Elegoo MARS MATE Manual de usuario
MARS MATE
Air Purifier
User Manual
Thank you for purchasing ELEGOO brand products.
After receiving the product, please confirm whether the equipment is intact and the accessories
are complete. If there is any damage or missing, please timely contact us at 3dp@elegoo.com. (To
ensure the performance of each product, each product will undergo strict testing before leaving the
factory. There may be some slight scratches when you receive the product, which is normal, please
rest assured to use.)
Notice:
Do not block the air inlet/outlet.
Do not rinse the composite filter with water.
Do not unplug/plug the power plug when your hands are wet.
Regularly remove the dust on the air purifier and power plug.
Only the supplied power adapter and matched special filter element can be used.
Do not use the air purifier in places with heavy humidity or oily fumes, such as bathrooms.
Please be careful when cleaning the air purifier, strong corrosive cleaning agents can damage the
air purifier's surface.
When using the air purifier, do not place it near or on objects with a heat source (such as a fireplace,
heater, or a place where it may be exposed to flammable gases).
Unplug the power cord from the electrical outlet when cleaning the air purifier or not in use.
Otherwise, it may result in electric shock due to poor insulation or fire due to a short circuit.
This air purifier is not suitable for operation by the disabled, sensory impaired, mentally impaired,
or children. Exceptions are made if a person liable for safety is present to supervise and provide
guidance to assist in the operation of this machine.
Packing List
MARS MATE Air Purifier
User Manual
Composite Filter
(already installed in the machine)
Nuts (4 pcs)
Screws (4 pcs) Allen wrench
Adapter
Connector Seat Connector Hose
Open end wrench
Machine Parameters
Machine Name：MARS MATE Air Purifier
Machine Model：AP01
Rated Voltage：100-240V 50/60Hz
Rated Power：12V 0.5A
Noise：35dB
Net Weight：5.2kg
Gross Weight：7.0kg
Product Size：210x247x410mm
Package Size：479x281x324mm
Working Environment：Temperature：14 F-104 F (-10°C-40°C); Humidity: ≤95%RH
Machine Introduction
Air Outlet
1Touch Control Button
2Host
3Composite Filter
5
Open Lid Button
4
PUSH PUSH
Operating Instructions
On/Off Button
Short press the "on/off button" to turn on the machine, and long press the "on/off button" for 3
seconds to turn off the machine; the icon for the power on status will light up in white, and the
icon for power off state will light up in red.
Fan Speed Button
Short press the "fan speed button" to turn on the low fan speed, and the fan speed icon will change
from semi-bright to full bright, and the first indicator light on the left will light up (transparent white
light). Short press the "fan speed button" again to switch to the high fan speed, and the two indicator
lights will light up at the same time; Short press to switch between high and low fan speed.
Auto Button
Short press the "auto button" to enter the automatic mode, and the auto icon will change from
semi-bright to full bright. With 1 hour as the unit, the fan speed switch between high and low gear;
run at high speed (10 minutes), and run at low speed (50 minutes); the high and low speeds are
cycled by duration.
Filter Reset Button
1. When the sensor detects VOC concentration ≥ 1.4PPM, the air quality light is red, and the red
light of the filter icon flashes, prompting the user to replace the filter element. Long press the
"filter reset button" for 3 seconds to reset the filter, and the red light of the filter button icon stops
flashing and goes out. The life time of the filter is greater than 1440 hours, or the VOC concentration
is greater than 1.4PPM, whichever is the priority will be the filter replacement alarm standard.
＜0.7PPM
0.7PPM-1.4PPM
≥1.4PPM
green
yellow
red
excellent
moderate
poor
AQI air quality indicator lightAir qualityVOC concentration value
AQI Air Quality Indicator Light Description
Operating Instructions
2. Forced reset the filter life, within the 30s of power-on, in standby mode, long touch the "auto
button" for 3 seconds + short touch the "filter reset button" for 3 times to enter the filter life
reset, and after sending a "ding" sound, the red indicator light of the filter flashes about 5 times,
frequency: 0.5 seconds/time, indicating that the forced reset action is completed. When the machine
is powered on again after power off, the white light of the filter indicator light will be half lit.
Start using
1. Take out the connector hose and connect it to the extension port of the 3D printer.(Screws and
wrenches are in the accessories package)(See Picture 1)
2. Remove the connector hose and connect it to the air purifier and the 3D printer. (See Picture 2)
(Picture3） (Picture4）
(Picture1） (Picture2）
Instructions for Use
3. Plug in the adapter to power on the machine, and the buzzer will make a "ding" sound.
(See Picture 3)
4. Touch the power switch button to turn on the machine. (See Picture 4)
3Take out the filter in the machine.
2Lift up the upper part of the machine.
1Press the button lightly with your
hand according to the labeled
button on the product.
PUSH
PUSH
PUSH
Filter Replacement
Note: Before use, please ensure that the plastic protective bag outside the filter cartridge is
removed and installed correctly.
4Remove the plastic protective bag
from the filter. 5Reinstall the filter into the machine
with the protective bag removed.
6Reinstall the upper part of the
machine.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
