EGig EG1000T32-B Manual de usuario

10/100/1000Mbps

Gigabit Fast Ethernet Adapter

User's Manual

FCC Warning

This device has been tested and found to comply

with limits for a Class B digital device, pursuant to

Part 2 and Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference when the equipment

is operated in a commercial environment. This

equipment generates, uses and radiates radio

frequency energy and, if not installed and used in

accordance with the user's manual, may cause

interference in which case user will be required to

correct the interference at his own expense.

CE Mark Warning

This is a Class B product. In a domestic

environment, this product may cause radio

interference in which case the user may be

required to take adequate measures.

Table Of Contents

Chapter 1..............................................................1

Introduction....................................................1

KeyFeatures..................................................3

Chapter 2..............................................................4

PackageContents..........................................4

Chapter 3..............................................................5

Installation......................................................5

HardwareInstallation...............................5

DriverInstallation.....................................5

Chapter 4..............................................................6

LED Definitions..............................................6

FDX.........................................................6

100M.......................................................6

1000M.....................................................6

ACT..........................................................6

Chapter 5..............................................................7

Technical Specifications.................................7

II.

Chapter 1

10/100/1000Mbps Gigabit Fast Ethernet Adapter

Introduction

The Gigabit network adapter complies to 32/64 bit

PCI specification and supports half/full duplex

feature which can double network speed.

This adapter supports 1000Mbps (Gigabit),

100Mbps and 10Mbps network speed,

1000BASE-T operates on all four pairs of category

5 UTP cable, 100BASE-TX operates on two pairs

of category 5 UTP cable and 10BASE-T operates

on Category 3,4,5 UTP cable. With the Auto-

Negotiation technology, network speed is auto

detected.

When you connect the adapter to Gigabit Switch or

another Gigabit NIC, the speed will be doubled to

2000Mbps (1000Mbps Transmit and 1000Mbps

Receive). If you connect the adapter to

100BASE-TX hub, the network speed is 100Mbps.

Similarly, if the hub is a switching hub, which

supports full duplex function, then the speed will

be doubled to 200Mbps.

-1-

This adapter supplies many drivers including NDIS

4,5 driver for Microsoft Windows 98, Me, NT, 2000,

Unix/Linux, and Netware Server 4/5. Whatever

your requirements are ease of installation, superior

performance or responsive support backed up by

unlimited technical support, this adapter is the

superior choice.

-2-

Key Features

Supports 64/32-bit, 66/33MHz PCI Bus Master

for high performance

Full duplex design to double the performance to

20Mbps/200Mbps/2000Mbps

One STP connector for 1000Mbps, 100Mbps or

10Mbps network speed

Support Auto-negotiation function

Auto-setups IRQ and I/O address

Supports Virtual LAN (VLAN) and long frame

(1536Bytes)

Supports 802.1D and 802.1Q priority queuing

Net System: NDIS 4,5 driver for Microsoft

Windows 95/98, Win2000, Me, Netware driver

for Server V.4/5, UNIX, Linux

Supports MDIX at 10, 100, 1000Mb/s

Compliant with PC 97 and PC 98 Hardware

Design Guides, PC 99 Hardware Design Guide

draft. ACPI v1.0, PCI Power Management

Specification v1, OnNow Device Class Power

Management Reference Specification - Network

Device Class v1.0a

Supports Jumbo packets (9K)

Wake on LAN (WOL) support compliant with

PC98, PC99, and OnNow, including directed

packets, Magic Packet TM, ARP packets, pattern

mach packets, and Phy status change

IPv.4 checksum task off-loading

-3-

Chapter 2

Package Contents

Before you start to install the Gigabit Fast Ethernet

Adapter, please verify your package that contains

the following items:

One 10/100/1000Mbps Gigabit Fast Ethernet

Adapter

One User's Manual

One Floppy Disk

Note: If any of these items is found missing or

damaged, please contact your local supplier for

replacement.

-4-

Adapter

Disk

10/100/1000Mbps

User's Manual

Gigabit Fast Ethernet Adapter

Chapter 3

Installation

If you experience any problems with the adapter,

first please make sure the appropriate driver is

loaded, the proper cable is connected to the

adapter port and the Hub/Switch complies with the

adapter specification, such as 10Mbps 10BASE-T,

then 100Mbps 100BASE-TX and 1000Mbps

1000BASE-T, then check the LED.

I. Hardware Installation

To insert the network adapter into your PC, please

follow the steps as bellow:

Turn off the computer and remove the computer

cover.

Insert the adapter into a PCI slot.

Secure this adapter to the rear of the computer

chassis and put back the computer cover.

Connect the adapter to the network using

twisted-pair cable.

II. Driver Installation

Use the drivers supplied by the diskette included in

this product. For detail description, please execute

the readme.exe in the root directory of the diskette

provided by this product.-5-

3.

4.

Chapter 4

The adapter provides three LEDs to indicate

network status.

LED Definitions

FDX :The port is operating at Full-duplex.

:The port is operating at Half-duplex.

100M :100Mbps UTP port link ok.

:100Mbps UTP port has not been

connected or link is not ok.

1000M :1000Mbps UTP port link ok.

:1000Mbps UTP port has not been

connected or link is not ok.

ACT :The port is ready for 10/100/1000Mbps

connection.

:The port is transmitting or receiving

data.

-6-

off

flashing

ACT

1000M100M

FDX

ACT

1000M100M

FDX

Chapter 5

Technical Specifications

Standard:

-IEEE 802.3 10BASE-T; IEEE 802.3u 100BASE-

TX; IEEE 802.3ab 1000BASE-T

Connector

- RJ-45

Architecture

- PCI 2.1/2.2 (6/33MHz) 32bit & 64bit

Transmission Rate

-10/100/1000Mbps

Topology

- Star

Protocol

-CSMA/CD

Network Transmission Media

-10BASE-T Cat. 3, 4, 5 UTP/STP

-100BASE-TX Cat. 3, 4, 5 UTP/STP

-1000ASE-TX Cat. 5, 6 UTP/STP

LEDs

-ACT, 100M, 1000M, FDX

Power Consumption

- 7 Watts (Max)

Operating Temperature

- 0 C~ 55 C

Store Temperature

- -20 C~ 70 C

-7-

10.

11.

Tabla de contenidos

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario

EGig eG1000T32-B Manual de usuario

Manuales populares de Adaptador de otras marcas