ECS P5SD-B Plus Manual de usuario

Important Information

This publication, including all photographs, illustrations and software, is protected

any of the material contained herein, may be reproduced without the express written

consent of the manufacturer.

Disclaimer

The information in this document is subject to change without notice. The

manufacturer makes no representations or warranties with respect to the contents

hereof and specifically disclaims any implied warranties of merchantability or fitness

for any particular purpose. Further, the manufacturer reserves the right to revise this

publication and to make changes from time to time in the content hereof without

obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II are a registered trademarks of Intel Corporation.

VGA, OS/2, PS/2 are registered trademarks of International Business Machines.

AMD, K5 are registered trademarks of Advanced Micro Devices Inc.

Cyrix, M1 are registered trademarks of Cyrix Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Version 1.3

Safety Compliance

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

♦Reorient or relocate the receiving antenna.

♦Increase the separation between the equipment and the receiver.

♦Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

♦Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and shielded AC power cable must be employed with this

equipment to insure compliance with the pertinent RF emission limits governing this

device. Changes or modifications not expressly approved by the system’s

manufacturer could void the user’s authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the

following conditions:

♦This device may not cause harmful interference, and

♦This device must accept any interference received, including interference that

may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur

le matériel brouilieur du Canada.

Chapter 1: Introduction

Welcome.... ......... ......... ......... ........ ......... ......... .........1

About the Manual . ......... ......... ........ ......... ......... .........1

Checklist..... ......... ......... ......... ........ ......... ......... .........2

Features..... ......... ......... ......... ........ ......... ......... .........2

Chapter 2: Installation

Before You Begin . ......... ......... ........ ......... ......... .........4

Mainboard Guide.. ......... ......... ........ ......... ......... .........5

Preparing the Mainboard ......... ........ ......... ......... .........6

Install the Mainboard in the System Case .... ......... .........10

Chapter 3: Setup

About the Setup Utility .... ......... ........ ......... ......... .........13

Standard CMOS Setup Option.. ........ ......... ......... .........15

BIOS Feature Setup Option...... ........ ......... ......... .........16

Chipset Features Option. ......... ........ ......... ......... .........18

Power Management Setup Option ..... ......... ......... .........19

PNP/PCI Configuration Option.. ........ ......... ......... .........22

Load BIOS Defaults Option....... ........ ......... ......... .........23

Load Setup Defaults Option...... ........ ......... ......... .........23

Integrated Peripherals Option ... ........ ......... ......... .........23

Password Settings ......... ......... ........ ......... ......... .........25

IDE HDD Auto Detection Option ........ ......... ......... .........25

Save and Exit Setup Option...... ........ ......... ......... .........26

Exit Without Saving Option ....... ........ ......... ......... .........26

Chapter 4: Software

About the Software......... ......... ........ ......... ......... .........27

Quick Jumper Setting Reference

Quick Jumper Setting Reference ....... ......... ......... .........30

Welcome

Congratulations on your purchase of the P5SD-B+ mainboard. The P5SD-B+

mainboard is the latest generation of socket-7 motherboards with support for an

accelerated graphics port AGP, a high-speed system bus, and onboard PCI IDE

channels with UltraDMA-33 extensions. As a socket–7 board, the P5SD-B+ supports a

wide range of Pentium MMX processors, the Pentium-compatible AMD K5/K6 series,

the Cyrix/IBM 6X86, and the IDT C6 series CPUs. Five expansion slots are available

for add-in cards as well as the AGP slot for a graphics adapter. The mainboard has

dual power connectors and can run using an ATX or an AT power supply. In short, the

P5SD-B+ mainboard delivers powerful entry-level performance and supports a wide

range of inexpensive components.

This chapter contains the following information:

lAbout the Manual explains how the information in this manual is

organized

lChecklist comprises a list of the standard and optional components that are

shipped with this mainboard,

lFeatures highlights the functions and components that make this one of

the best value mainboards on the market

About the Manual

The manual consists of the following chapters:

Introduction

Use the Introduction Chapter to learn about the features of the mainboard, and the

checklist of items that are shipped with the package.

Installation

Use the Installation Chapter to learn how to install the mainboard and get your system

up and running.

Setup

Use the Setup Chapter to configure the mainboard for optimum performance.

Software

Use the Software Chapter to learn how to use the software drivers and support

programs that are provided with this mainboard.

Checklist

Compare the contents of your mainboard package with the standard checklist below. If

any item is missing or appears damaged, please contact the vendor of your mainboard

package.

