Edelbrock 67322 Manual de usuario

Catalog #67322 Page 1of 2 Rev. 10/03

Edelbrock One-Piece Pro-Flo Header

For 1994-2001 Acura Integra GS, RS, LS (Non-VTec)

Catalog #67322

INSTALLATION INSTRUCTIONS

Please study these instructions carefully before installing your new Pro-Flo Header. They provide general guidelines to

be studied and understood before you remove your stock system. Failure to follow these instructions may void your

warranty. If you have any questions or problems, please contact our Technical Hotline at : 1-800-416-8628 from

7 am – 5 pm, Monday through Friday, Pacific Standard Time or e-mail us at [email protected]. Please fill out

and mail your warranty card.

DESCRIPTION: Edelbrock Pro-Flo header components are designed to improve the exhaust efficiency of the Acura 1.8L

engines. A performance gain can be expected with the installation of the system. This system requires no welding for

installation and retains all stock emissions equipment.

Suggested tools needed for installation: This vehicle has some metric fasteners.

❑3/8” ratchet socket set with extensions and a good assortment of metric sockets

❑Combination wrenches (metric)

❑Universal 12mm and 14mm swivel sockets

❑Jackstands, screwdrivers, pliers, crescent wrench, etc.

❑Liquid penetrant (GM #1052627 or equivalent); anti-seize compound (GM #5613695 or equivalent)

SPECIAL NOTICE: This Edelbrock part has received an Executive Order number (E.O.#) from the California Air Resources

Board (C.A.R.B.) making it legal for street use in all 50 states. To assist you with emission equipment certification, we

have included a silver fan shroud decal to help testing personnel verify the this part is a legal replacement on the vehicle

for which it is cataloged. The adhesive-backed decal should be affixed next to the existing emission and engine

specifications decal. Do not cover any part of your original emission decal.

WARNING: The use of "Thermal Wrap" or any aftermarket coating process will void the warranty on your Edelbrock

Headers. Those products will cause excessive heat and moisture buildup resulting in corrosion and failure of the header.

INSTALLATION INSTRUCTIONS

DISASSEMBLY

1. Disconnect battery negative cable from battery.

2. Raise vehicle and support with jackstand.

3. The use of penetrating oil when removing and

the use of anti-seize compound when installing

nuts and bolts will prevent the possibility of

broken or stripped nuts and bolts.

4. Make sure converter is cool.

5. Remove O2 sensor (if applicable) being careful

not to destroy or rupture the unit.

WARNING: Do not clean this unit in any

cleaning solvents and do not rupture wire.

6. Remove the two nuts from hanger bracket.

Remove the two bolts and springs at the

catalytic converter. Then unbolt the three bolts

at the mid-section of manifold and remove lower

portion of manifold (B-section).

Catalog #67322 Page 2of 2 Rev. 10/03

KIT CONTENTS

Catalog #67322

Qty. Part # Description

125-9358 Pro-Flo One-Piece Header

122-6730 Installation Kit

Edelbrock Corporation

2700 California St.

Torrance, CA 90503

Tech Line: 1-800-416-8628

Office: 310-781-2222

E-Mail: [email protected]

ASSEMBLY

1. Install the header assembly from bottom side

with gasket and 9 hardened washers (supplied

in kit), using factory bolts/nuts as applicable.

Use anti-seize on threads.

2. With donut in place, connect header to catalytic

converter using stock hardware.

3. Install O2 sensor, if equipped. Use anti-seize on

threads of sensor and torque to 30 ft. lbs.

DISASSEMBLY (Continuation)

7. Remove the bolt that is attached to the engine

block in the lower section of manifold. Remove

bolts from manifold at cylinder head and pull

manifold out from top side. Note: Save all factory

nuts, bolts and springs to be used during re-

assembly.

Tabla de contenidos

Otros manuales de Pieza de automóvil de Edelbrock

Edelbrock

Edelbrock 68732 Manual de usuario

Edelbrock

Edelbrock 1115 Manual de usuario

Edelbrock

Edelbrock 3550 Manual de usuario

Edelbrock

Edelbrock 5752 Manual de usuario

Edelbrock

Edelbrock For 1985-1992 GM Cars and Trucks 17933 Manual de usuario

Edelbrock

Edelbrock Kawasaki KFX400 Manual de usuario

Edelbrock

Edelbrock Russell R09430 Manual de usuario

Edelbrock

Edelbrock 15017 Manual de usuario

Edelbrock

Edelbrock 68792 Manual de usuario

Edelbrock

Edelbrock 24502574 LT4 Manual de usuario

Edelbrock

Edelbrock 70027 Manual de usuario

Edelbrock

Edelbrock Russell R08367 Manual de usuario

Edelbrock

Edelbrock 1472 Manual de usuario

Edelbrock

Edelbrock 5282 Manual de usuario

Edelbrock

Edelbrock Victor Jr. 289-302 Manual de usuario

Edelbrock

Edelbrock 5292 Manual de usuario

Edelbrock

Edelbrock 2103 Manual de instrucciones

Edelbrock

Edelbrock 2WD 350 V8 Manual de usuario

Edelbrock

Edelbrock PERFORMER-PLUS 2182 Manual de usuario

Edelbrock

Edelbrock Performer RPM 351-W Ford V8 Manual de usuario

Edelbrock

Edelbrock 33505 Manual de usuario

Edelbrock

Edelbrock 460 Ford Manual de usuario

Edelbrock

Edelbrock 5658 Manual de usuario

Edelbrock

Edelbrock 5713 Manual de usuario

Manuales populares de Pieza de automóvil de otras marcas

Dakota Digital

Dakota Digital 650277 Manual de usuario

bosal

bosal 037031 Manual de usuario

Vintage Air

Vintage Air 571063 Manual de usuario

GFB

GFB EX38 Manual de usuario

bosal

bosal 028091 Manual de usuario

Dodge

Dodge 8W-43 Guía de inicio rápido

ICI

ICI Magnum FBM10DGN Manual de usuario

Volant Perfomance

Volant Perfomance 19435 Manual de usuario

BENDIX

BENDIX GEN 4 GEN 5 ABS Manual de usuario

Vintage Air

Vintage Air 571065 Manual de usuario

Rugged Ridge

Rugged Ridge 11503.13 Manual de usuario

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manual de usuario

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Guía

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manual de usuario

Toshiba

Toshiba 48-1250 A Manual de usuario

aldes

aldes EHT2 Manual de usuario

Go Rhino

Go Rhino 24371T Manual de usuario

BBK

BBK 18950 Manual de usuario