Electrolux EIDW6405HT - Fully Integrated Dishwasher Manual de usuario

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

SERVICE MANUAL

CONTENTS:

This document contains the instruction to change parameter settings of electronic

board by means of user interface.

EDITION: 06.2005

TANK

BOILER

3.__

TANK

BOILER

3.__

TANK

BOILER

3.__

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

INDEX

1. KEYBOARDS 3

1.1 HOODTYPE Style 3

1.2 UNDERCOUNTER Style 4

2. MANUAL ACTIVATION OF DETERGENT AND RINSE AID DISPENSERS 5

2.1 Detergent Dispenser Activation 5

2.2 Rinse Aid Dispenser Activation 5

3. RINSE PUMP MANUAL ACTIVATION 5

4. DETERGENT AND RINSE AID DOSAGE 6

GEn General Parameters 6

5. COUNTERS 8

Cnt Counters 8

6. TEMPERATURE SETTING 9

FAC Factory Parameters 8

7. CYCLE SETTING 11

CYCLE DIAGRAM

CY1 Cycle 1 Parameters 13

CY2 Cycle 2 Parameters 13

CY3 Cycle 3 Parameters 13

drn Drain/Cleaning Cycle Parameters 13

8. OTHER PARAMETERS 14

dPA Dishwashing Parameters 14

ron Read Only Parameters 14

HCP Communication and HACCP Parameters 14

CFG Configuration Parameters 15

dbG Parameters for automatic hood type dishwashers 16

9. SPECIAL FEATURES 17

9.1 RESIN REGENERATION CYCLE 17

9.2 MEDICAL LINE DISHWASHER WITH DOOR/HOOD LOCK DEVICE 17

9.3 DETERGENT AND RINSE AID LEVEL SENSORS ACTIVATION 17

9.4 dISHWASHER WITH INCORPORATED CONTINUOUS WATER SOFTENER 18

10. MAIN BOARD CONFIGURATION 19

10.1 CODEÆProg. TABLE 19

10.2 PROGRAMMING SHEETS 24

11. DEFAULT VALUES 72

12. USER INTERFACE AND MAIN BOARD CONNECTORS 75

12.1 MAIN MALFUNCTIONS NOT DUE TO THE MAIN BOARD 75

12.2 CONNECTORS LAYOUT 75

13. ALARM MESSAGES AND TROUBLESHOOTING 82

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

1. KEYBOARDS

1.1. HOOD TYPE Style

SETTING MODES:

To enter into one setting mode (Fig.1.4, Fig.1.5) the appliance should be in stand-by: switch on the

appliance, no cycles selected. Is useful keep door open to avoid start cycle in case of not

simultaneously pressure of the two keys.



Fig. 1.5

Enter into Factory Parameters

(Hold down buttons for at least

five seconds).

FAC



Fig. 1.8

Confirm Value and go

to next Parameter

(In setting mode only)

888



Fig. 1.7

Decrease Parameter Value

(In setting mode only)

888



Fig. 1.6

Next Parameter Family OR

Increase Parameter Value

(In setting mode only)

888



Fig. 1.2

Rinse Aid Dispenser

Manual Activation.

rAi



Fig. 1.3

Rinse Pump

Manual Activation

(used to EMPTY BOILER)

---



Fig. 1.4

Enter into General Parameters

(Hold down buttons for at least

five seconds).

GEn



Fig. 1.1

Detergent dispenser

Manual Activation.

dEt



dEt



rAi



---



GEn



FAC



888



888



888

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

1.2. UNDERCOUNTER Style

SETTING MODES:

To enter into one setting mode (Fig.1.4, Fig.1.5) the appliance should be in stand-by: switch on the

appliance, no cycles selected. Is useful keep door open to avoid start cycle in case of not

simultaneously pressure of the two keys.



TAN

BOILER

dEt

Fig.1.1

Detergent dispenser

Manual Activation



TAN

BOILER

rAi

Fig.1.2

Rinse Aid Dispenser

Manual Activation



TAN

BOILER

---

Fig.1.3

Rinse Pump

Manual Activation

(used to EMPTY BOILER)



TAN

BOILER

GEn

Fig. 1.4

Enter into General Parameters

(Hold down buttons for at least five

seconds).



TAN

BOILER

FAC

Fig. 1.5

Enter into Factory Parameters

(Hold down buttons for at least five

seconds).



