Edge BH 69 Manual del propietario

SPECIFICATION



Wingspan : 1,580 mm 62.20 in.



Length : 1,400 mm 55.12 in.



Weight : 3.6 kg 7.26 Lbs.



Radio : 06 channels.



Servo : 06 servos.



Engine : 61-75 2 stroke.

91 4 stroke.

Instruction Manual book

MadeinVietnam.

EDGE - Item code: BH69 . Instruction Manual

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your EDGE. Use the parts listing below to identify

all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedtohelpthenew pilotonhiswaytosuccessfulR/C flight.Theywillalso beable

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modellingknife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

Some more parts.

HARDWAREPACK

COWLING.

Landinggear.....

Toavoid scratching yournew airplane,donot

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the air-

craftand toprotect thetable.Keepacoupleof

jars or bowls handy to hold the small parts af-

ter you open the bag.

Pleasetrialfitalltheparts. Makesureyouhave

the correct parts and that they fit and are

alignedproperly beforegluing!Thiswillassure

proper assembly. EDGE ARF is hand made

from natural materials, every plane is unique

andminor adjustmentsmayhave tobe made.

However, you should find the fit superior and

assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the follow-

ing:paintthinner,C/Aglueaccelerator,C/Aglue

debonderandacetone. Donotletthesechemi-

cals come in contact with the colors on the

covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage.

WING ASSEMBLY

(1) Right wing half with pre-installed

aileron.

(1) Left wing half with pre-installed

aileron.

Tail section assembly

(1) Vertical stabilizer with pre-

installedrudder.

(1) Horizontal stabilizer with pre-

installedelevator halves.

SUGGESTION.

NOTE.

EDGE - Item code: BH69 . Instruction Manual

+ This is not a toy

+ Be sure that no other flyers are using your

radio frequency.

+ Do not smoke near fuel

+ Store fuel in a cool, dry place, away from

children and pets.

+ Wear safety glasses.

+Theglowplug clipmustbesecurely attached

to the glow plug.

+ Do not flip the propeller with your fingers.

+ Keep loose clothing and wires away from

thepropeller.

+ Do not start the engine if people are near.

Donot standinlinewiththesideof thepropel-

ler.

+ Make engine adjustments from behind the

propeller only. Do not reach around the spin-

ningpropeller.

SAFETY PRECAUTION.

REPLACEMENT LARGE PARTS

B. Wing panel.

C. Fuselage.

A.Cowling.

D . Horizontal stabilizer.

F. Aluminium wing dihedral

brace.

E.Vertical stabilizer.

G.Decal sheet.

REPLACEMENT SMALL PARTS

1) Install the rubber grommets and brass

eyelets onto the aileron servos.

1.INSTALLING THE AILERON SERVOS.

I. AILERON.

Aileron

Top side.

Aileron Bottom side

C/Aglue

Bottom side

D. E.

EDGE - Item code: BH69 . Instruction Manual

C/Aglue

3) Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

Remove

covering

2.Usinga modelingknife,remove thecov-

ering servo tray.

4. Drill 1,5mm pilot holes through the block

of wood for each of the four mounting screws

provided with the servo. Install servo into ai-

leron servo tray as same as picture below.

Aileron

Bottom side

C/Aglue

Electric wire

Thread

EDGE - Item code: BH69 . Instruction Manual

3 x 40mm.

Nilon control clasp.M3lock nut.

INSTALLINGTHEAILERON CONTROLHORN.

Removecovering

EDGE - Item code: BH69 . Instruction Manual

Repeat the procedure for the other wing

half.

Installing the aileron linkages as pictures

below.

INSTALLING THE AILERON

LINKAGES.

M3 M3 lock nut

C/Aglue

70mm

EDGE - Item code: BH69 . Instruction Manual

Repeat the procedure for the other wing

half.

INSTALLING THE ENGINE MOUNT.

See pictures below:

INSTALLING THE STOPPER ASSEMBLY

FUEL TANK.

4x30mm

1. The stopper has been pre-assembled at

the factory.

2.Using amodeling knife,cut onelength of

siliconfuelline (thelength ofsilicon fuellineis

calculated by how the weighted clunk should

restabout 8mmaway fromtherearofthetank

andmove freelyinside thetank). Connectone

end of the line to the weighted clunk and the

otherend tothenylonpickuptubein thestop-

per.

3.Carefully bendthesecond nylontube up

ata 45degreeangle (usingacigarettelighter).

This tube will be the vent tube to the muffler.

Drillahole4mm

diameter

Silicon tube not included

EDGE - Item code: BH69 . Instruction Manual

 5. Test fit the stopper assembly into the

tank. It may be necessary to remove some of

the flashing around the tank opening using

amodeling knife. Ifflashing is present, make

sure none of it falls into the tank.

 8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole

in the firewall. Pull the lines out from behind

the engine, while guiding the fuel tank into

place. Push the fuel tank as far forward as

possible,the frontofthetankshould justabout

touch the back of the firewall.

6. When satisfied with the alignment of the

stopper assembly tighten the 3mm x 20mm

machine screw until the rubber stopper ex-

pandsand sealsthetank opening.Do notover

tighten the assembly as this could cause the

tank to split.

7. Using a modeling knife, cut 3 lengths of

fuel line 150mm long. Connect 2 lines to the 2

vent tubes and 1 line to the fuel pickup tube in

the stopper.

Blow through one of the lines to ensure

the fuel lines have not become kinked inside

the fuel tank compartment. Air should flow

througheasily.

9. To secure the fuel tank in place, apply a

bead of silicon sealer to the forward area of

thetank, whereit exitsthefuselage behindthe

enginemountingbox andtotherearofthetank

at the forward bulkhead.

Do not secure the tank into place perma-

nently until after balancing the airplane.

You may need to remove the tank to mount

the battery in the fuel tank compartment.

When the stopper assembly is installed

in the tank, the top of the vent tube should

rest just below the top surface of the tank.

It should not touch the top of the tank.

4. Carefullybend thethirdnylon tubedown

ata 45degreeangle (usingacigarettelighter).

This tubewill bevent tubeto thefuelingvalve.

EDGE - Item code: BH69 . Instruction Manual

Locate the long piece of wire used for the

throttlepushrod. Oneendofthewire hasbeen

pre-bend in to a “Z” bend at the factory. This

“Z” bend should be inserted into the throttle

armofthe enginewhentheengine isfittedonto

theengine mount.Fittheengineto theengine

mount using the screws provided.

Markpoint

4 x 30mm

Pushrod wire.

Fueltank

115mm

INSTALLING THE ENGINE.

Drill a hole 4mm

diameter

EDGE - Item code: BH69 . Instruction Manual

Left side

Secure

1. Slide the fiberglass cowl over the en-

gineand lineup thebackedgeofthe cowlwith

the marks you made on the fuselage.

COWLING.

2. While keeping the back edge of the

cowl flush with the marks, align the front of

thecowlwiththecrankshaftoftheengine. The

front of the cowl should be positioned so the

crankshaft is in nearly the middle of the cowl

opening. Hold the cowl firmly in place using

pieces of masking tape.

3. Slide the cowl back over the engine

andsecure itin placeusing fourwood screws.

See picture below.

4. Installthemufflerandmufflerextension

onto the engine and make the cutout in the

cowl for muffler clearance. Connect the fuel

and pressure lines to the carburetor, muffler

andfuel fillervalve.

Trim and cut

Botom side

Right side

Left side

Otros manuales de Juguete de Edge

Edge

Edge BH92-A Manual del propietario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario