord.

Please keep the Elektralite CW Dazer away from children and the general public. Please be intelligent and use common

sense when operating the Elektralite CW Dazer.3. General Guidelines.

The Elektralite CW Dazer is a lighting fixture for professional use on stages, in churches, theatres, etc.

The Elektralite CW Dazer should only be operated at between 120 to 240 volts and only indoors.

The Elektralite CW Dazer should not be operated 24/7 (24 hours a day; 7 days a week). The Elektralite CW Dazer needs

operation breaks to ensure that it will work for a long time without problems. Please do not shake the Elektralite CW Dazer

and avoid using brute force when installing or operating it.

When choosing the location to install the Elektralite CW Dazer, please make sure that it is not exposed to extreme heat,

moisture or dust. The minimum distance between the Elektralite CW Dazer and the illuminated surface must be more than 3

feet.

Always mount the Elektralite CW Dazer with an appropriate safety cable/chain.

Operate the Elektralite CW Dazer only when you are familiar with the features on the fixture. Do not permit operation by

persons not qualified to operate it.

All modifications to the Elektralite CW Dazer will invalidate the warranty. There are absolutely no exceptions.

If Elektralite CW Dazer is operated in any way different to the one described in this manual, the Elektralite CW Dazer

maybe damaged and the guarantee will be void.

4. Installation

Please ensure that the Elektralite CW Dazer is hung using the appropriate "C" clamp or half cheeseboro. A safety chain or

cable should also be used as a secondary point of holding the fixture in case the clamp comes loose. Never hang the

fixture without a safety chain or cable. Make sure the Gel frame (Gel holder) is clipped into position correctly and cannot

come loose.

If you are not qualified or have any doubts about hanging the Elektralite CW Dazer then do NOT hang it.

Do not clamp the cable to the U bracket or clamp. That is not a secondary safety point.

A secondary safety point is any point that will adequately hold the Elektralite CW Dazer if the "C" clamp or half cheesboro

fails. Then the safety cable would be the backup and stop the fixture from falling to the ground. So do NOT fix the safety to

the same place that the "C"clamp is attached.

Installation during construction.

Many times fixtures are installed during the construction phase of a building. It is imperative that the fixture is protected

during this phase. A lot of dust is usually created. This dust can adversely affect the fixture. Specifically, of course, in coating

the lenses and therefore reducing the output. However much more seriously, dust, like sheetrock dust, can get inside the fan

bearings especially if the fixture is being operated during construction. Sheetrock dust, mixed with the grease of the fan

motor, will result in the fan’s premature failure and that is not covered under the fixture’s warranty. It is therefore strongly

advised to keep the fixtures covered up during the construction phase and not used.

5. Grounding.

Always make sure that there is sufficient grounding (earth) for the fixture. This is not only imperative within the circuit that the

fixture is being connected to, but also make sure there is sufficient grounding into the building. All fixtures regardless of

manufacturer have a surge at initial “turn-on”. Once initial “turn-on” is complete, the surge current (per fixture) will travel

down the ground. While each 20 Amp circuit may have the correct size of ground wire, the ground input to the building

and/or electrical panel may not be sufficient for the job. Please review this with the electrical contractor. The Elektralite CW

Dazer has a surge current over and above its operating current of approximately 2 Amp at 120 volts. If an installation has

100 Dazers that means 200 Amps needs to be dissipated through the GROUND WIRING. If there is a lack of a sufficiently

big enough ground cable into the building or on the individual circuits it can cause severe damage to the fixture and this is

not covered under the warranty.

One further check : the ground to neutral voltage for each circuit. In a lot of buildings, voltages across these can damage

fixtures or cause operational problems both for the fixture and DMX.

Please review these two important points with a qualified electrical contractor. If in any doubt, have an independent qualified

third party electrical contractor check the installation, well before commencing installation.

Circuit Limitation :-

There should be no more than 5 CW Dazers on a 20 amp 120 volt circuit, having no other load on it. That means to say a,

maximum of 5 CW Dazers are on a 20 amp 120 volt circuit with nothing else plugged into that circuit.

6. DMX-512 Control Connection

Connect the provided XLR cable to the female 5-pin XLR output of the Elektralite CP 16/24 or other DMX controller. The

other end should be connected to the male 5-pin XLR input of the Elektralite CW Dazer . Then daisy-chain out of the first

Elektralite CW Dazer and into the next Elektralite CW Dazer or other dmx device. Never “Y” split the DMX connection.

If you need more cable, then it should be two core, screened cable fitted with a 5 pin XLR input and output connector. Please

refer to the diagram below.

DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically “noisy” environment, it is

recommended that a DMX terminator is used. This helps prevent corruption of the digital control signal. The DMX terminator

is simply a 5 pin XLR plug (male) with a 120 Ωresistor connected between pins 2 and 3. It is then plugged into the output

XLR socket of the last Elektralite CW Dazer or other dmx device in the chain. Please see illustration below.

120

7. Menus in the fixture.

Root Menu Sub Menu 1 Sub Menu 2

STAT (STATIC LOOK) W(HITE) 0-255

S(STROBE) 0-255

RUN DMX

STMT

DMX ASSIGN DMX CHANNEL 1-512

PERS (PERSONALITY) WD

WS Id

ID ID 01 THROUGH 255 1-255

SET REST (RESET)

DIM

KEY OFF

8. Static Look.

The Elektralite CW Dazer can be set to a single static look quickly.

Use the Menu button to get to STAT.

Press Enter.

The next screen will read W.000. This is addressing the White leds.

Use the ↑or ↓to increase or decrease the output of the leds.

Numbers are expressed in DMX values so 0 is no output and 255 is highest output.

Press Enter to save the value.

The screen will automatically advance to the strobe. S.000 means the strobe is off

Use the ↑or↓to increase or decrease the speed of the strobing or leave at S.000 if you want no strobe.

S.001 is the slowest and S.020 is the fastest strobing.

Press Enter to save the value. It will automatically bring you back to the output screen again.

Press the Menu button to exit out of STAT and back to the Root directory.

9. Run Mode.

Run allows the fixture to operate in either DMX or STMT.

DMX Mode is where control of the fixture is via the industry standard DMX signal.

Further, when the DMX signal is lost, the fixture will maintain the last refresh of the DMX signal prior.

This way the facility is not plunged into total darkness.

In STMT Mode, when the DMX signal is lost, the fixture will go to whatever the output values are set at in the STATIC LOOK.

STMT mode is good in an emergency.

If the fixtures are in a venue that needs, in an emergency, the lights to come FULL ON, then engage STMT mode and also

make sure that the STATIC LOOK is set such that all leds are at 255. (See #8 Static Look above).

Using the Menu button in the root menu go to RUN.

Press Enter to get to DMX mode. Press Enter again to save the RUN mode as DMX.

A "ok" will appear and then the display will return to display RUN.

If the fixture is to be run in STMT mode, then when DMX mode appears on the screen instead of pressing enter use the ↑or ↓

to get to STMT. Then press enter to save the STMT mode setting.

10. DMX 512 Setting (address).

Sets up the address for the dmx.

Using the Menu button in the root menu go to DMX

Press Enter to get into DMX menu and the display will read the current dmx channel.

The display will read for example d.001

This means the fixture's current address is 001

To change it, use the ↑or ↓buttons to get to the correct address.

Press Enter to save the dmx address. The display will momentarily display the word "OK" and then go back to the DMX menu.

To exit out to the root directory, use the menu button.

11. Fixture Personality.

There are several different choices on how the fixture will operate.

What these "Personalities" do in terms of their channel assignments is detailed on the tables page 8.

To change a Personality use the Menu button to get to PERS

Press Enter and then using the ↑or ↓buttons go to the personality required.

Press Enter to save the Personality.

12. ID Address.

A fixture can be addressed (controlled) through the dmx or instead it can have its own unique ID address.

There are a total of 255 different ID addresses from 1 to 255.

To set up the address for a fixture, use the Menu button in the root menu go to ID

Press Enter and then using the ↑or ↓buttons,to select the ID address.

Press Enter to save the address.

For the ID address to work you must chose the WS id personality.

This allows you to access the ID address system on channel 4.

Set the DMX address to d.001 for the fixture. So if ID address 123 is chosen then go to channel 4 on the lighting board and

set the level at 123. You will then be controlling only fixture(s) with ID address 123.

13. SET. (Set has several Sub Menus which allow functions to be used).

1). REST

This resets all values to their default.

Using the Menu button, go through the Root Menu until SET. Press Enter and then use the ↑or ↓buttons to get to REST.

Press Enter. The display will have 4 dots across the bottom. The password needs to be entered. The password is the following

sequence using the ↑and ↓buttons.

↑↓↑↓then press Enter once, to complete the reset. The display will read "OK" followed by a return to the REST sub

menu. The Menu button will need pressing to return to the Root Menu. Only when at the Root Menu will dmx control work.

Please note the Reset also takes the dmx address back to 001.

2). DIM

The Dim function allows different Dimmer curves to be chosen. There are 5 choices.

Choice 1 :- this is Dim off. The Dimmer curve is 0 which means any change in dimmer level is instantaneous.