TAN

BOILER

888

Fig.1.6

Next Parameter Family

Increase Parameter Value

(in setting mode only)



TAN

BOILER

888

Fig.1.7

Decrease Parameter Value

(In setting mode only)



TAN

BOILER

888

Fig.1.8

Confirm Value and go to next Parameter

(in setting mode only)

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

2. MANUAL ACTIVATION OF DETERGENT AND RINSE AID

DISPENSERS

When replacing detergents may be necessary activate the dispensers to fill hoses.

2.1. Detergent Dispenser Activation

Switch on the dishwasher.

Press and hold down CYCLE_2 and CYCLE INFINITE keys, after two 'beep' the detergent dispenser

starts work for 20 sec.

2.2. Rinse Aid Dispenser Activation

Switch on the dishwasher.

Press and hold down CYCLE_1 and CYCLE INFINITE keys, after two 'beep' the rinse aid dispenser

starts work for 40 sec.

3. RINSE PUMP MANUALACTIVATION

Use this function to empty the boiler (if the dishwasher is not to be used for a long time, for maintenance operation: ex. before replacing

main board).

Switch on the dishwasher.

Close the door and press and hold down DRAIN and CYCLE INFINITE keys. A buzzer signal indicates the

rinse pump activation and the display shows three blinking lines. Three beeps indicate the cycle end.



dEt



rAi



---

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

4. DETERGENTAND RINSE AID DOSAGE

In this paragraph is explained how to set the working time for the detergent and rinse aid dispensers.

For each dispenser there are two parameters: the initial time and the time during cycle execution.

GEn General Parameters

Sym. Parameter Description Unit Min Max Factory

Default

dIn Initial Detergent Dosage (during filling tank) [s] 0 240 90

rIn Initial Rinse Aid Dosage (starts when tank filled) [s] 0 180 10

dEt Detergent Dosage During Cycle Execution (during wash phase) [s] 0 182(*) 8

rAi Rinse Aid Dosage During Cycle Execution (when refilling boiler) [s] 0 62 (*) 4

How change the duration:

•Switch OFF and switch ON the dishwasher;

•Enter into the USER SETTING mode by pressing and hold down ON/OFF and CYCLE_1 keys for at least five seconds the display

shows GEn (Fig.3.1);

•Press CYCLE_INFINITE. The display shows alternatively the symbol dIn and the duration in seconds (Fig.3.2 and 3.3);

NOTE: If User Interface v.3.00 tank led is on if value correspond to factory default (Default 1, HOOD TYPE).

•Use CYCLE_1 key to decrease the duration and CYCLE_2 key to increase (Fig.3.3);

•After settled the duration press CYCLE_INFINITE key to store value. The display shows the next parameter (Fig.3.4) and the

corresponding value (Fig.3.5);

•In the same way is possible to change the other duration; when finished switch OFF and switch ON.

Fig. 3.8

Cycle rinse aid dosage

rAi

©ª



Fig. 3.9

Change time activation

©ª



DEFAULT

Fig. 3.7

Change time activation

(Tank LED indicates default)

Fig. 3.6

Cycle detergent dosage

dEt

Fig. 3.2

Initial detergent dosage

dIn

©ª



DEFAULT

Fig. 3.3

Change duration.

(Tank LED indicates default).

Fig. 3.4

Initial rinse aid dosage

rIn

©ª



Fig. 3.5

Change duration





Fig. 3.1

Enter into User Mode

(press for 5 sec).

GEn

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

(*) Note for external dispensers:

•If DEt=181 the detergent dispenser works when WASHING PUMP is being activated; at the same time voltage

is supplied between connectors L17–L19(main terminal box);

•If dEt=182 the detergent dispenser works when LOADING EV is being activated to re-fill boiler level; at the

same time voltage is supplied between connectors L17–L19(main terminal box);

•If rAi= 61 the rinse aid dispenser works when LOADING EV is being activated to re-fill boiler level; at the same

time voltage is supplied between connectors L18–L19(main terminal box);

•If rAi= 62 the rinse aid dispenser works when WASHING PUMP is being activated; at the same time voltage is

supplied between connectors L18–L19(main terminal box);

- For electrical connections refer to electric diagram -

Example

Suppose there is connected an external detergent dispenser with a probe into the tank. A typical setting could be:

DIn= 0 the dispenser is not activated during filling tank;

DEt=181 the dispenser is supplied during washing phase and the probe automatically dose the right detergent

amount.

