Eguana Technologies ENDURO Manual de instalación

DO 67-020

Installation & Start-up Guide

For use only with battery type

LG Chem EM048126P3S7

ENDURO

Home Energy Storage System

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important instructions for the Enduro™ Home Energy Storage System. The

Eguana Enduro™ components described by this manual are intended to be used as part of an Energy

Storage system.

CAUTION: Hazardous Voltages! This inverter contains hazardous voltage and energy that

may be lethal. It may only be installed by qualified personnel who have read this manual and are

familiar with its operation and hazards. The following safety procedures should be followed:

1 Only connect the system to a compatible electrical service as defined in the model specifications.

The system must be connected to a dedicated branch circuit in the main electrical panel.

CAUTION! This equipment contains high energy lithium batteries. Qualified and trained

personnel should wear protective clothing and equipment when working inside the battery cabinet

and/or with battery modules.

2 This product is compatible with the LG Chem battery model EM048126P3S7 only.

CAUTION! The battery provided with this system must be charged only by the PCS included

as part of the energy storage system. Do not attempt to charge batteries with any other charger

device or connect any devices directly to the DC battery bus.

3 Ensure proper electrical grounding in accordance with code requirements.

4 Ensure proper airflow path for active cooling.

5 Never operate system in a manner not described by this manual.

6 Only qualified personnel should service this product.

7 Ensure all covers are securely fastened after installation is complete.

8 This product must be stored indoors in an environmentally conditioned location prior to installation,

protected from rain and exposure to any hazardous chemicals.

9 Do not attempt to operate this product if there is any physical evidence of damage to any of the

cabinets or internal components.

CAUTION! This equipment is heavy. Handle with care.

Contents

1 SAFETY.................................................................................................................................................................................................1

1.1 IN CASE OF EMERGENCY................................................................................................................................1

1.2 BATTERY MODULE SAFETY PRECAUTIONS.......................................................................................................1

1.3 GENERAL SAFETY PRECAUTIONS....................................................................................................................2

1.4 ENVIRONMENTAL PROTECTION......................................................................................................................2

2 INTRODUCTION ....................................................................................................................................................................................3

2.1 ABOUT THIS MANUAL –TARGET AUDIENCE ....................................................................................................3

2.2 GLOSSARY ...................................................................................................................................................3

2.3 SPECIAL TOOLS &HARDWARE........................................................................................................................3

2.4 INITIAL INSPECTION OF MATERIAL LIST...........................................................................................................4

ENERGY MANAGEMENT SYSTEM COMPONENTS.....................................................................................................4

3 INSTALLATION SITE PREPARATION ................................................................................................................................................5

3.1 INSTALLATION CLEARANCES...........................................................................................................................5

3.2 INSTALLATION PLAN –POWER AND COMMUNICATION CIRCUITS.........................................................................6

4 ENDURO INSTALLATION INSTRUCTIONS ........................................................................................................................................7

4.1 SECURING THE ENDURO TO THE WALL. ..........................................................................................................7

4.2 MOUNTING THE BATTERY MODULE .................................................................................................................7

5 BATTERY CONNECTIONS ..................................................................................................................................................................8

5.1 POWER CABLE CONNECTION..........................................................................................................................8

5.2 COMMUNICATION CABLE CONNECTION...........................................................................................................8

6 SYSTEM ELECTRICAL WIRING..........................................................................................................................................................8

6.1AC WIRING –TT, TNNETWORKS...................................................................................................................9

..........................................................................................................................................................................9

7 ENERGY METER INSTALLATION........................................................................................................................................................9

..........................................................................................................................................................................9

7.1 ENERGY METER LOCATION.............................................................................................................................9

7.2 ELECTRICAL CONNECTIONS –VOLTAGE MEASUREMENT /POWER SUPPLY.......................................................10

7.3 CT (CURRENT TRANSFORMER)CONNECTIONS ..............................................................................................10

7.4 RS-485 COMMUNICATION CONNECTION .......................................................................................................10

