Edelbrock 5726 Manual de usuario

EDELBROCK CAT-BACK EXHAUST SYSTEM

For 1998-2001 DODGE RAM

5.2L & 5.9L V8, 2 & 4 wheel drive

Catalog #5726

INSTALLATION INSTRUCTION

Please study these instructions carefully before installing your new Cat-Back Exhaust System. If you

have any questions or problems, contact ourTechnical Hotline at: 1-800-416-8628 from 7 am - 5 pm,

Monday through Friday, Pacific Standard Time or e-mail us at: [email protected].

SUGGESTED TOOLS FOR INSTALLATION:

3/8" ratchet set with SAE and metric sockets

9/16” and 15mm wrenches

Jackstands and jack

Liquid penetrant and rubber lubricant

DISASSEMBLY

1. Raise vehicle and support with proper jackstands for the weight, leaving the suspension hanging.

2. Use caution around hot exhaust systems to avoid burns.

3. Use penetrating oil on all nuts and bolts.

4. Remove the bolts and clamps from the system and lubricate the rubber hangers.

5. Use a long pry bar to pull the rubber hangers off of the pipe hangers.

6. Remove the old system. In some cases, you will find it easier to cut the overaxle pipe to remove

it. Note: On some vehicles, the removal of the straight pipe behind the cat-converter will not be

necessary. The new I-pipe will slip onto the outlet of the pipe that is changed onto the cat-

converter of your truck. This can be determined by laying the cat-back system out next to or

under your truck to compare length.

ASSEMBLY

1. Clamp the intermediate pipe to the catalytic converter with the 2-1/2” U-clamp and just snug them

so you can adjust the pipe easily on the catalytic. Make sure that you have engaged the stock

rubber hanger with the wire hanger welded to the pipe.

2. Slip the muffler onto the intermediate pipe with a 3” clamp on the front. The offset of the muffler

is the (rear) outlet. Snug the clamp so you can adjust the pipes.

3. Install a 3” U-clamp hanger assembly on the front of the overaxle pipe and engage it into the

stock rubber hangers as you slip it into the muffler. Snug the clamps, remove front tailpipe rubber

insulator.

4. Slip tailpipe on overaxle pipe. Install hanger strap over 3” clamp “U” bolt. See Figure 1. Snug

clamp with hanger strap and slip hanger bolt through strap and the next rubber insulator, using

supplied fender washer and nyloc nut snug hanger bolt. Remove rubber hanger toward front of

truck. Note: This hanger can be used as an adjustment point. Adjust hanger for best clearance.

5. Working from the front of the system, align and tighten each pipe from the cat-back.

6. Check for clearance to body, frame, and driveline as you tighten the system from front to rear.

7. Check for leaks and correct if any is found.

WARNING: Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any

leaks before driving!

PostScript Picture

(Edelbrock B/W Logo.eps)

KIT CONTENTS

RPM SERIES CAT-BACK EXHAUST

CATALOG #5726

Qty.Part # Description

125-3123 Intermediate Pipe

125-5505 Muffler

123-3121 Overaxle Pipe Assembly

125-3145 Tail Pipe

146-5185 2-12/” U-clamp

346-5186 3” U-clamps

123-1754 Hanger Bar

168-8550 Hex Bolt

160-9184 Nyloc Nut

133-4500 Fender Washer

Please complete and mail your warranty card. Be sure to write the mode number in the “Part #”

space.

Thank you.

WARNING: Support your vehicle with proper

jackstands or ramps rated for the total vehicle

weight. Place stands so that the rear axle is

allowed to hang free for easy system removal.

WARNING: These cat-back systems are

engineered to fit stock catalytic converters or

equivalent replacements. If your original

system has been modified, Edelbrock will not

warranty fit or performance.

Overaxle / Tail Pipe Assembly

Intermediate Pipe Assembly

Hanger

Hanger Clamp Assembly

RPM Series Muffler #5505

Otros manuales de Pieza de automóvil de Edelbrock

Edelbrock

Edelbrock 2114 Manual de usuario

Edelbrock

Edelbrock Russell 651107 Manual de usuario

Edelbrock

Edelbrock Intake Manifolds Guía de aplicación

Edelbrock

Edelbrock 7122 Manual de usuario

Edelbrock

Edelbrock EFI Fuel Pressure Regulators 1728 Manual de usuario

Edelbrock

Edelbrock 5624 Manual de usuario

Edelbrock

Edelbrock 72700 Manual de usuario

Edelbrock

Edelbrock 2801 Manual de usuario

Edelbrock

Edelbrock 4803 Manual de usuario

Edelbrock

Edelbrock 47493 Manual de usuario

Edelbrock

Edelbrock 15008 Manual de usuario

Edelbrock

Edelbrock Edelbrock Headers 65632 Manual de usuario

Edelbrock

Edelbrock 3881 Manual de usuario

Edelbrock

Edelbrock 63-65903 Manual de usuario

Edelbrock

Edelbrock 71883 Manual de usuario

Edelbrock

Edelbrock 66642 Manual de usuario

Edelbrock

Edelbrock 5682 Manual de usuario

Edelbrock

Edelbrock 1801 Manual de usuario

Edelbrock

Edelbrock 68752 Manual de usuario

Edelbrock

Edelbrock 2263 Manual de usuario

Edelbrock

Edelbrock 2 & 4 W/D Manual de usuario

Edelbrock

Edelbrock 72282 Manual de usuario

Edelbrock

Edelbrock 541583 Manual de usuario

Edelbrock

Edelbrock Performer 70060 Manual técnico

Manuales populares de Pieza de automóvil de otras marcas

Dakota Digital

Dakota Digital 650277 Manual de usuario

bosal

bosal 037031 Manual de usuario

Vintage Air

Vintage Air 571063 Manual de usuario

GFB

GFB EX38 Manual de usuario

bosal

bosal 028091 Manual de usuario

Dodge

Dodge 8W-43 Guía de inicio rápido

ICI

ICI Magnum FBM10DGN Manual de usuario

Volant Perfomance

Volant Perfomance 19435 Manual de usuario

BENDIX

BENDIX GEN 4 GEN 5 ABS Manual de usuario

Vintage Air

Vintage Air 571065 Manual de usuario

Rugged Ridge

Rugged Ridge 11503.13 Manual de usuario

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manual de usuario

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Guía

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manual de usuario

Toshiba

Toshiba 48-1250 A Manual de usuario

aldes

aldes EHT2 Manual de usuario

Go Rhino

Go Rhino 24371T Manual de usuario

BBK

BBK 18950 Manual de usuario