Choice 2:- Dim 1. The dimmer curve has the shortest fade in and fade out time.

Choice 3:- Dim 2. The dimmer curve has the 2nd shortest fade in and fade out time.

Choice 4:- Dim 3. The dimmer curve has the 3rd shortest fade in and fade out time

Choice 5:- Dim 4. The dimmer curve has the longest fade in and the fade out time.

Using the Menu button, go through the Root Menu until Set. Press Enter and then use the ↑or ↓buttons to get to DIM.

Press Enter and then use the ↑or ↓buttons to get to the DIM choice required. Once chosen, press Enter to save it and then

use the Menu button to exit back to the root directory.

3).DV

The DV setting allows the ability of the leds to not flicker when using video camera.

The choices are NTSC or PAL. NTSC is the USA system.

Go through the Root Menu until Set. Press Enter and then use the ↑or ↓buttons to get to DV.

Press Enter and then use the ↑or↓buttons to get to either NTSC or PAL. Once chosen, press Enter to save the setting and

the Menu to exit back to the Root Menu.

14. KEY

The Key function is an access password for the fixture. The KEY can be turned OFF or ON which then deactivates or activates

the password.

To set the KEY go through the Root Menu until KEY, press Enter and use the ↑or ↓to set the KEY to either OFF or ON. If the

Key is turned ON then a password is required to go into sensitive Menus and to change functions.

The password is ↑↓↑↓(Up + Down + Up + Down)

15. Glass front plate.

Certain fixtures come with a glass plate. This glass plate fits onto the front of the leds. It slots in the gel frame holder and the

clip latches the plate into position.

16. The Personalities of the CW Dazer.

1 0-255 Dimmer

0-50 Linear dimmer speed（DIM=OFF）

51-100 nonlinear speed1（DIM1）

101-150 nonlinear speed 2（DIM2）

151-200 nonlinear speed 3（DIM3）

201-255 nonlinear speed 4（DIM4）

1 0-255 Dimmer

0-9 No Function

10-49 Synchronized strobe slow

50-99 Non synchronized strobe slow

100-149 Random strobe slow

150-199 Non synchronized fast strobe

200-255 Synchronized fast strobe

0-50 Linear dimmer speed（DIM=OFF）

51-100 nonlinear speed 1（DIM1）

101-150 nonlinear speed 2（DIM2）

151-200 nonlinear speed 3（DIM3）

201-255 nonlinear speed 4（DIM4）



WS Id

1 0-255 Dimmer

0-9 No Function

10-49 Synchronized strobe slow

50-99 Non Synchronized strobe slow

100-149 Random strobe slow

150-199 Non Synchronized strobe fast

200-255 Synchronized strobe fast

0-50 Linear dimmer speed（DIM=OFF）

51-100 nonlinear speed 1（DIM1）

101-150 nonlinear speed 2（DIM2）

151-200 nonlinear speed 3（DIM3）

201-255 nonlinear speed 4（DIM4）

0 All ID address work together

1-255 Each dmx value is an ID address value.

Each ID address is controlled individually at that DMX value

17. DMX Channel Assignments.

Depending on the Personality chosen, the Elektralite CW Dazer can be 2, 3 or 4 channels.

Personalities:-

WD = 2 channels (the first two channels listed below)

WS = 3 channels (the first three channels listed below). WS is the most common choice.

WS Id = 4 channels (as listed below all 4 channels)

1 0-255 Dimmer

0-9 No Function

10-49 Synchronized strobe slow

50-99 Non Synchronized strobe slow

100-149 Random strobe slow

150-199 Non Synchronized strobe fast

200-255 Synchronized strobe fast

0-50 Linear dimmer speed（DIM=OFF）

51-100 nonlinear speed 1（DIM1）

101-150 nonlinear speed 2（DIM2）

151-200 nonlinear speed 3（DIM3）

201-255 nonlinear speed 4（DIM4）

0 All ID address work together

1-255 Each dmx value is an ID address value.

Each ID address is controlled individually at that DMX value

Tabla de contenidos

Otros manuales de Equipo de DJ de elektraLite

elektraLite

elektraLite Stingray Manual de usuario

elektraLite

elektraLite eyeBall (5-in-1) Manual de usuario

elektraLite

elektraLite 1018 Manual de usuario

elektraLite

elektraLite eyeBall IP65 Manual de usuario

elektraLite

elektraLite Dazer Downlight Warm White Manual de usuario

elektraLite

elektraLite LXE 700 Spot Manual de usuario

elektraLite

elektraLite CP10XT Manual del operador

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario

elektraLite Cool White Dazer Manual de usuario

Manuales populares de Equipo de DJ de otras marcas