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

5. COUNTERS

This Parameter Family collects cycle counters and water consumption counters.

For water consumption counters a flow meter must be installed. See PPL (calibration parameter) into dPA section (§ Other Parameters).

Cnt Counters

Sym. Parameter Description Unit Min Max Factory

Default

CYC Cycles performed counter.

CYC symbol and two numbers blink consecutively. The cycle number is

obtained by joining the two numbers. Ex. CYC → 10 →042 means

10042 cycles executed.

cYc Cycle counter (resettable).

This counter is similar to CYC but is resettable by user (see rSt parameter

below). -

nnc Water Consumption. [present up to software version 3.12]

Counts m3of water consumption. [m3]

L Water Consumption. [present up to software version 3.12]

Counts litres of water consumption.

The total consumption is given by adding nnc [m3] and L[l] values. [l]

Lit Water Consumption: resettable counter. [present up to software version 3.12]

Counts the litres of water and is resettable by user (see rSt parameter below). [l]

rSt Reset resettable counters: cYc and Lit

To reset put 1 this parameter, switch off and then on again: cYc and Lit

will show zero. Note that cYc is used to count cycles for CAll message

(see next parameter, nCY).

nCY Store thousand of cycles after that CAll message appears on display.

Ex. If this parameter is settled to 20, CAll message appears when cYc

reach 20.000 cycles. -

drn Drain/Cleaning cycles performed.

Similar to CYC but counts Cleaning Cycles. -

rCY Numbers of cycles that can be made after a regeneration cycle (only for

dishwashers with non-continuous water softener) [See paragraph 9.1 resin

regeneration cycle.]. - 20

NRE Regeneration cycle counter (only for water softener dishwasher)

[See paragraph 9.1 resin regeneration cycle / paragraph 9.4 Dishwashers with

incorporated continuous water softener]. -



Fig.4.2

Next Family

GEn



Fig. 4.3

Counters Fam.: ENTER

Cnt

Fig. 4.4

CYCLES

CYC



Fig.4.1

USER setting mode

(press for 5s)

GEn

Fig. 4.5

Thousand.

010



Fig. 4.6

Units.

042



Fig. 4.7

Next counter.

cYc

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

6. TEMPERATURE SETTING

In this paragraph is explained how to change temperature thresholds and all parameters related to boiler and tank.

FAC Factory Parameters

Sym. Parameter Description Unit Min Max

Factory

Default

bt°C Boiler Temperature: THRESHOLD.

When boiler temperature reaches this value, heaters switch off. [°C] 45 95 78

btH Boiler Temperature HISTERESIS, (represent dead band).

Heater switch on if boiler temperature is below: bt°C -btH [°C] 2 10 2

bHi Boiler Temperature: HIGH LIMIT.

When boiler temperature reaches this value C 2 alarm appears.

Put 0 to disable C 2 alarm. [°C] 0 98 96

bLo Boiler Temperature: LOW LIMIT.

During boiler warm-up, temperature must increase at least bLo °C otherwise

E 3 warning appears.

Put 0 to disable E 3 warning.

[°C] 0 10 1

bFL Boiler Filling Timeout.

If filling time is longer than bFL, A 1 alarm appears.

Put 0 to disable A 1 alarm. [min] 0 42 5

bAJ Boiler Temperature Adjust. [°C] 0 7 4

bP Boiler Priority (enable boiler wait function)

0=disabled

1=enabled

- 0 1 1

bSt Booster Function

Overheat gap over Boiler Temperature Threshold [°C] 0 15 2

btd Boiler temperature negative differential: when the dishwasher is in standby,

boiler threshold becomes: bt°C -btd

(Used to save energy during machine inactivity by keeping boiler water at a

lower temperature).

[°C] 0 20 0

tt°C Tub Temperature: THRESHOLD

When tank temperature reaches this value, heater switch off. [°C] 40 85 63

ttH Tub Temperature: HISTERESIS, (represent dead band).

Heater switch on if tank temperature is below: tt°C -ttH [°C] 2 30 5

tHi Tank Temperature: HIGH LIMIT.

When tank temperature reaches this value C 3 alarm appears.

Put 0 to disable C 3 alarm. [°C] 0 95 75

tLo Tank Temperature: LOW LIMIT.

During tank warm-up, temperature must increase at least bLo °C otherwise

E 2 warning appears.

Put 0 to disable E 2 warning.

[°C] 0 10 1

tFL Tank Filling Timeout.

