EcoxGear SoundExtreme Manual de usuario

SoundExtreme

Models: GDI-EXSNDXTR00...20

POWERSPORTS

AMPLIFIED

SOUNDBAR

User Guide

SoundExtreme Layout

FRONT

BACK

Auxiliary Power Out

SAE Connector (Black)

Control PanelBacklit Speakers

Backlit Woofer

RIGHT SIDELEFT SIDE

Backlit Woofer

12V Power In SAE

Connector (Red) Light Bar

In/Out Connections

Do NOT use these connections if they are wet.

AUX-IN: This input can be used to connect a CD player, MP3 player, etc.

AUX-OUT: This output can be used to connect to an amplifier or to

another speaker AUX-IN connection.

USB Charging Port: Connect your device’s charge cable here to charge it.

USB charging only functions when the SoundExtreme’s power is turned

on. USB port rating is 5V, 2.1A.

Important: Maintaining Waterproofness

If the caps on the control panel, the AUX-IN, and AUX-OUT Ports are not

properly closed, the unit is NOT watertight.

To close properly, push firmly to be sure the cap fits flat along the edges

with the panel.

BOTTOM

AUX-OUT

Port

AUX-IN

Port

USB Charging

Port

Connecting to 12VDC

Power Supply

Attach the 6ft Power Cable to the 12V Power In SAE Connector (RED).

Use Caution: Do NOT connect to 12V Battery if the Power In SAE

Connector is wet. Contact may cause electric shock and injury if wet.

The SoundExtreme does not have an internal battery. It must be

connected to an external 12VDC power supply to function. When you install

the SoundExtreme to a battery or a voltage regulator on a golf cart, a boat,

a quad bike, a UTV, or another vehicle, you need to make sure that your

vehicle battery or battery pack terminal voltage is 12VDC. If the battery

terminal voltage is not 12V, you will need a DC–DC converter with output

12V. Connecting the SoundExtreme to a non-12VDC power source will lead

to a malfunction or damage to the speaker.

WARNING: Even when powered off, the SoundExtreme will draw a small

amount of power from your battery. To prevent draining your battery when

your SoundExtreme or powersports vehicle are not in use for more than

48hrs, we suggest unplugging the SoundExtreme from the battery or

adding toggle switch. (Toggle switch sold separately.)

Remove the 15 Amp Blade Fuse from the Fuse Holder.

Use Caution: Do NOT remove Fuse if the Fuse Holder is wet. An improperly

fitted cap may cause electric shock and injury if wet.

To close properly, push firmly to be sure the cap snaps into place.

Black Cable Red Cable

Loosen Bolts

Tighten Bolts

Installation: Gas Vehicle

1. Loosen the bolts on the

battery terminals.

Use Caution: Do NOT attempt to loosen

bolts if battery is wet. Contact may

cause electric shock and injury if wet.

2. Connect the BLACK wire to the

BLACK, negative terminal, then

the RED wire to the RED, positive

terminal. Unit will not work correctly

and may be damaged if wires are not

correctly attached.

3. Tighten the bolts on the battery

terminals until the connectors are

held firmly in place.

4. Return the 15 Amp Blade Fuse into

the Fuse Holder and close the cap.

Installation: Electric Vehicle

1. Switch your vehicle to TOW mode.

2. Loosen the bolts on the

battery terminals.

3. Connect the BLACK wire to the

GROUND on the DC-DC Converter,

then the RED wire to the POSITIVE

(+) post on the DC-DC Converter.

Unit will not work correctly and

may be damaged if wires are not

correctly attached.

4. Tighten the bolts on the battery

terminals until the connectors are

held firmly in place.

5. Return the 15 Amp Blade Fuse into

the Fuse Holder and close the cap.

Tip: Use zip ties to gather any excess

wires, and secure them so that they are

not dangling, loosely.

Controls

1. LED Indicators: Each of the 4 LEDs

correspond to different functions:

Power, Bluetooth, Mode, and Status.

2. Power Button: Press button to

turn the SoundExtreme on / off.

3. Mode Button: Press button to

cycle through the following modes:

Bluetooth, EcoCast Transmitting,

EcoCast Receiving, FM, and AUX-IN.

4. Volume Control Buttons: Press

to adjust the speaker’s volume.

Press and hold to adjust the

volume continually.

5. Track Buttons: Press buttons to

go to the previous / next track on

a paired Bluetooth device.

6. Backlight Speakers Button: Press to cycle through the following 4

Party Light Modes: Green Light, Red Light, Music Sync, and Fading.

7. Light Bar Button: Press to cycle through the following 4 Light Modes:

Red Light, White Light (High), White Light (Mid), and White Light (Low).

Press and hold to enable / disable Accessory Mode (which turns on/

off the Auxiliary Power Out connection).

8. Bluetooth Button: When in Bluetooth Mode, if the Bluetooth LED

Indicator is not flashing Blue, press this button to enter Bluetooth

Pairing mode. If your device is paired (solid Blue LED), press button to

disconnect. Press and hold this button for 5 seconds to clear all pairing

records. In FM Mode, this button is used for FM Station Preset 1.

9. Play / Pause / Answer / EcoTalk Button: Press to play / pause a

track or answer / end a mobile call from a paired Bluetooth device.

Press and hold to activate your Voice Assistant (Siri and OK Google). In

FM Mode, this button is used for FM Station Preset 2.

6 7

CONTROL PANEL

Operations

LED Indicators

From left to right, the 4 LED Indicators correspond to Power, Bluetooth,

Mode, and Status.

1. Power

Solid Green: Power On

No Light: Power Off

2. Bluetooth

Flashing Blue: Bluetooth Paring

Solid Blue: Bluetooth Connected

3. Mode

Solid Blue: Speaker Mode

Solid / Flashing Red: EcoCast Transmitting Mode

Solid / Flashing Green: EcoCast Receiving Mode

4. Status

Solid Blue: FM

Solid Green: AUX-IN

Solid Red: Accessory Mode Enabled

Power On/Off

Power On: Press briefly to power on the SoundExtreme. “Speaker on,

ready to connect” voice prompt will be heard.

Power Off: Press briefly to power off the SoundExtreme.

Mode Button

Press briefly to cycle through the following modes: Bluetooth,

EcoCast Transmitting, EcoCast Receiving, FM, and AUX-IN.

Pairing a Bluetooth Device

1. Turn on your Bluetooth device.

2. Power on SoundExtreme. “Speaker on, ready to connect” voice

prompt will be heard. If the Bluetooth LED Indicator (the second

LED Indicator from the left) is not flashing, briefly press to

start pairing your device.

3. Navigate to your Bluetooth device’s setup screen, find

ECOXGEAR and connect. If the connection is successful, the

Bluetooth icon will be lit solid and your SoundExtreme will

announce “Your phone is connected.”

Notes:

· If the pairing is not complete within 5 minutes, the speaker will

exit the pairing mode. You need to repeat the pairing steps again.

· After the connection is successful, if you turn the speaker off

and turn it on again, it will reconnect to the last connected

device automatically. Also, a voice prompt, “Speaker on, ready to

connect” followed by, “Your phone is connected” will be heard.

· PRESS AND HOLD for 5 seconds to clear all pairing records.

Adjust Volume

1. Press or briefly to adjust the speaker volume.

2. PRESS AND HOLD or to adjust the volume continuously.

a. Press briefly to increase one volume level. PRESS

AND HOLD to keep increasing the volume until

maximum volume level is reached.

b. Press briefly to decrease one volume level. PRESS

AND HOLD to keep decreasing the volume until

minimum volume level is reached.

Play Music (Bluetooth Mode)

After the SoundExtreme is connected to your Bluetooth device,

press briefly on the SoundExtreme to play, press again

to pause.

