Electrolux Dishlex DX303 Manual

dimension & installation guide

built-under dishwasher – DX303

IMPORTANT

• These instructions are a guide only. For complete

installation instructions, refer to the manual provided with

the product.

• If you do not follow the installation instructions your

dishwasher will not be properly installed.The product

warranty does not cover incomplete or improper

installation.You will be charged a service fee for any service

call to rectify improper or incomplete installation.

• These instructions apply to built-under applications only.

DISHWASHER DIMENSIONS

The dimensions shown below are in millimetres.

The height of 820mm is with the levelling legs

screwed in all the way.

TYPICAL BUILT-UNDER INSTALLATION

CUPBOARD OPENING DIMENSIONS

The dimensions shown below are in millimetres.The opening

allows for some clearance so that the dishwasher can be

pushed into place.

Note: if the opening is greater than 600mm wide then a suitable

width ﬁller piece should be secured to the cupboard before

installing the dishwasher.

820mm

180mm

50mm

100mm

595mm

120mm

555mm edge of door

585mm centre of doo

825mm min.

880mmmax.

585mm

600mmmin.

Do not install tapsor

power points in this space

1000mm max

Secure dishwasher with

brackets and screws provided

Gap on both sides

should be equal and no greater

than 3mm maximum per side

Kickplate fixing screws

If floor is not level, adjust

levelling legs to suit

600mm max -

300mm min

POWER SUPPLY

230/240V–10Amps

TAP CONNECTION

If cold-water pressure is

in excess of 800kPa, a

pressure-reducing valve

should be used.

Check for leaks.

INLET WATER SUPPLY

Water flow rate 10L/minute min

Water temperature 60°C max

Water pressure cold water:

800kPa max - 50kPa min

Water pressure hot water:

350kPa max - 50kPa min

Cold water recommended

(Refer page 3 for further information)

The hose should not be

extended by more than

2 metres or water pump-out

problems may occur

There should be a minimum

2mm gap between the top of

the dishwasher and

underside of bench top

Fix drain hose max of

10mm below the top of

the dishwasher

Remove entire plastic

membrane from sink trap

spigot & fit drain hose to

spigot with clamp

DISHWASHER

POWER OUTLET

SINK

page 1

dimension & installation guide

built-under dishwasher – DX303

page 2

LEVELLING

Good levelling is essential for correct closure and sealing of

the door.

When the appliance is correctly levelled, the door will not

catch or rub on either side of the cabinet.

Leave a space of 2mm between the top of the dishwasher

and the underside of the kitchen counter.

SECURING THE DISHWASHERSecure the dishwasher

by screwing it ﬁrmly in position under the bench or to the

cupboard beside it (refer to diagram on previous page). Use

the angular brackets supplied which are ﬁtted into the slots on

top of the dishwasher (more detail is shown in the caution note

below).Tighten the machine in position (upwards or sideways)

by using the screws supplied (3.5 x 16mm).Tighten the screws

so that the dishwasher cannot tip forward and cause damage

when the door is open and the baskets are fully loaded.

CAUTION

The dishwasher must be secured to the underside of

the worktop or to adjacent cupboards by using the

brackets supplied.

Failure to do this can cause injury or damage.

Under no circumstances may holes be drilled

through the sides of the dishwasher since this could

damage the hydraulic components.

CAUTION

Carefully follow the instructions on the template

enclosed with the product for building the

dishwasher under a counter.

No further openings for venting of the dishwasher

are required, but only to let the water ﬁll and drain

hose and power supply cable to pass through.

The height of the recess where the dishwasher is to be installed

can vary between 825mm and 885mm from the ﬂoor since the

dishwasher is ﬁtted with adjustable feet (max.60mm).

Leave a space of 2mm between the top of the dishwasher and

the underside of the kitchen counter.

FITTING THE STEAM PROTECTION

Fit the steam protection onto the front part of the worktop,

using the screws provided.

Check if the dishwasher

is levelled

600mm

825-880mm

600mm

dimension & installation guide

built-under dishwasher – DX303

page 3

CONNECTION TO WATER SUPPLY

The inlet hose should be inspected every 12 months for

deterioration and replaced if necessary.

• Cold water connection

– We recommend connection to a cold water supply.

– Water pressures between 50kPa and 800kPa are

acceptable.

– A pressure-reducing valve must be ﬁtted if the cold

water supply can exceed 800kPa. (Refer also to the

remarks in the section below concerning water hammer.)

• Hot water connection

Hot water connection is an option, providing the supply

conforms to the following conditions:

– The maximum permissible temperature for the hot

supply is 60oC. Any higher temperature may cause

damage to water carrying components and dishware life

may be reduced.

– If your dishwasher is likely to be connected to a solar

hot water system, drip heater or similar system, the

temperature must not exceed 60°C.Where it is

anticipated that the temperature will exceed 60°C, a

water temperature tempering valve should be installed

in the water service.

– Water pressures between 50kPa and 350kPa are

acceptable. A pressure-reducing valve must be ﬁtted

if the hot water supply can exceed 350kPa.

• Water hammer

Quick action household taps and fast acting water valves

on appliances can cause water hammer.This can result in

very high water pressures. High pressure can cause failure

of the pressure reducing valve (where ﬁtted), or the water

valve in your dishwasher.

To prevent water hammer, we recommend the ﬁtment

of a Noise Reduction Valve in the water suppy line.These

valves also act as a pressure reducing valve with the added

beneﬁts of:

– reducing the chance of a burst hose; and

– reducing the water noise whilst the dishwasher is ﬁlling

with water.

Pressure reducing valves, water temperature tempering

valves and noise reduction valves are available from major

plumbing suppliers. DO NOT connect your dishwasher to

the outlet of an unpressurised displacement instantaneous

water heater (for example a push-through type sink

heater) as damage to the heater may result.

IMPORTANT

• Ensure that hoses are not crushed or kinked under or

behind the dishwasher.

• After connecting hose to the tap, turn the tap on and

check to ensure that there are no leaks.

dimension & installation guide

built-under dishwasher – DX303

page 4

CONNECTING THE DRAIN HOSE

• The drain hose must be free of kinks and obstructions.

• The highest point of the hose should not be more than

1 metre from the ﬂoor and should have a continous fall.

• The drain hose may be lengthened using additional lengths

and connectors, which can be purchased from Electrolux

Spare Parts. The extension length must not exceed

2 metres.

Remove internal membrane from drain spigot.

When connecting the drain hose to an under sink trap spigot,

the entire plastic membrane must be removed.

Failure to remove all the membrane will result in food particles

building up over time eventually blocking the dishwasher drain

hose spigot.

KICKPLATE ADJUSTMENT

If your dishwasher is supplied with a kickplate panel, you may

need to adjust the height of the kickplate to cover the gap at

the bottom front of the dishwasher.

To adjust the height:

• Loosen the two screws that secure the kickplate.

• Reposition the panel.

• Secure the kickplate with the two screws.

CUSTOM-MADE KICK PANEL

On built-under and full stainless steel door models,for best

cosmetic appearance,we recommended that you manufacture a

custom-made kick panel that matches your kitchen cabinetry.

• A notched continous panel is required to prevent door swing

inteference and to maintain kick panel alignment with adjacent

cabinets.

• Cut a notch in the kick-panel deep enough to allow the door to

swing freely under the dishwasher.

• Check for inteference by slowly opening and closing the door.

If the door touches the kick panel,trim to prevent inteference.

• Secure the kick panel to adjacent cabinets in such a manner that

it may be removed if service is required.

ELECTRICAL CONNECTION

WARNING

• Safety standards require the appliance to be earthed.

• Prior to using the appliance for the ﬁrst time, ensure

that the rated voltage and type of supply on the rating

plate match that of the supply where the appliance is

to be installed.The fuse rating is also found on the

rating plate.

• Always plug the mains plug into a correctly installed,

approved socket.

• Multi-way plugs, connectors and extension cables must

not be used.This could constitute a ﬁre hazard through

overheating.

• If necessary, have the domestic power outlet replaced. If

the electrical supply cord has to be replaced, contact your

local Customer Care centre.

• The plug must be accessible after the appliance has been

installed.

• Never unplug the appliance by pulling on the cable. Always

pull the plug.

• Ensure that the dishwasher has been tested using the rinse

& hold or quick 30 cycle and that the dishwasher ﬁlls with

water, washes and drains with no leaks.

The manufacturer accepts no liability for failure to observe the

above safety precautions.

Remove entire

internal membrane

DISH303INSTALL_Jul07

Otros manuales para dishlex DX303

Tabla de contenidos

Otros manuales de Lavavajillas de Electrolux

Electrolux

Electrolux ESF 66814 Manual de usuario

Electrolux

Electrolux Zanussi DE 6854 Manual de usuario

Electrolux

Electrolux ESF 43010 Manual de usuario

Electrolux

Electrolux ASF47005 Manual de usuario

Electrolux

Electrolux FAVORIT 40760 Manual de usuario

Electrolux

Electrolux FSE73700P Manual de usuario

Electrolux

Electrolux ESF 66814 Manual de usuario

Electrolux

Electrolux ESI66050 Manual de usuario

Electrolux

Electrolux EDW5505EPS - ICON - Dishwasher Manual de usuario

Electrolux

Electrolux EUC1G 400063 Manual de instrucciones

Electrolux

Electrolux ESF5542LOW Manual de usuario

Electrolux

Electrolux WTCS140 Manual de usuario

Electrolux

Electrolux ICON EDW5500DSS0 Manual de usuario

Electrolux

Electrolux GA55SLV Manual de usuario

Electrolux

Electrolux ESL 7310RO Manual de usuario

Electrolux

Electrolux EEM69410W Manual de usuario

Electrolux

Electrolux ESF675 Manual de usuario

Electrolux

Electrolux ESF 64010 Manual de usuario

Electrolux

Electrolux 152981 73/0 Manual de usuario

Electrolux

Electrolux ESF4100 Manual de usuario

Electrolux

Electrolux ESI 67010 Manual de usuario

Electrolux

Electrolux KEAF7200L Manual de usuario

Electrolux

Electrolux EWDW6505 Manual de usuario

Electrolux

Electrolux ESL 63010 Manual de usuario

Manuales populares de Lavavajillas de otras marcas

KitchenAid

KitchenAid KUDB230B Manual de usuario

Brandt

Brandt BDJ424DB Manual de usuario

Asko

Asko DSD767UXXL.AU Manual de usuario

Beko

Beko DFN26210W Manual de usuario

NEFF

NEFF S153ITX00E Hoja de especificaciones

Midea

Midea SV 4.45 wi Manual de usuario

LG LDF7932 Manual de usuario

Gorenje

Gorenje GV63214 Manual de usuario

Hotpoint

Hotpoint HDA1100ZWH Manual de servicio

Blomberg

Blomberg LDFN2240W Manual de usuario

AEG

AEG FFB83836PM Manual de usuario

Cylinda

Cylinda DM3220RFD Manual de usuario

Atag

Atag DW8214MB Manual de usuario

GE GLD8000 Series Manual de usuario

Siemens

Siemens SN23HI02KE Hoja de especificaciones

Omega

Omega ODW717X Manual de usuario

BORETTI

BORETTI BVW-683 Manual de usuario

Siemens

Siemens SN 56N591 Manual de usuario

Electrolux dishlex DX303 Manual

Manuales populares de Lavavajillas de otras marcas