If filling time is longer than tFL, A 1 alarm appears.

Put 0 to disable A 1 alarm. [min] 0 42 20

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

To modify thresholds do the following:

•Switch OFF and switch ON the dishwasher;

•Enter into the FACTORY SETTING mode by pressing and hold down ON/OFF and CYCLE_2 keys for at least five seconds (Fig.5.1);

•Press CYCLE INFINITE. The display shows alternatively the symbol bt°C (Fig.5.2) and the corresponding value 76 (Fig.5.3);

•Use CYCLE_1 key to decrease the value and CYCLE_2 key to increase (Fig.4.3);

•Press CYCLE INFITE key to confirm. The display shows the next parameter (Fig.4.4) and the corresponding value (Fig.4.5);

•In the same way is possible to change the other parameters; when finished switch OFF and switch ON.

At the end the display will show again ‘FAC’ and by pressing CYCLE_2 key (Fig.4.9) is possible to change cycle duration (see next

paragraph).



Fig. 5.9

Factory setting mode

FAC



Fig. 5.10

Next Family

FAC



Fig. 5.11

Cycle 1 Family: ENTER

CY1

©ª



Fig. 5.7

Change value & Store

bLo

Fig. 5.6

Tank temp. High limit.

bHi

©ª



Fig. 5.5

Change value & Store





Fig. 5.1

Factory setting mode

FAC

Fig. 5.2

Boiler temp. threshold

bt°C

©ª



Fig. 5.3

Change value & Store

Fig. 5.4

Boiler Temp Hysteresis

btH

Otros manuales para EIDW6405HT - Fully Integrated Dishwasher

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lavavajillas de Electrolux

Electrolux

Electrolux ESL 66020 Manual de usuario

Electrolux

Electrolux ESF6800ROX Manual de usuario

Electrolux

Electrolux ESLP 8815RA Manual de usuario

Electrolux

Electrolux Favorit 99000 Manual de usuario

Electrolux

Electrolux EUC1WS Manual de usuario

Electrolux

Electrolux MDB125RHD3 Manual de usuario

Electrolux

Electrolux ESI5211LOX Manual de usuario

Electrolux

Electrolux ESI5201LOX Manual de usuario

Electrolux

Electrolux FAVORIT 88080 i Manual de usuario

Electrolux

Electrolux 402070 Manual de usuario

Electrolux

Electrolux EUC1G 400063 Manual de instrucciones

Electrolux

Electrolux 534094 Manual de usuario

Electrolux

Electrolux ZANUSSI DE 6955 Manual de usuario

Electrolux

Electrolux ASF45090 Manual de usuario

Electrolux

Electrolux ESF 68070 Manual de usuario

Electrolux

Electrolux ESL5350LO Manual de usuario

Electrolux

Electrolux EDW 1003 Manual de usuario

Electrolux

Electrolux ESC67300SX Manual de usuario

Electrolux

Electrolux EPPWELGM5 Manual de usuario

Electrolux

Electrolux FAVORIT 65411 VI Manual de usuario

Electrolux

Electrolux ESI8730RAX Manual de usuario

Electrolux

Electrolux DIVA Manual de usuario

Electrolux

Electrolux ESL8350RO Manual de usuario

Electrolux

Electrolux ES I46010 Manual de usuario

Manuales populares de Lavavajillas de otras marcas

KitchenAid

KitchenAid KUDB230B Manual de usuario

Brandt

Brandt BDJ424DB Manual de usuario

Asko

Asko DSD767UXXL.AU Manual de usuario

Beko

Beko DFN26210W Manual de usuario

NEFF

NEFF S153ITX00E Hoja de especificaciones

Midea

Midea SV 4.45 wi Manual de usuario

LG LDF7932 Manual de usuario

Gorenje

Gorenje GV63214 Manual de usuario

Hotpoint

Hotpoint HDA1100ZWH Manual de servicio

Blomberg

Blomberg LDFN2240W Manual de usuario

AEG

AEG FFB83836PM Manual de usuario

Cylinda

Cylinda DM3220RFD Manual de usuario

Atag

Atag DW8214MB Manual de usuario

GE GLD8000 Series Manual de usuario

Siemens

Siemens SN23HI02KE Hoja de especificaciones

Omega

Omega ODW717X Manual de usuario

BORETTI

BORETTI BVW-683 Manual de usuario

Siemens

Siemens SN 56N591 Manual de usuario