Edelbrock 33503 Manual de usuario

INSTALLATION INSTRUCTIONS

FOR 1992-1995 VIPER SHOCKS

Catalog #33503

§Please read these instructions entirely before beginning. Proper installation is a must to realize the

maximum performance improvements.

IMPORTANT NOTES:

§Upon initial inspection, some new shocks may have a small amount of oil in the area of the seal. This is a

normal occurrence following manufacture and does not indicate a problem with your shocks.

§Any time you are working under a vehicle, be sure to use the proper jack stands and tire chocks to prevent

any shifting or slipping of the car. Never use a jack only to support the vehicle while changing shocks.

§Inspect shock brackets or mounting points before installation to make sure they are not broken or bent.

§Do not attempt to disassemble the Edelbrock IAS shocks. Contact your point of purchase or Edelbrock

for any necessary service or repairs.

INSTALLATION INSTRUCTIONS

Step 1 Support Viper by frame with jack stands or

on a lift.

Step 2 Remove all four wheels.

Step 3 Removal of front shocks:

Fig. 2

An aluminum block should be placed between arm and

hammer to minimize marking control arm, do not hammer

directly on the arm. It should only require a couple of

sharp taps with a hammer in order to pop from seat. Do

both left and right sides, and remove nuts.

3(a) Loosen upper and lower shock nuts, but do not

remove the bolts at this time. (See Fig. 1).

3(b) If the lower shock nut is to rear, the lower sway

bar end link must be removed in order for the

bolt to have enough clearance for removal.

(See Fig. 1).

Fig. 1

3(c) Removal of lower sway bar end link

If the tool for unseating the sway bar from the

lower control arm is not available, the following

procedure may be used. (The sway bar end

link is held in place with a tapered seat).

In order to remove:

3(c)1 Loosen lower sway bar end link nut, do

not remove the nut completely.

3(c)2 Place jack under the nut.

3(c)3 Jack up and apply pressure to the nut.

3(c)4 Tap control arm with hammer.

(See Fig. 2).

3(d) Remove upper and lower bolts to remove

shock. It may need a little gentle persuasion

with a pry bar (See Fig. 3). Bolt should come

out by hand.

Fig. 3

Step 4 Removal of rear shock Step 7 Assembly of IAS shocks

4(a) Loosen upper and lower nuts.

4(b) In order to remove bolts, they may need a little

gentle persuasion with a pry bar. Bolt should

come out by hand. (See Fig. 3).

4(c) Shock will now come out through the top.

Step 5 Disassembly of coil springs from shocks

7(a) Adjust all four threaded spring collars to 2

3/8" from the top of collar. This will return

your Viper to the stock ride height. (Note:

Apply anti-seize compound to threaded

collars). The threaded collars may be

adjusted to raise or lower the ride height.

It is recommended to wait until after the

installation to settle the suspension and

determine the final ride height changes.

(See Fig. 6).

Fig. 6

A coil spring compressor is required to remove the

springs from shocks. All proper safety precautions must

be followed. Consult the spring compressor

manufacturer's recommended instructions before

starting.

5(a) Compress the coil spring (see Fig. 4).

Fig. 4

5(b) Move bump rubber up shaft in order to remove

spring seat retainer. (See Fig. 5).

Fig. 5

5(c) Release coil spring compressor carefully.

7(b) Install and tighten allen set screw with 1/8"

allen wrench. (See Fig. 7).

Fig. 7

7(c) Slide threaded collar onto shock. It should

seat against the snap ring. Front shocks

are identified by part #33506, rear part

#34506. The part numbers are printed on

the side of the shock.

8(e) Align end of coil spring to lowest point on

spring seat before releasing the spring

compressor. (See Fig. 11).

Fig 11

Step 9 Assembly of Rear IAS shocks

9(a) Rear rod end uses the long threads. The

procedure of assembly is the same as the

front. (See Fig. 9).

Step 10 Installing IAS shocks

Reinstallation is reverse of removal.

10(a) Both front and rear may require a little gentle

persuasion with a long pry bar to push control

arms down in order to install bolts (See Fig. 12

and Fig. 12a). Shocks are mounted with the

body up & the rod end down. Do not torque

nuts at this time. Front lower bolts may be

installed with nuts to the front. This will make it

easier for reassembly.

Step 8 Assembly of Front IAS shocks

8(a) Insert the coil spring with flat ground end

against the threaded collar spring seat.

8(b) Compress coil spring until lower seat has

enough clearance to install lower spring seat

and 9/16" jamb nut (See Fig. 8).

Fig. 8

8(c) Front rod end has short threads.

(See Fig. 9).

Rear lower rod end Front lower rod end

Fig. 9

8(d) Screw rod end on with the supplied Loctite

applied, torque nut to 75 ft. lbs.

(See Fig. 10).

Fig. 10

Fig. 12

Fig. 12a

10(b) Front sway bar end links may now be reinstalled. Install both left and right at the same time. After both

sides are in position, the end link to control arm nuts can now be torqued to 16 ft. lbs.

10(c) Important: After all four shocks are installed, place jack or jack stand under control arm to support

vehicle and load suspension at ride height. Torque the shock mounting bolts to 80-100 ft. lbs.

This must be done to pre-load the bushing in their proper position for safe and proper handling. This is a

very important step.

10(d) Install and torque wheels to 90 ft. lbs. After 5-10 miles, re-torque wheels to 90 ft. lbs.

Parts List

Qty. Description Qty. Description

2 #33506 Front shock assemblies 4 Upper coilover spring perch

2 #34506 Rear shock assemblies 1 Loctite tube

4 Lower spring seats 1 Anti-seize

2 Front lower rod ends (short threads)

2 Rear lower rod ends (long threads) 1 Hardware kit

4 -set screws

4 -9/16 jam nuts

4 Coil over threaded sleeves

Enjoy the improved ride and handling from your new Edelbrock IAS shocks.

Edelbrock Corporation

2700 California Street

Torrance, California 90503

Toll-Free Tech Line (800) 416-8628

Tech Fax (310) 972-2730

Tech E-mail: [email protected]

P/N 84-8151

2001 Edelbrock Corporation Revised 2/01

Tabla de contenidos

Otros manuales de Pieza de automóvil de Edelbrock

Edelbrock

Edelbrock 5787 Manual de usuario

Edelbrock

Edelbrock 47480 Manual de usuario

Edelbrock

Edelbrock 70028 Manual de usuario

Edelbrock

Edelbrock 5419 Manual de usuario

Edelbrock

Edelbrock 5772 Manual de usuario

Edelbrock

Edelbrock 5671 Manual de usuario

Edelbrock

Edelbrock 6661 Manual de usuario

Edelbrock

Edelbrock Victor X 4760 Manual de usuario

Edelbrock

Edelbrock 15015 Manual de usuario

Edelbrock

Edelbrock 65812 Manual de usuario

Edelbrock

Edelbrock 15016 Manual de usuario

Edelbrock

Edelbrock 5672 Manual de usuario

Edelbrock

Edelbrock 460 Ford Manual de usuario

Edelbrock

Edelbrock 5645 Manual de usuario

Edelbrock

Edelbrock 5061 Manual de usuario

Edelbrock

Edelbrock 66092 Manual de usuario

Edelbrock

Edelbrock 2166 Manual de usuario

Edelbrock

Edelbrock 71001 Manual de usuario

Edelbrock

Edelbrock 3871 Manual de usuario

Edelbrock

Edelbrock 47493 Manual de usuario

Edelbrock

Edelbrock Edelbrock Header 6525 Manual de usuario

Edelbrock

Edelbrock 65932 Manual de usuario

Edelbrock

Edelbrock 2980 Manual de usuario

Edelbrock

Edelbrock Performer 4754 Manual de usuario

Manuales populares de Pieza de automóvil de otras marcas

Dakota Digital

Dakota Digital 650277 Manual de usuario

bosal

bosal 037031 Manual de usuario

Vintage Air

Vintage Air 571063 Manual de usuario

GFB

GFB EX38 Manual de usuario

bosal

bosal 028091 Manual de usuario

Dodge

Dodge 8W-43 Guía de inicio rápido

ICI

ICI Magnum FBM10DGN Manual de usuario

Volant Perfomance

Volant Perfomance 19435 Manual de usuario

BENDIX

BENDIX GEN 4 GEN 5 ABS Manual de usuario

Vintage Air

Vintage Air 571065 Manual de usuario

Rugged Ridge

Rugged Ridge 11503.13 Manual de usuario

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manual de usuario

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Guía

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manual de usuario

Toshiba

Toshiba 48-1250 A Manual de usuario

aldes

aldes EHT2 Manual de usuario

Go Rhino

Go Rhino 24371T Manual de usuario

BBK

BBK 18950 Manual de usuario