Standard Items

1 x P5SD-B+ Mainboard

1 x Cable/Bracket Pack

Diskette drive ribbon cable

IDE drive ribbon cable

This User’s Manual

Software Support Disks

Features

The main feature of the P5SD-B+ mainboard is that it provides a cost effective socket-

7 board that supports a wide range of inexpensive processors. However, it upgrades

the socket-7 format with a 100 MHz system bus and support for AGP graphics

adapters.

Low-cost Processing

The socket-7 processor socket supports a wide range of low-cost Pentium and

Pentium-compatible processors from a variety of vendors. You can install the board

with an Intel Pentium or Pentium MMX, an AMD K5 or K6, a Cyrix/IBM 6X86, or an

IDT C6. The board will support CPU clocks from 90 MHz through to over 300 MHz,

and CPU voltages of 2.1 up to 3.5 volts. All the supported processors have internal

level-1 cache memory and the mainboard is installed with 512K of PBSRAM level-2

external cache memory.

Versatile Memory Support

The board has two SIMM sockets for older 72-pin EDO or FP DRAM modules, and

two DIMM sockets for newer 168-pin SDRAM modules. The SIMM sockets allow

memory from older machines to be recycled into a modern, performance, socket-7

system.

AGP Graphics Support

The mainboard has an AGP slot for the optional installation of an accelerated graphics

port video adapter. AGP is today’s standard for high-performance 2D and 3D video

processing

Versatile Expansion Options

The board has 6 expansion slots. Four PCI slots can be used by 32-bit PCI expansion

cards. Two ISA slots can be used by 8-bit/16-bit ISA expansion cards. One PCI slot is

shared with one of the ISA slots. This means that you can use either of the slots, but

not both. Five free slots, plus an AGP slot for a graphics adapter, allows a high degree

of system expansion.

Integrated I/O

The board features a full set of standard I/O ports. An AT enhanced keyboard DIN

socket is pre-installed and connectors are available for one parallel, two serial, two

USB, PS/2 mouse, and infrared ports. The mainboard is installed with two PCI IDE

channels which can support Ultra-DMA-33 disk drives, and a floppy disk drive

interface.

Programmable Firmware

The mainboard includes Award BIOS which allows BIOS setting of CPU parameters.

The fully programmable firmware enhances the system features and allows users to set

power management, hardware monitoring, (optional) LAN and modem wake up,

alarms, and so on.

Before You Begin

Before you begin to install your P5SD-B+ mainboard, take some precautions to ensure

that you avoid the possibility of damage to the product from static electricity.

Ensure too that you are installing the mainboard into a suitable case.

Static Electricity

In adverse conditions, static electricity can accumulate and discharge through the

integrated circuits and silicon chips on this product. These circuits and chips are

sensitive and can be permanently damaged by static discharge.

♦If possible wear a grounding wrist strap clipped to a safely grounded device

during the installation.

♦If you don’t have a wrist strap, discharge any static by touching the metal case

of a safely grounded device before beginning the installation.

♦Leave all components inside their static-proof bags until they are required for

the installation procedure.

♦Handle all circuit boards and electronic components carefully. Hold boards by

the edges only. Do not flex or stress circuit boards.

Choosing a Case

The P5SD-B+ mainboard has a power connector for an AT or an ATX power supply.

The size of the board is small enough for a micro-ATX format case.

Some features on the mainboard are implemented by cabling connectors on the

mainboard to indicators and switches on the system case. Ensure that your case

supports all the features required.

The P5SD-B+ mainboard can support one or two floppy diskette drives and four

enhanced IDE drives. Ensure that your case has sufficient power and space for all the

drives that you intend to install.

The mainboard has a single AT-keyboard port on the rear edge. All other ports use

cables to connect to the case ports. In addition the mainboard supports 6 expansion

slots (two shared). Make sure that your case supports all the I/O ports and expansion

slots that you intend using.

Mainboard Guide

Use the following illustration and key to identify the components on your mainboard.