Press briefly to play previous song. Press briefly to get the

next song.

Notes:

· Pair and connect your Bluetooth device with SoundExtreme

before using this feature.

· If a call is received when you are listening to music, press briefly

on the SoundExtreme to answer the call. Press again to end

the call.

· You can also control Volume and Play / Pause music operations

from your Bluetooth enabled device. When the Audio Source is

via the AUX-In connection, you must use your device to control

Play / Pause music operations.

EcoTalk

PRESS AND HOLD for 3 seconds to activate the voice assistant on

your device (Siri, OK Google, etc.). Once activated, the speakerphone mic

on your SoundExtreme will hear your voice commands and transfer them

to the voice assistant on your device.

Notes:

· Before using the EcoTalk function, your device must be connected to

the SoundExtreme via Bluetooth.

· Not all devices have voice assistant functionality; refer to your device

for details.

x50

EcoCast – Broadcast Your Music

to Multiple Speakers

1. Follow the Pairing a Bluetooth Device instructions to connect one

SoundExtreme (Speaker A) to your Bluetooth device. After your device

is connected to Speaker A, you can select a song to play.

2. Press on Speaker A to initiate EcoCast Transmitting Mode. The

Mode LED Indicator (the third LED Indicator from the left) will flash

Red, and the speaker will announce, “EcoCast transmitting.”

3. Power on Speaker B speaker and press to cycle through to and

initiate EcoCast Receiving Mode. The Mode LED Indicator will flash

Green, and the speaker will announce, “EcoCast receiving.”

4. Once the connection between the speakers is successful, Speaker B

will announce, “Connection Successful,” and start playing music from

your Bluetooth device.

When you have two or more SoundExtreme speakers, you can build

a broadcast system by initiating EcoCast Transmitting Mode in one

SoundExtreme speaker and broadcasting your music to one or more

SoundExtreme speakers in EcoCast Receiving Mode.

EcoCast: First Two Speakers

A B

Otros manuales para SoundExtreme

Tabla de contenidos

Otros manuales de Sistema de altavoces de EcoxGear

EcoxGear

EcoxGear SoundExtreme SEDS32 GDI-EXSEDS3200 20 Series Manual de usuario

EcoxGear

EcoxGear SoundExtreme Manual de usuario

EcoxGear

EcoxGear SoundExtreme SEDS32 Manual de usuario

EcoxGear

EcoxGear SoundExtreme SE18 GDI-EXSE1800 20 Series Manual de usuario

EcoxGear

EcoxGear SoundExtreme Elite SE28 Manual de usuario

EcoxGear

EcoxGear GDI-EXSE1800 20 Series Manual de usuario

EcoxGear

EcoxGear SoundExtreme SE26 Manual de usuario

Manuales populares de Sistema de altavoces de otras marcas

JVC

JVC CA-MXK5R Manual de usuario

LG NB4532B Manual de usuario

JVC

JVC CA-FSH100 Manual de usuario

5Core

5Core Pro Series Manual de usuario

EAW

EAW MQV1394e Manual de usuario

Lynx

Lynx GXR-LA10A Manual de usuario

iLive

iLive ITB066B Manual de usuario

RDX

RDX QuickStation 4 Manual de usuario

Electro-Voice

Electro-Voice S-122 Manual de usuario

Sven

Sven SPS-619 GOLD Manual de usuario

Pioneer

Pioneer CS-7070 Manual de usuario

EAW

EAW UB82e Manual de usuario

Sondpex

Sondpex Active Speaker System and Digital Music... Manual de usuario

JVC

JVC NX-PN7 Manual de usuario

Marshall Amplification

Marshall Amplification AR-DM61-BT Manual de usuario

Yamaha

Yamaha NX-A01 - Speaker Sys Manual de usuario

SE Audiotechnik

SE Audiotechnik I-LINE Manual de usuario

Gemini

Gemini WRX-843 Series Manual de usuario