8 ENDURO EMS INSTALLATION ..........................................................................................................................................................11

8.1 ENDURO EMS INSTALLATION PROCEDURE ...................................................................................................11

8.2 EMS ETHERNET CONNECTION.....................................................................................................................11

9 START-UP SEQUENCE......................................................................................................................................................................12

10 OPERATION......................................................................................................................................................................................12

11 PCS DISPLAY PANEL......................................................................................................................................................................12

11.1 LED DISPLAY INDICATORS ........................................................................................................................12

11.2 LED DISPLAY DEFINITIONS.........................................................................................................................12

12 EMERGENCY POWER OUTLET.......................................................................................................................................................13

13 MAINTENANCE ................................................................................................................................................................................13

14 TROUBLESHOOTING ......................................................................................................................................................................13

15 TECHNICAL DATA ...........................................................................................................................................................................14

1 Safety

Throughout this manual, the following symbols will be used to highlight important information and procedures:

Symbol

Definition

Symbol

Definition

WARNING! A dangerous voltage or other

condition exists. Use extreme caution when

performing these tasks.

operating status

CAUTION! This information is critical to the safe

installation and or operation of the inverter.

Follow these instructions closely.

NOTE: This statement is important. Follow

instructions closely.

1.1 In case of emergency

In all cases:

If safe to do so, switch off the AC breakers (external to the system) for the system.

Contact the fire department or other required emergency response team.

Evacuate the area, and if applicable, follow your emergency evacuation plan if others are in proximity to the

installed location.

In case of fire:

When safe, use a fire extinguisher suitable for use; including A, B, and C dry chemical fire extinguishers or

carbon dioxide extinguishers.

In case of flooding:

Stay out of water if any part of the system or wiring is submerged.

Do not attempt to operate batteries that have been submerged in water even after they have been dried.

In case of unusual noise, smell or smoke:

If safe to do so, ventilate the area.

1.2 Battery module safety precautions

This product is integrated with LG Chem EM048126P3S7 series battery modules. Refer to the LG Chem product manual

LG Chem P3S series 48V Standalone Battery Module Installation Manual, for complete safety instructions regarding

handling of battery modules.

EMS

1.3 General safety precautions

Important! Installation, service, and operating personnel must read this document in its entirety, and observe all safety

and installation procedures as described in this manual. Never operate system in a manner not described by this manual.

Only qualified personnel should service this product.

Ensure all covers are securely fastened after installation is complete.

Personal Protective Equipment (PPE) in compliance with local work place safety standards must be worn when working

inside the cabinet.

Risks of Fire

Do not expose the system to temperatures exceeding 60 degrees Celsius.

Avoid installation in direct sunlight.

Do not store objects on top of the cabinet.

Do not obstruct the intake or exhaust of the forced airflow system.

Do not store combustible objects and corrosive chemicals directly adjacent to the system.

Risks of Shock

WARNING! Hazardous Voltages. The Inverter contains hazardous voltage and energy that may be lethal.

It may only be installed by qualified personnel who have read this manual and are familiar with its operation and

hazards.

Only connect the PCS cabinet to a compatible electrical service as defined in the model specifications. The PCS

must be connected to a dedicated branch circuit in the main electrical panel.

Ensure proper electrical grounding in accordance with code requirements.

CAUTION! Both AC and DC voltage sources are terminated inside this equipment. Each circuit must be

individually disconnected before servicing.

Risks of Damage

The PCS is compatible with the LG Chem battery model EM048126P3S7 only. Do not attempt to connect any

other battery to the system.

Do not connect any other loads directly to the battery power bus.

Do not drop, tip, or puncture the cabinet during transport and installation. Visible damage to the cabinet and/or

internal components should be reported to the manufacturer immediately.

Do not store this system for periods longer than six months without a battery maintenance charge. This may

result in permanent damage to the batteries.

1.4 Environmental Protection

Do not dispose of the system or any of the components within the cabinet. Batteries, electronics, cables, and metal parts

are recyclable. Consult your municipal waste management authority to determine required methods of component

recycling.

