ELECRAFT K3S Manual de instrucciones

Elecraft • www.elecraft.com • 831-763-4211

Technical content subject to change without notice

For more information, please contact: [email protected]

K3SFrequently Asked Questions

Ver. C 5/12/15

!"#$%&'()*+*,-./0*1234%56)0*7849**:22*;&'()<*;3<3%=3>*

?@A*B383%52*CD3<)&"8<*

Q: What are the new features of the Elecraft K3S?

A: The K3Sis Elecraft’s second-generation, software-defined superhet transceiver (SDR).

We’ve upgraded nearly every subsystem, improving performance and adding many new

features. Here’s a quick overview:

New Features

Benefits

Ultra-low-noise synthesizer

Unequaled strong-signal receive performance; exceptional transmit

signal purity.

Second preamp (Preamp 2)

Built-in equivalent of Elecraft’s PR6-10 low-noise amplifier (LNA)

for weak-signal work on 12, 10, and 6 m. Preamp 2 is part of the

KXV3B module (now included as a standard feature). The

KXV3B also provides RX antenna in/out jacks, transverter in/out

jacks, and a buffered IF output for use with our P3 panadapter.

Multiple attenuation levels

Attenuation levels of 0, 5, 10, and 15 dB; selectable per-band.

Dual computer ports (USB

and RS232)

In addition to the legacy RS232 port, the new USB port integrates

computer remote control and line-level audio. This eliminates the

need for a sound card or external converters and their associated

cables. Supports Windows, Linux and Apple platforms.

KAT3A option now

includes bypass relay

Lower loss on bands where matched antennas are used.

Redesigned speaker

amplifier

Stereo speaker outputs now have lower total harmonic distortion

(THD) for reduced listening fatigue.

Fast transmit/receive

switching

High-accuracy CW transmit timing—even at high code speeds with

SPLIT, RIT, and XIT in use.

Extended coverage includes

630 and 2200 meter bands

When used with the KBPF3A option, receiver covers 630 m (472

kHz), and 2200 m (137 kHz), tuning as low as 100 kHz. Transmit

output of 0.5-1.0 mW on 630 m (for use with an external amplifier).

Enhanced look and feel

New LCD bezel; soft-touch VFO A knob with improved grip.

Elecraft • www.elecraft.com • 831-763-4211

Technical content subject to change without notice

For more information, please contact: [email protected]

Q: What components have been changed for the K3S? Are they available for the K3?

A: Nearly all internal modules have been upgraded for the K3S. Some of the modules that are

compatible with the K3 are already available:

K3S

Module

New Features

Available now?

KSYN3A

•Very low close-in phase noise

•Faster T/R switching

•VFO tuning down to 100kHz (with KBPF3A)

Yes

Kits available for order now.

Please order KSYN3AUPG

KXV3B

•Built-in low noise preamp for 12/10/6 m

Yes

Kits available for order now.

KAT3A

Includes true bypass relay for lower loss with well-

matched antennas

Yes

Kits available for order now.

KRX3A

Sub receiver now includes KSYN3A synthesizer.

Yes

Kits available for order now.

KBPF3A

Redesigned filter extends Very Low Frequency

(VLF) operation down to 100 kHz.

Yes

Kits available for order now.

Q: Will any other K3Smodules or components be made available for K3 use?

A: Yes. The following additional K3Smodules and components are compatible with the K3,

and will be offered once excess inventory is available for upgrade purposes:

K3S

Module

New Features

When Available?

KIO3B

•Adds direct USB connection

•Eliminates need for PC soundcard and cables

•RS232 connection remains supported; adapter cable

included with K3S

Available later this year

Main DSP

board

Enhanced speaker amplifier with low-distortion pre-

driver.

Available later this year

Soft-touch

VFO A band

•Updated design with new grip pattern

•Softer material for improved tuning feel

Available later this year

Elecraft • www.elecraft.com • 831-763-4211

Technical content subject to change without notice

For more information, please contact: [email protected]

Q: What modules are unique to the K3S?

A: These upgraded modules (and components) are unique to the K3Sand will not be available

for K3 upgrades:

K3S

Module

What has changed

Unique to

the K3S?

K3SRF Board

•Added 5/10/15dB Attenuator

•Lower RF and digital noise floor

•Better port-to-port isolation

Yes

K3SFront Panel

board

Real-time clock frequency adjustable; calibrated

at factory to better than +/- 0.5 sec./day

Yes

Front Panel sheet

metal

Updated silkscreen

Yes

K3SLCD/VFO bezel

New single-piece molded bezel with logo and

integrated VFO pointer

Yes

Q: Will my existing crystal filters work with the K3S?

A: Yes, all K3 crystal filters are fully compatible with the K3S. They are configured in the

same way.

Q: With the K3S, will I need to keep track of another set of firmware revisions?

A: No. New firmware releases will determine automatically whether you are using a K3Sor a

K3, and will support both original and upgraded modules. There will be no change in the

numbering of these combined K3S/K3 firmware releases. You will be able to use K3 Utility

to manage firmware updates for both transceivers.

Q: Will K3Sserial number sequencing change?

A: Yes. K3Sserial numbers will begin at 10000.

Elecraft • www.elecraft.com • 831-763-4211

Technical content subject to change without notice

For more information, please contact: [email protected]

?@A*<D##"%)*6"%*?EF&83*#%">D4)<*58>*#3%&#(3%52<*

(KPA500, KAT500, P3, P3/SVGA)

Q: What has changed on the rear panel of the K3S?

A: The most important change is to the communication ports in the upper right corner of the

rear panel. This is where the new USB connector is located. The original RS232 port functions

are preserved, though with a different jack type (RJ45) and a supplied DE9 adapter cable. The

accessory jack (ACC) is unchanged.

The included adapter cable (shipped with the K3S) duplicates the original 9-pin RS232 port, so

you can continue to use all of your station accessories as before.

The illustration below shows the rear panel of the K3S. The fan panel shown is supplied with

100-W model.

Q: Can the KPA500 and KAT500 be used unchanged with the K3S?

A: Yes. The K3Ssupports these K-Line products. All cabling will remain the same as you see

in the KAT500 and KPA500 Owner’s Manuals.

Q: Will the P3 operate with the K3Sin the same way?

A: Yes. The K3Swill support the P3 using the same cables you are using now for your P3

connections, with the addition of a supplied RJ45-to-DE9 adapter.

Q: How can I operate the P3 and use the new USB port at the same time?

A: To use both USB connectivity and the P3, you’ll need a new cable, CBLP3Y. The

CBLP3Y cable will enable direct USB connection while accommodating full P3 support.

The CBLP3Y cable will be available directly from Elecraft. Price and availability will be

announced prior to K3Sshipments.

Elecraft • www.elecraft.com • 831-763-4211

Technical content subject to change without notice

For more information, please contact: [email protected]

Q: What will happen to the K3 now that the K3Sis available?

A: With the introduction of the K3S, the K3 is no longer available. Elecraft production has

already switched to the K3S.

Q: Now that there’s the K3S, what should I expect for support of the K3?

A: Elecraft will continue to honor all warranties and will continue to fully support the K3.

There is no change to this policy in any way. Anyone who has purchased a K3 will

continue to receive email support and firmware updates when they are made available.

Q: How long should I expect to get parts and email support for the K3?

A: Currently, there are no changes planned for parts and support for the K3 for the foreseeable

future.

Q: Will Elecraft still provide phone call and email support for the K3?

A: Yes, there are no changes planned for parts and support for the K3 for the foreseeable

future.

Q: Will the K3/0 Mini and Remote system work with the K3S?

A: Yes, all cabling and Remote System products will work with the K3S.

Otros manuales para K3S

Tabla de contenidos

Otros manuales de Transceptor de ELECRAFT

ELECRAFT

ELECRAFT K2 Manual de usuario

ELECRAFT

ELECRAFT K3 Guía de inicio rápido

ELECRAFT

ELECRAFT K3S Manual de usuario

ELECRAFT

ELECRAFT K3 Manual de usuario

ELECRAFT

ELECRAFT KX3 Manual de usuario

ELECRAFT

ELECRAFT P3 Manual de usuario

ELECRAFT

ELECRAFT KX3 Instrucciones de funcionamiento

ELECRAFT

ELECRAFT K4 Manual de usuario

ELECRAFT

ELECRAFT K3S Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

ELECRAFT

ELECRAFT KX1 Manual de usuario

ELECRAFT

ELECRAFT K3 Manual de usuario

ELECRAFT

ELECRAFT K3 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

ELECRAFT

ELECRAFT K2 Manual de usuario

ELECRAFT

ELECRAFT XV50 Manual de usuario

ELECRAFT

ELECRAFT K3 Manual de usuario

ELECRAFT

ELECRAFT K2 Manual de usuario

ELECRAFT

ELECRAFT K3 Manual de usuario

ELECRAFT

ELECRAFT KBPF3 Manual de usuario

ELECRAFT

ELECRAFT K3 Manual de usuario

ELECRAFT

ELECRAFT KX3 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

ELECRAFT

ELECRAFT K3 Manual de usuario

Manuales populares de Transceptor de otras marcas

Yaesu

Yaesu FT-7B Manual de usuario

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario

Uniden

Uniden UH820 Series Manual de usuario