Edelbrock Qwikdata 91195 Manual de usuario

Rev. 6/03

Edelbrock Corporation, 2700 California Street, Torrance, CA 90503

Tech Line: 800-416-8628; Office: 310-781-2222

Edelbrock Qwikdata Shaft Speed Sensor Kit

Catalog # 91195 & 91196

INSTALLATION INSTRUCTIONS

•PLEASE study these instructions carefully before installing your new Edelbrock Qwikdata Shaft Speed Sensor Kit. If you have any

questions or problems, do not hesitate to contact our Technical Hotline at: 1-800-416-8628, from 7am-5pm, Monday through

Friday, Pacific Standard Time, or via e-mail at: [email protected].

•DESCRIPTION

The Edelbrock Qwikdata Shaft Speed Sensor Kit allows users

of the Qwikdata data aquisition system or other data

aquisition systems to mount up to 4 magnets in an aluminum

ring to the rear end pinion yoke on a Ford 9” housing.

Part #91195 will mount to most standard Ford 9” rear

housings with a 1.875” diameter pinion yoke. Part #91196

will fit 2.187” diameter, 35 spline yokes. Installation Procedure

•Note: Refer to Figure 1 below for reference on all steps.

1. Install the number of magnets you require for your data

aquisition system into the ring assembly.

2. The magnets are to be seated against the shoulder (towards

the outside diameter of the ring), then glued with an adhesive

such as epoxy, RTV silicone, hot glue, etc. (Note: Some

computers are sensitive to the magnet’s north and south

poles. Install magnets per requirements for your data

aquisition system.)

3. Install the ring halves around the pinion coupler and tighten

the 10-32 x 3/4” cap screws tightly. The beveled edge of the

•Kit Contents:

1 - Two-Piece Aluminum Mounting Ring

2 - 10-32 x 3/4” Cap Screws

4 - Magnets

1 - Sensor Switch Bracket

1 - Sensor Switch

Tighten so that the

gaps are even

Use a washer .060”-.080” thick to prevent

interference with the pinion support radius

Grip Diameter

Be sure the magnets are

seated against the outside

shoulder of the ring

Beveled edge should

face Pinion U-Joint

Set gap at .060”-.100” for

Qwikdata use

Set gap per data aquisition system

per manufacturer’s instructions

Note: Some multi-magnet sensors are pole-sensitive

and must be installed in correct +/- sequence.

FIGURE 1

Fill cavities with

epoxy or silicone

to secure magnets

inside of the ring should face the pinion U-joint. The gap on

each side of the ring should be even to ensure correct timing

on multiple magnet use.

4. Attach the Sensor Switch Bracket to a bolt or stud on the rear

end housing as shown in Figure 1. Attach Sensor Switch and

adjust gap to .060”-.100” for Qwikdata use, or to your data

aquisition system specification.

•Note: Periodically,makesurethemagnetsandmountingring

are secure.

•Caution: Excessive heat can cause the magnets to lose

power.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Pieza de automóvil de Edelbrock

Edelbrock

Edelbrock 5204 Manual de usuario

Edelbrock

Edelbrock 5247 Manual de usuario

Edelbrock

Edelbrock 66662 Manual de usuario

Edelbrock

Edelbrock 1727 Manual de usuario

Edelbrock

Edelbrock 2838 Manual de usuario

Edelbrock

Edelbrock 66152 Manual de usuario

Edelbrock

Edelbrock Nitrous Refill Station 78000 Manual de usuario

Edelbrock

Edelbrock 262-400 Manual de usuario

Edelbrock

Edelbrock 6510 Manual de usuario

Edelbrock

Edelbrock 4790 Manual de usuario

Edelbrock

Edelbrock Performer RPM Series Manual de usuario

Edelbrock

Edelbrock 6606 Manual de usuario

Edelbrock

Edelbrock Square-Bore Carb 2696 Manual de usuario

Edelbrock

Edelbrock 5419 Manual de usuario

Edelbrock

Edelbrock 78001 Manual de usuario

Edelbrock

Edelbrock 70005 Manual de usuario

Edelbrock

Edelbrock 72230 Manual de usuario

Edelbrock

Edelbrock 1926 Manual de usuario

Edelbrock

Edelbrock 7577 Manual de usuario

Edelbrock

Edelbrock 66332 Manual de usuario

Edelbrock

Edelbrock 72279 Manual de usuario

Edelbrock

Edelbrock Russell R08364 Manual de usuario

Edelbrock

Edelbrock 66092 Manual de usuario

Edelbrock

Edelbrock 5282 Manual de usuario

Manuales populares de Pieza de automóvil de otras marcas

Dakota Digital

Dakota Digital 650277 Manual de usuario

bosal

bosal 037031 Manual de usuario

Vintage Air

Vintage Air 571063 Manual de usuario

GFB

GFB EX38 Manual de usuario

bosal

bosal 028091 Manual de usuario

Dodge

Dodge 8W-43 Guía de inicio rápido

ICI

ICI Magnum FBM10DGN Manual de usuario

Volant Perfomance

Volant Perfomance 19435 Manual de usuario

BENDIX

BENDIX GEN 4 GEN 5 ABS Manual de usuario

Vintage Air

Vintage Air 571065 Manual de usuario

Rugged Ridge

Rugged Ridge 11503.13 Manual de usuario

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manual de usuario

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Guía

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manual de usuario

Toshiba

Toshiba 48-1250 A Manual de usuario

aldes

aldes EHT2 Manual de usuario

Go Rhino

Go Rhino 24371T Manual de usuario

BBK

BBK 18950 Manual de usuario