Electrolux EWF12844 Manual de usuario
28
www.electrolux.com
INSTALLATION11.
11.1 Unpacking
You are advised to keep all transit
devices so that they can be
refitted if the machine ever has to
be transported again.
Cut and remove four cut out
straps as shown.
All transit bolts and packing
must be removed before using
the appliance.
CAUTION!
1.
ENGLISH 29
Remove the carton box and plastic
bag which cover the machineas as
indicated on picture.
Open the door. Remove all the items
from the drum.
2.
3.
4.
5.
6. Remove the polystyrene base.
Put one of the polystyrene packaging
elements on the floor behind the
appliance. Carefully put down the
appliance with the rear side on it.
Make sure not to damage the hoses.
Open top flaps and remove internal
foam inserts as shown on picture.
30
www.electrolux.com
7. Pull up the appliance in vertical
position.
8.
9.
10. Pull out the plastic spacers.
Remove the power supply cable and
the drain and inlet hoses from the
hose holders (A) on the rear of the
appliance.
Remove the three bolts.
A
11. Put the plastic caps in the holes.
You can find these caps in the user
manual bag.
1
2
3
Use a spirit level on the top and
side of the washing machine to
check the levels.
It is important that your
washing machine stands firm
and level on the floor to ensure
correct operation.
11.2 Positioning The appliance must not be installed
behind a lockable door, a sliding
door or a door with a hinge on the
opposite side so that the washing
machine door is restricted.
IMPORTANT
ENGLISH 31
Never place cardboard, wood or
similar materials under the machine
to compensate for any unevenness
in the floor.
When the washing machine is
levelled, try to rock it from corner
to corner. If it does rock, adjust the
legs again until it is levelled and
does not rock.
Connect the water inlet hose to a
tap with 3/4” BSP thread.
Use the hose supplied with the
washing machine. DO NOT USE
OLD HOSES.
The other end of the inlet hose
which connects to the machine
can be turned in any direction.
Simply loosen the fitting, rotate the
hose and retighten the fitting,
making sure there are no water
leaks.
11.3 Water Inlet
Install the machine on a flat hard
floor. Make sure that air circulation
around the machine is not
impeded by carpets, rugs etc.
Check that the machine does not
touch the wall or cupboard units.
Loosen or tighten the feet to adjust
the level. A correct adjustment of
the appliance level prevents the
vibration, noise and the movement
of the appliance when in operation.
If you do not have a spirit level, as a
guide use the edge of a door frame,
cupboard or bench to check that
the washing machine is level.
32
www.electrolux.com
The inlet hose must not be
lengthened. If it is too short and
you do not wish to move the tap,
you will have to purchase a new,
longer hose specially designed for
this type of use.
This could be done by tying it to
the tap with a piece of string or
attaching it to the wall.
In a sink drain pipe branch. This
branch must be above the trap
so that the bend is at least 60 cm
above the ground.
Directly into a drain pipe at a
height of no less than 60 cm
and no more than 90 cm. The
end of the drain hose must
always be ventilated, i.e. the
inside diameter of the drain pipe
must be larger than the outside
diameter of the drain hose.
The drain hose must not be
kinked. Run it along the floor, only
the part near the drainage point
must be raised.
The end of the drain hose can be
positioned in three ways:
Hooked over the edge of a sink
using the plastic hose guide
supplied with the machine.
For correct functioning of the
machine the drain hose must
remain hooked on the proper
support piece situated on the top
part of back side of the appliance.
In this case, make sure the end
cannot come unhooked when
the machine is emptying.
11.4 Water Drainage
Please check rated power
supply condition that is
mentioned on the Rating
Label before you connect
to the power supply.
“An incorrect power
supply may void your
warranty.”
Check that your domestic electrical
installation can take the maximum
load required (2.0 kW), also taking
into account any other appliances
in use.
If the supply cord is
damaged, should the
appliance power supply
cable need to be replaced,
this shall be carried out by
our Service Centre.
The manufacturer declines any
responsibility for damage or injury
through failure to comply with the
above safety precaution.
This machine is designed to
operate on a 220-240 V, single-
phase, 50 Hz supply.
11.5 Electrical Connection
Connect the machine to
an earthed socket outlet.
ENGLISH 33
When the appliance is installed
the power supply cable must be
easily accessible.
If this appliance is supplied from a
cord extension set or electrical
portable outlet device, the cord
extension set or electrical portable
device must be positioned so that
it is not subject to splashing or
ingress of moisture.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Arandela de Electrolux
Electrolux
Electrolux EW6S307SI Manual de usuario
Electrolux
Electrolux EWF 1404BR Manual de usuario
Electrolux
Electrolux EWF 12821 Manual de usuario
Electrolux
Electrolux Swissline GL EWF 1387 Manual de operación
Electrolux
Electrolux WAL4E201 Manual de usuario
Electrolux
Electrolux EWF 605 Manual de usuario
Electrolux
Electrolux EW6S426W Manual de usuario
Electrolux
Electrolux EWI1235 Manual de usuario
Electrolux
Electrolux EWS 126540 W Manual de usuario
Electrolux
Electrolux WA SL3 E 101 Manual de usuario
Electrolux
Electrolux EW 1100 F Guía rápida
Electrolux
Electrolux CALIMA EWFM 12470 W Manual de usuario
Electrolux
Electrolux EW 1232 F Manual de usuario
Electrolux
Electrolux EWF14023S Manual de usuario
Electrolux
Electrolux EWT 2066EEW Manual de usuario
Electrolux
Electrolux EWFLS70J IW Manual de usuario
Electrolux
Electrolux W455H Manual de usuario
Electrolux
Electrolux U28190 Manual de usuario
Electrolux
Electrolux EWB 76210 W Manual de usuario
Electrolux
Electrolux EWS 7146 EDU Manual de usuario