JP2

JP101

COM2

JP100

COM1

SIM1

SIM2

DIMM1

DIMM2

JP9

JP6

JP7

JP8

JCH1

JV_L1

SOCKET-7

JP1

JPW1

F_PNL1

JP12

JP11

JP10

FAN1

FAN2

JVBAT1

SL1

SL2

PCI1

PCI2

PCI3

PCI4

JIR1

AGP

IDE1

IDE2

JUSB1

LPT1

FDD1

JP5

CN6

CN5

JP13

Key to Components

Component Description

SL1, SL2 2 x 8/16-bit ISA expansion slots

PCI 1,2,3,4 4 x 32-bit PCI expansion slots

AGP Slot for AGP graphics adapter

Socket-7 Processor socket

SIM1, SIM2 Slots for 72-pin memory module

DIMM1, DIMM2 Slots for 168-pin memory module

FDD1 Connector for floppy disk drives

IDE1, IDE2 Primary and secondary IDE channels

COM1, COM2 Connectors for serial ports 1 & 2

LPT1 Connector for parallel port

JP2 AT-keyboard socket

JUSB1 Connector for USB ports

CN6 Connector for AT power supply

Component Description

CN5 Connector for ATX power supply

JIR1 Connector for infrared port

JP100 Modem wake up connector

JP101 LAN wake up connector

JP5 Connector for PS/2 mouse

FAN1 Power connector for CPU cooling fan

FAN2 Power connector for system cooling fan

JP 6,7,8 Speed setting for system bus, PCI bus, AGP bus jumpers

JP9 Clock setting for memory jumper

JP10 Clock setting for memory jumper

JP 11, 12 Clock setting for AGP and PCI jumpers

JPW1 Processor core voltage setting jumper

JP1 System bus multiplier for CPU clock jumper

JCH1 Burst mode select jumper

JV_L1 Single or dual voltage CPU select jumper

JVBAT1 Clear CMOS memory jumper

F_PNL1 Panel Connector

JP13 Set CPU I/O Voltage jumper

A Note on Jumpers

A jumper consists of two or more pins mounted on the mainboard. Some

jumpers might be arranged in a series with each pair of pins numbered

differently. Jumpers are used to change the electronic circuits on the

mainboard. When a jumper cap is placed on two jumper pins, the pins are

SHORT. If the jumper cap is removed (or placed on just a single pin) the pins

are OPEN.

Preparing the Mainboard

Prepare the main board by installing the Pentium or Pentium-compatible processor and

then installing memory modules. This board supports processors that run from

90MHz through to over 300 Mhz. Finally, review all the important jumper settings to

ensure that the board is configured correctly.

Install the Processor

1. Locate the zero insertion force (ZIF) socket-7 for the processor. On the socket

and on the processor, identify the pin 1 corner. You can identify the pin 1 corner

by noting that in the rectangular matrix of pins and holes on the socket and

processor, one pin and one hole is absent on the pin 1 corner.

2. Push the socket locking lever away from the socket to unhook it. Swing the lever

into the upright position.

3. Insert the processor into the socket taking care that you have matched the pin 1

corners. No force is required, and the processor should seat smoothly into the

socket.

4. Swing the locking lever down and hook it under the latch on the side of the socket

to lock it in place.

5. If your processor includes a built-in cooling fan, connect the cable from the

cooling fan to the CPU cooling fan connector on the mainboard FAN1.

Install the Memory Modules

On this mainboard, you can use 168-pin Dual In-line Memory Modules (DIMMs) or

72-pin Single In-Line Memory Modules (SIMMs). Two sockets are available for each

kind of memory. The memory modules can be installed with Fast Page-mode RAM

(FP), EDO RAM or SDRAM.

For maximum performance, you should use SDRAM DIMM modules which are PC-

100 compliant, i.e. they will run up to 66MHz external clock not including 66MHz.

However, you can reduce cost by using older FP or EDO SIMMs or DIMMs. You

may have to configure your board for a slower system/memory bus in order to use

slower kinds of memory.

The DIMMs can hold memory capacities from 8 MB through to 256 MB. The SIMMs

are usually installed with a maximum of 64 MB. You can install two SIMM

modules(SIMM1+SIMM2=BANK0), or one or two DIMM modules

(DIMM1=BANK1, DIMM2=BANK2). You cannot install a combination of SIMMs

and DIMMs. The memory modules must be installed with the same kind of RAM.

You cannot install one module using SDRAM, and another module using EDO RAM.

Installing DIMMs

1. The DIMM sockets are keyed with notches and the DIMMs are keyed with cut-

outs so that they can only be installed correctly. Check that the cut-outs on the

DIMM edge connector matches the notches in the SDRAM socket.

2. Push the latches on each side of the SDRAM socket down.

3. Install the DIMM into the socket and press it carefully but firmly down so that it

seats correctly. The latches at either side of the socket will be levered upwards

and latch on the edges of the DIMM when it is installed correctly.

Installing SIMMs

1. Hold the SIMM over the SIMM socket. Hold the SIMM at an angle so that you

can insert the edge connector side of the module into the socket.

2. When the edge connector side is fully inserted in to the socket, swing the SIMM

into a vertical position. The latches at either side of the SIMM socket will snap

onto the SIMM and hold it firmly in place.

Check all the Jumper Settings

Check all the mainboard jumpers to ensure that the board is configured correctly

according to the speed and timing of your processor, the VGA sub-system you are

using, and so on. Regarding the CPU settings please refer to the ‘Quick Jumper

Setting Reference’on page 31.

Tabla de contenidos

Otros manuales de Placa madre de ECS

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario