ElectrIQ eiQCURV60EN Manual de usuario
2
CONTENTS
IMPORTANT SAFETY INFORMATION
3
PARTS
5
INSTALLATION OF FLAPS
6
EXTERNAL VENTILLATION
7
INSTALLATION
7
EXHAUST INSTALLATION
11
OPERATION
12
GREASE MESH FILTERS
12
CARBON FILTER
13
REPLACING THE BULB
14
CLEANING AND MAINTENANCE
15
TROUBLESHOOTING
16
SPECIFICATION AND SUPPORT
17
PRODUCT FICHE
18
3
IMPORTANT SAFETY INFORMATION
Please read this instruction manual carefully and retain
for future reference. It contains important information
concerning the safe operation, installation and
maintenance of the appliance.
• There must be adequate ventilation of the room when
the hood is used at the same time as appliances
burning gas or other fuels.
• This cooker hood is only designed for domestic use,
and should not be used in a commercial environment.
• Never use the hood for any purpose other than its
intended use.
• Do not check the status of the filters during operation of
the cooker hood.
• Do not touch the light bulb within 30 minutes of use.
• Do not flambé or excessively flame under the hood.
• Never leave frying food unattended as it can be a
serious fire hazard.
• If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or a similarly
qualified person in order to avoid a hazard.
• The socket outlet for the hood must be located so it is
easily accessible for the user after installation.
• Ensure the mains supply voltage corresponds with that
of the appliance.
• There is a fire risk if cleaning is not carried out in
accordance with the instructions.
• Ensure that the socket used provides adequate earthing
of the appliance, if unsure professional advice must be
sought.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
4
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
• Children must not play with the appliance.
• Cleaning and user maintenance must not be carried out
by children without supervision.
• When the hood is being maintained, cleaned or filters
changed, make sure it is switched off at the mains
supply.
• The exterior of the hood should be cleaned with mild
detergent on a warm damp sponge or cloth.
• The air must not be discharged into a flue that is used
for exhausting fumes from appliances burning gas or
other fuels.
• Regulations concerning the discharge of air have to be
fulfilled.
• The minimum distance between the supporting surface
for the cooking vessels on the hob and the lowest part
of the hood must be at least 65 cm.
• When the cooker hood is used in conjunction with
appliances supplied with energy other than electric, the
negative pressure in the room must not exceed 0,04
mbar to prevent fumes being drawn back into the room
by the cooker hood.
• Failure to install the hood in accordance with these
instructions may result in electrical hazards.
CAUTION:
Accessible parts may become hot when used with
cooking appliances.
Deep fat fryers must be continuously monitored during
use: overheated oil can burst into flames.
5
PARTS
DESCRIPTIONILLUSTRATIONQTY
Cooker Hood 1
Glass Canopy
1
Chimney Sections (Pair) 1
Outlet 1
Air Flap 2
Chimney bracket 1
Canopy Anti vibration ring 4
Canopy Mounting washer 4
Bolt (M4*20) 4
Screw (ST4*40) 2
Screw (ST4*30) 4
Wall plug 6
Screw (ST4*8) 4
Exhaust Adaptor 1
6
INSTALLATION OF THE FLAPS
The 2 air flaps should now be installed on the top of the unit, as access
is easier before the unit is wall mounted. The flaps should be carefully
installed, bending them slightly so the lugs at each end locate into the
holes in the outlet vent. When the unit is in operation the flaps pivot
upwards to allow airflow.
Please note: Ensure the small lugs at each end of each flap locate into
the holes on the housing and not the grooves above them.
After installing the flaps, ensure that they are able to pivot freely within
the outlet, before fixing the air outlet to the top of the unit using 2 x ST4*8
Screws.
7
OPTIONS FOR VENTILATION
This hood can be set up for either external venting or recirculation of the
air. The type of setup should be decided before commencing
installation.
EXTERNAL VENTING
If you have an outlet leading outside, your
cooker hood can be connected as shown in the
diagram using a flexible exhaust pipe.
Alternatively, any suitable extraction duct
(enamel, aluminium, flexible pipe or
inflammable material with an interior diameter
of 120/150mm) can be used.
An adaptor is also supplied to enable you to
connect your hood to pre-existing 120mm
diameter ducting.
If this is the chosen installation method, consideration to the route of the
vent pipe should be made prior to installation.
NOTE: the performance of the hood may be affected if the diameter of
the pipe is reduced, or if the airflow is restricted.
RECIRCULATION
This cooker hood also supports the
recirculation of air once it has passed through
the filters. The filtered air is then expelled
through the vent holes in the side of the
chimney.
When setting the unit up in this configuration,
carbon filters should also be used to remove
odors from the air. Details of fitting the filters
can be found in the Carbon filter section.
When setting up for recirculation the installation instructions should be
followed, but the vent pipe should not be attached, allowing the air to be
expelled through the vents on the side of the chimney.
8
INSTALLATION
• Unpack the hood and check that all functions are working. Ensure that
the voltage (V) and the frequency (Hz) indicated on the serial plate
match the voltage and frequency at the installation site.
• Check that the area behind the installation surface is clear of any
electrical cables or pipes, etc to avoid damage when drilling.
• The surfaces of the hood can be very easily damaged during installation.
Take care with tools to protect the surfaces during installation.
• Protect the hob surface with cardboard, or similar, to prevent damage
occurring whilst the hood is being installed above.
• The manufacturer shall not be liable for any failure to observe all
safety regulations in force for the correct and normal operation of
electrical products.
• Ensure the wall is level and the installation plates are horizontal to
prevent grease from accumulating within the hood.
• Ensure the power has been turned off at the mains before starting
installation.
• Connection to the mains supply must be in an accessible location.
• You may need the following tools to complete this installation:
• Drill appropriate for your wall
• Phillips Screwdriver
• Tape Measure
• Electrical wiring must be done by a qualified professional in accordance
with all applicable codes and standards, including fire rated construction.
IMPORTANT
• Sufficient air is needed for proper combustion and exhaustion of gases
through the flue (chimney) for fuel burning equipment to prevent back
drafting. Ductless fans must always be vented to the outdoors.
• When assessing the air pressure, the entire ventilation system in the
house/apartment must be taken into account.
• All legal regulations must be observed for the conveyance of exhaust air.
If the extractor hood is used in recirculating mode with the optional
carbon filter, there are no operating restrictions.
9
1. Before installation, ensure
you have not connected
the appliance to the
mains supply.
2. The cooker hood should
be placed at a distance of
65~75cm above the
cooking plane for best
effect.
3. After confirming the
height of the cooker
hood measure the
position of the
holes inside and
outside of the
chimney bracket for
hanging the hood.
4. Drill 4 holes, 2 for
the inner chimney
bracket and 2 for
hanging the hood, and keep the hood level.
The inner chimney bracket should be
secured at the highest point.
5. Screw two 4 x 30mm screws on the wall with wall plugs to fix the
hood, then use two 4mm x 40mm screws to fix the inner chimney
bracket.
10
6. Place the glass canopy on to the
hood, aligning the screw holes.
Place the anti-vibration rings into
the 4 holes before securing the
glass canopy into place by
tightening the 4 bolts (M4*20)
through the mounting rings into
the hood.
7. Then fix the outlet on the hood
and attach the adaptor.
8. Hang the hood on the wall in the desired
final position.
9. Once the hood is positioned
correctly, fix the unit to the wall
using 2 x ST4*30 screws and wall
plugs through the fixing holes.
The fixing holes are located inside
the unit behind the grease filters.
10. Place the two chimneys together
onto the cooker hood body. Adjust
the height of the inner chimney
until a suitable height. Fix the inner
chimney to the chimney bracket
using the supplied screws
(ST4*8).
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Campana de ventilación de ElectrIQ
ElectrIQ
ElectrIQ eiQCHIM60SC Manual de usuario
ElectrIQ
ElectrIQ eiQSRG60 Manual de usuario
ElectrIQ
ElectrIQ eiQCANOPY70TM Manual de usuario
ElectrIQ
ElectrIQ eiQ60PBSLIMEN Manual de usuario
ElectrIQ
ElectrIQ eiQCHA90B Manual de usuario
ElectrIQ
ElectrIQ eiQCANOPY52S Manual de usuario
ElectrIQ
ElectrIQ eiQCH110CEILING Manual de usuario
ElectrIQ
ElectrIQ ISLAND eiQTMISLANDSLIM Manual de usuario
ElectrIQ
ElectrIQ EIQ90CANGW Manual de usuario
ElectrIQ
ElectrIQ eiQCHFGBSS60 Manual de usuario
ElectrIQ
ElectrIQ eiQ80CURVSCTM Manual de usuario
ElectrIQ
ElectrIQ eiQ60touchslimhe Manual de usuario
ElectrIQ
ElectrIQ eiq90chimbl Manual de usuario
ElectrIQ
ElectrIQ eiQ52GCANOPY Manual de usuario
ElectrIQ
ElectrIQ eiQCURV60SCTOUCH Manual de usuario
ElectrIQ
ElectrIQ eiQ52CANGW Manual de usuario
ElectrIQ
ElectrIQ eiQCURV60SC Manual de usuario
ElectrIQ
ElectrIQ eiQTOPVWHITE Manual de usuario
ElectrIQ
ElectrIQ eiQCHDD60 Manual de usuario
ElectrIQ
ElectrIQ eiQCHB60B Manual de usuario
