Elation PROTEUS RAYZOR 1960 Manual de usuario

User Manual

PROTEUS

RAYZOR 1960

images, and instructions herein are subject to change without notice. ELATION PROFES-

SIONAL logo and identifying product names and numbers herein are trademarks of ELATION

PROFESSIONAL. Copyright protection claimed includes all forms and matters of copyrightable

materials and information now allowed by statutory or judicial law or hereinafter granted.

Product names used in this document may be trademarks or registered trademarks of their

respective companies and are hereby acknowledged. All non-ELATION brands and product

names are trademarks or registered trademarks of their respective companies.

ELATION PROFESSIONAL and all a󰤳liated companies hereby disclaim any and all liabilities

for property, equipment, building, and electrical damages, injuries to any persons, and direct

or indirect economic loss associated with the use or reliance of any information contained

within this document, and/or as a result of the improper, unsafe, insu󰤳cient and negligent

assembly, installation, rigging, and operation of this product.

Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040

323-582-3322 | 323-832-9142 fax | www.elationlighting.com | info@elationlighting.com

Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands

+31 45 546 85 66 | +31 45 546 85 96 fax | www.elationlighting.eu | info@elationlighting.eu

Elation Professional Mexico

AV Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Date Document

Version

Software

Version DMX Channels Notes

09/08/2022 1.0 2.0.0 25 / 100 / 176 ch. Initial Release

09/21/2022 1.1 N/C No Change Updated Installation,

Specifications

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version

of this document may be available online.

Please check www.elationlighting.com for the latest revision/update of

this manual before beginning installation and/or programming.

TABLE OF CONTENTS

Introduction 4

Warranty Returns 6

Safety Precautions 7

Maintenance Guidelines 9

Overview 11

Installation 12

Torque Settings for Screws 20

Remote Device Management (RDM) 22

Control Panel 23

System Menu 24

Record Controller 27

Fan Control and Low Noise Operation 29

Lighting Console Patching Guidelines 30

DMX Traits 35

FX Generator Guidelines 46

RGBW Pixel FX Table 47

Spark LED FX Table 52

Waveforms 56

Dimmer Curves 57

Color Temperature Table 58

Primary-Secondary Set Up 60

Error Codes 61

Software Update 62

Dimensional Drawings 63

Specifications 65

FCC Statement 66

Please read and understand the instructions in this manual carefully and thoroughly before

attempting to operate this device. These instructions contain important safety and use infor-

mation. This device is intended for use by trained personnel only, and is not suitable for

private use.

UNPACKING

Every device has been thoroughly tested and has been shipped in perfect operating condition.

Carefully check the shipping carton for damage that may have occurred during shipping. If the

carton is damaged, carefully inspect the device for damage, and be sure all accessories neces-

sary to install and operate the device have arrived intact. In the event that damage has been

found or parts are missing, please contact our customer support team for further instructions.

Please do not return this device to your dealer without 󰤱rst contacting customer support.

Please do not discard the shipping carton in the trash. Please recycle whenever possible.

IP65 RATED

An IP rated lighting 󰤱xture is commonly installed in outdoor environments and has been designed

with an enclosure that e󰤰ectively protects the ingress (entry) of external foreign objects such

as dust and water. The International Protection (IP) rating system is commonly expressed as

“IP” followed by two numbers (i.e. IP65) where the numbers de󰤱ne the degree of protection.

The 󰤱rst digit (Foreign Bodies Protection) indicates the extent of protection against particles

entering the 󰤱xture, while the second digit (Water Protection) indicates the extent of pro-

tection against water entering the 󰤱xture. An IP65 rated lighting 󰤱xture, such as this one,

has been designed and tested to protect against the ingress of dust (6) and low-pressure

water jets from any direction (5).

BOX CONTENTS

Power Cable (x1)

CUSTOMER SUPPORT

Contact ELATION Service for any product related service and support needs.

Also visit forums.elationlighting.com with questions, comments or suggestions.

ELATION SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

323-582-3322 | Fax 323-832-9142 | support@elationlighting.com

ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

+31 45 546 85 63 | Fax +31 45 546 85 96 | support@elationlighting.eu

REPLACEMENT PARTS - please visit parts.elationlighting.com

INTRODUCTION

LENS POSITION FOR SHIPPING AND PACKAGING:

When re-packaging this 󰤱xture for shipping or transportation, the device must be placed

securely into the form-󰤱tting foam in-lay (FIL) that was included in the box when the 󰤱xture

was 󰤱rst purchased. Please refer to the Dimensional Drawings section of this manual for

detailed information about the foam in-lay.

Additionally, it is CRITICALLY IMPORTANT to orient the head of the 󰤱xture so that the lens

is pointing toward the base of the unit, as illustrated below. Failure to do so can result in

damage to the 󰤱xture’s zoom function while in transit. Reminder notices will be stamped

into the foam in-lay itself as a precautionary measure.