2 INTRODUCTION

2.1 About this Manual –Target Audience

This manual is intended to be used by qualified service and installation personnel for the purposes of product installation.

This manual contains instructions for the installation and start up sequence of the Eguana Enduro™home energy storage

system; including the ESS, the energy management system, the energy meter(s), and the ethernet connection to a customer

supplied internet router. This product is permanently wired to the home electrical service and must be installed by a licensed

electrician only.

The energy management system relies on an AC coupled PV solar source to charge the batteries as part of the energy

management control algorithms. A utility interconnected PV solar system must be installed in conjunction with this energy

storage system for the self-consumption algorithm to operate. This product can supply limited backup power via an on-

board 10A power outlet.

2.2 Glossary

2.3 Special tools & hardware

The following tools and materials are required for mounting of the Enduro ESS to the wall.

Mounting hardware for wall bracket (suited for wall material).

Drill and bits rated for mounting hardeware.

Level

#2 Philips screwdriver

Term

Definition

Term

Definition

Alternating Current

GND

Ground

ARC

Auto Recovery Circuit

IEC

International Electrotechnical Commission

AS/NZS

Standards Australia

LED

Light Emitting Diode

CEC

Clean Energy Council

Normally Closed

CPU

Central Processing Unit

Normally Open

Direct Current

PCS

Power Control System (Inverter)

DRED

Demand Response Enabling Device

Protective Earth

DRM

Demand Response Mode

Photo-Voltaic

EMS

Energy Management System

Radio Frequency

ESD

Electrostatic Discharge

SOC

State Of Charge (Battery)

ESS

Energy Storage System

SOH

State of Health (Battery)

User Interface

2.4 Initial Inspection of Material List

The system components supplied with your Eguana Enduro™

Energy Storage system are shown below. Each component should

be inspected visually for any damage that may have been caused by

shipment. If damage is present, please contact your local distributor.

Note: Battery shown for reference only, if supplied separately.

Energy management system components

*Energy meters and CTs as shown are subject to change.

Ref

Qty

Description

System

Energy Meter*

USB/RS-485 Adapter (1-main energy meter 1-Enduro EMS)

Enduro EMS

Enduro EMS Power Supply

CTs (3-ph mains metering –use only 1 CT for single phase installs)

DIN-rail mounting hardware. 2 ea - end blocks, 1 ea - ground.

Enduro EMS communication cable

Energy meter communication cable

USB Adapter to Enduro EMS USB cables

PV-Option –required for PV inverters without software integration to Enduro EMS

Energy Meter

USB/RS-485 Adapter

DIN-rail mounting hardware. 2 ea - end blocks, 1 ea - ground.

CTs (3-ph mains metering –use only 1 CT for single phase installs)

Energy meter communication cable

USB Adapter to Enduro EMS USB cable

3Installation Site Preparation

Before installing the Enduro home energy storage components, read all instructions and warnings in this manual.

IMPORTANT! All electrical installation work should be performed in accordance with local building and electrical

codes.

WARNING! Isolate the PCS from all energy sources prior to electrical installation by means of disconnects,

breakers or connectors. Failure to properly isolate either AC or DC sources may result in serious injury or death.

This system will generate an AC voltage at the off-grid terminals when DC source is applied.

CAUTION! The Enduro cabinet weighs up to 96 kg. Handle with care.

NOTE: All interconnecting cables are limited in length.

CAUTION! Do not install in direct sunlight or near sources of heat. Battery performance is dependent upon

operating ambient temperature. Radiant heat absorbed in direct sunlight will greatly reduce the performance of the

battery. The battery module is rated for operation between -10C to +40C. For long term performance, an ambient room

temperature between 15 to 30C is recommended.

3.1 Installation clearances

The physical installation of the cabinets requires the layout planning and installation of the system components in the

available installation space.

30 cm

15 cm

60 cm

Figure 1: Installation clearances.

3.2 Installation plan –power and communication circuits

The following example outlines the wiring plan for power and communication circuits.

Figure 2: Electrical single line diagram.

NOTES

1- The Enduro EMS panel can be installed in or near the electrical service panel. A maximum distance of 1 meter from the electrical panel is

recommended. Not shown: the EMS is powered by an adapter that plugs into a 230V outlet.

2 - Energy meter supports 1Ø and 3Ø configuration where applicable. Observe CT direction as shown.

3 - 3Ø service shown. For 1Ø service, do not populate R,S ph components. It is recommended that PV 1Ø connection is on the same

phase as the Enduro ESS (as shown).

4 –The battery system must be earth bonded to the building ground to meet lightning protection requirements.

Disclaimer:

Mfr supplied components represented here are limited to the Enduro ESS, Enduro EMS panel, EMS to ESS signal cables, and energy meter(s) with

signal cables, fuses and CTs for 1Ø or 3Ø service. All other materials and components represented are customer supplied. Electrical code compliance

is the responsibility of the designer and/or electrical permit holder.

4Enduro Installation Instructions

4.1 Securing the Enduro to the wall.

CAUTION! The Enduro is top heavy. Handle with care.

IMPORTANT! The wall anchor method used must be suitable for the wall material, and be rated to prevent the product from tipping

over.

Note: The wall bracket anchor centers are 116 cm from the floor (see photo 3 –right). Step 1 can be skipped if the floor is level and

flat. For best results, the following procedure is recommended.

1. Stand the Enduro upright and position against the

wall to which it will be mounted, marking the top edge

of the mounting bracket.

2. Pull the Enduro away from the mounting location and

remove the mounting bracket.

3. Using a level or straight edge for reference, position

the mounting bracket on the wall and mark the

centers for the wall anchors.

4. (Not shown): Insert the wall mount anchors and

mount the bracket to the wall.

5. Position the Enduro against the wall bracket, and

secure using the hardware provided.

4.2 Mounting the battery module

Note: The following instructions are applicable

where the battery is supplied separately from the

Enduro ESS. Proceed to section 6 if your battery

is pre-installed.

Note: Clear the battery power and communication

cables away from the mounting area of the battery

module.

1. Position the battery module into the base

of the Enduro’s frame, aligning the

brackets as shown right.

2. Secure the battery module using the two

mounting screws provided.

Figure 3: Wall-mounting the Enduro.

Figure 4: Mounting the battery.

Tabla de contenidos

Otros manuales de Accesorios de audio y vídeo de Eguana Technologies

Eguana Technologies

Eguana Technologies Evolve 0513 Manual de instalación

Manuales populares de Accesorios de audio y vídeo de otras marcas

enerserve

enerserve e.manager nD Manual de usuario

Starmatrix

Starmatrix Clever-Pool/220V Manual del propietario

TecnoVideo

TecnoVideo VSPT Series Manual de usuario

NeoVolta

NeoVolta NV14 Instrucciones de uso

Horizon Fuel Cell

Horizon Fuel Cell FCJJ-40 Manual de usuario

SC&T

SC&T CD108HD Manual de usuario

4-noks

4-noks PR-SA Guía rápida

PROAIM

PROAIM CINEMA Series Manual de usuario

Synergistic Research

Synergistic Research UEF ACOUSTIC DOTS Manual de usuario

Paso

Paso C571/6-V Manual de usuario

CMD

CMD bs6396 Manual de usuario

Bluetti

Bluetti EP600 Manual de usuario

Delta Electronics

Delta Electronics AFE075A43A Manual de usuario

Yamaha

Yamaha PTB-4210 Manual de usuario

Burst Electronics

Burst Electronics MCG-2 Manual de usuario

Panasonic

Panasonic DMP-BD60 - Blu-Ray Disc Player Manual de usuario

mind alive

mind alive Smart Manual de usuario

MagniLink

MagniLink S PREMIUM 2 MLS-HD-2 Manual de usuario