WARRANTY RETURNS (USA ONLY)

To obtain warranty service, a Return Materials Authorization (RMA) number must first be

obtained from ELATION. It is the Customer’s responsibility to provide product proof of

purchase and serial number by acceptable evidence such as an invoice copy or an approved

ELATION Extended Warranty Certificate (“EWC”) and any relevant maintenance records at the

time warranty service is sought. Failure to provide acceptable evidence of product proof of

purchase or EWC and any relevant maintenance records may be cause for denial of warranty

service.

Products returned for warranty service must be sent without any accessories (i.e., power,

data, and safety cables, brackets, clamps, rigging hardware, frost filters, gel frames, barn

doors, lens, hoses, nozzles, rack mounting hardware, etc.), must be boxed using the original

and/or suitable packaging materials (double-box and foam) that provides ample product pro-

tection for ground and/or air freight transit, and must be shipped freight pre-paid and insured

to ELATION in Los Angeles, CA or an ELATION Authorized Service Center. The RMA number

must be clearly written on the outside of the return box, and a brief description of the prob-

lem and the RMA number must be documented and included in the box.

Products returned for warranty service without an RMA number clearly marked on the out-

side of the package will be refused and returned to the shipper at the Customer’s expense.

Products returned for warranty service, which are received damaged due to inadequate and/

or improper packaging and/or due to damage caused by shipping carrier, may incur addi-

tional repair charges before warranty service begins and/or may void this warranty. If any

product accessories (included and/or optional) are shipped with the product, ELATION and/

or the ELATION Authorized Service Center shall have no liability what so ever for the loss

and/or damage to any such accessories, nor the safe return thereof. If the requested war-

ranty repairs or service (including parts replacement) are within the terms of this warranty,

ELATION will pay return ground transportation shipping charges to a single designated point

within the United States.

SAFETY PRECAUTIONS

PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED.

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT

ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S

WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE

AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS

MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO

ANY WARRANTY CLAIMS AND/OR REPAIRS.

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!

RETINA INJURY RISK - MAY INDUCE BLINDNESS!

SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

This 󰤱xture is a sophisticated piece of electronic equipment. To guarantee a smooth opera-

tion, it is important to follow all instructions and guidelines in this manual. Elation Profes-

sional is not responsible for injuries and/or damages resulting from the misuse of this 󰤱xture

due to the disregard of the information printed in this manual. Only quali󰤱ed and/or certi󰤱ed

personnel should perform installation of this 󰤱xture and only the original rigging parts in-

cluded with this 󰤱xture should be used for installation. Any modi󰤱cations to the 󰤱xture and/

or the included mounting hardware will void the original manufacturer’s warranty and in-

crease the risk of damage and/or personal injury

DO NOT PLUG FIXTURE INTO A DIMMER PACK!

NEVER OPEN THIS FIXTURE WHILE IN USE!

UNPLUG POWER BEFORE SERVICING FIXTURE!

NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT! KEEP

FLAMMABLE MATERIALS AWAY FROM FIXTURE!

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A

DIELECTRIC GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT

WATER CORROSION AND/OR ELECTRICAL SHORT CIRCUIT.

MINIMUM DISTANCE TO OBJECTS/SURFACES

MUST BE 3.3 FEET (1 METER)

MAXIMUM TEMP OF EXTERNAL SURFACE 185° F (85°C)

MINIMUM DISTANCE OF FLAMMABLE MATERIALS FROM THE SURFACE 1.6 FEET

(0.5 METER)

SAFETY PRECAUTIONS

• DO NOT TOUCH the 󰤱xture housing during operation. Turn OFF the power and allow ap-

proximately 15 minutes for the 󰤱xture to cool down before servicing.

• DO NOT shake 󰤱xture, and avoid using brute force when installing and/or operating the

󰤱xture.

• DO NOT operate the 󰤱xture if the power cord is frayed, crimped, damaged, and/or if any

of the power cord connectors are damaged and do not plug into the 󰤱xture securely with

ease.

• NEVER force a power cord connector into the 󰤱xture. If the power cord or any of its con-

nectors are damaged, replace it immediately with a new one of the same power rating.

• DO NOT block any air ventilation slots.

• All fan and air inlets must remain clean and never blocked.

• Leave approx. 6” (15cm) between the 󰤱xture and other devices or a wall in order to allow

for proper cooling.

• Always disconnect the 󰤱xture from the main power source before performing any type of

service and/or cleaning procedure.

• Only handle the power cord by the plug end. Never pull out the plug by tugging on the wire

portion of the cord.

• During the initial operation of this 󰤱xture, a light smoke or smell may emit from the inte-

rior of the 󰤱xture. This is a normal process and is caused by excess paint in the interior of

the casing burning o󰤰 from the heat associated with the lamp. This will decrease gradually

over time.

• Consistent operational breaks will ensure 󰤱xture will function properly for many years.

• ONLY use the original packaging and materials to transport the 󰤱xture for service.

MAINTENANCE GUIDELINES

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

CLEANING

Frequent cleaning is recommended to ensure proper function, optimized light output, and an

extended life. The frequency of cleaning depends on the environment in which the 󰤱xture

operates: damp, smoky or particularly dirty environments can cause greater accumulation of

dirt on the 󰤱xture’s optics. Periodically clean the external lens surface with a soft cloth to

avoid dirt/debris accumulation. NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to insure proper function and extended life. There are

no user serviceable parts inside this 󰤱xture. Please refer all other service issues to an autho-

rized Elation service technician. Should you need any spare parts, please order genuine parts

from your local Elation dealer.

Please refer to the following points during routine inspections:

• A detailed electric check by an approved electrical engineer every three months, to make

sure the circuit contacts are in good condition and prevent overheating.

• Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall

out during normal operation, resulting in damage or injury as larger parts could fall.

• Check for any deformations on the housing, color lenses, rigging hardware, and rigging

points (ceiling, suspension, trussing). Deformations in the housing could allow for dust to

enter into the 󰤱xture. Damaged rigging points or unsecured rigging could cause the 󰤱xture

to fall and seriously injure a person(s).

• Electric power supply cables must not show any damage, material fatigue or sediments.

NEVER remove the ground prong from the power cable.

FIXTURE DISASSEMBLY

The following points should be observed after performing any maintenance procedure that

requires disassembly of the unit:

• After the unit has been reassembled, open the valve and allow the unit to run for approxi-

mately 2 hours in order to dry out any moisture that has been trapped inside the 󰤱xture.

The process should continue until indicated humidity drops below 15% for the head and

30% for the base.

• Once this has been achieved, the light can be switched o󰤰, but the unit should remain

connected to power so that the cooling fan can cool down the unit. Please note that al-

lowing cool down time should ALWAYS be done after lamp operation.

• Some units may require partial disassembly in order to gain access to the valve. Please

contact Elation service for information regarding the location and access procedure for

the valve on your speci󰤱c unit model.

MAINTENANCE GUIDELINES

BATTERY REPLACEMENT

Installing the battery in the incorrect orientation will lead to internal electron-

ics and battery damage. A quali󰤱ed electrician should be used for all electrical

connections and/or installations.

Follow the directions below to replace the battery:

1. Loosen the screw cap for the battery compartment, as shown below to the left.

2. Remove old battery and replace. Make sure the battery is oriented with the negative

“-” terminal towards the inside and the positive “+” terminal towards the outside.

Refer to the illustration below to the right.

3. Replace and tighten screw cap to secure the battery in place.

NOTE: Replace the battery only with an Li-ion battery (IRC14500/700mAh), which can be

ordered from the Elation Parts Website.

https://parts.elationlighting.com/catalog/product/view/id/18373/s/60420050026/cat-

egory/2/

Tabla de contenidos

Otros manuales de Equipo de DJ de Elation

Elation

Elation ARISTE MONET EAM990 Manual de usuario

Elation

Elation KL FRESNEL 8 Manual de usuario

Elation

Elation RAYZOR 360Z Manual de usuario

Elation

Elation KL FRENSEL 4 Manual de usuario

Elation

Elation Elation Professionals T20F Manual de usuario

Elation

Elation ZCL BAR Z300 IP Manual de usuario

Elation

Elation PLATINUM SPOT LED PRO II Manual de usuario

Elation

Elation 1236100115 Manual de usuario

Elation

Elation VOLT Q5E SIX PACK Manual de usuario

Elation

Elation SNIPER PRO Manual de usuario

Elation

Elation FUZE SPOT Manual de usuario

Elation

Elation Active Wave 250 Manual de usuario

Elation

Elation SIX PAR Z19 IP Manual de usuario

Elation

Elation RDMX6S Manual de usuario

Elation

Elation PALADIN CUBE Manual de usuario

Elation

Elation WW PROFILE HP Manual de usuario

Elation

Elation FUZE WASH FR Manual de usuario

Elation

Elation HAZE 400 Manual de usuario

Elation

Elation DARTZ 360 Manual de usuario

Elation

Elation TVL SOFTLIGHT DW Manual de usuario

Elation

Elation CYBER PAK Manual de usuario

Elation

Elation ARTISTE PICASSO Manual de usuario

Elation

Elation SATURA PROFILE Manual de usuario

Elation

Elation DTW BLINDER 350 IP Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario

KAM

KAM DMX Laser80 FScan Manual de usuario