ecopoint OptaLine ELG300B10W840 Hoja de instrucciones
IMPORTANT:
OptaLine - Low Glare Prole Luminaire
| Product Instructions
Mass:
0.90 kg (300 mm)
1.65 kg (600 mm)
3.10 kg (1200 mm)
305 / 605 / 1205 mm
60 mm
DIMENSIONS:
FOR YOUR SAFETY AND THE LONG-TERM RELIABILTY OF THIS PRODUCT, READ AND
FOLLOW ALL INSTRUCTIONS TO PREVENT HARM TO THE LUMINAIRE, INSTALLER OR
PROPERTY.
Installation requires knowledge of electrical and luminaire systems; installa-
tion must only be completed by a licenced or suitably qualied electrician.
Disconnect power before installation.
Do not alter pre-existing holes or drill new holes unless instructed to do so
according to this manual.
Do not expose wiring to sharp objects or edges of sheet metal, always check
clearances prior to any drilling and de-burr edges.
No components of this luminaire are serviceable by the user, and there is
danger of personal and/or property harm if the luminaire is modied or dis-
assembled.
If any luminaire components are damaged, they shall be exclusively replaced
by the manufacturer or approved agent.
88 mm
Power Factor ≥ 0.90 (230V)
Electrical Input 220-240 V / 50-60 Hz
Operating Temperatures - 10 to +40 deg. C
Construction Extruded aluminium, PC lens
Ingress Protection IP20
Impact Protection -
Warranty 5 years
STANDARD SPECIFICATIONS
STANDARD MODELS
Product Code Size Power Nominal Flux
ELG300B10W840 305 x 60 x 88 mm 10 W 700 lm
ELG600B20W840 605 x 60 x 88 mm 20 W 1,550 lm
ELG1200B38W840 1205 x 60 x 88 mm 38 W 3,200 lm
INSTALLATION NOTES:
The following notes must be considered prior to installation of the product:
The luminaire has been designed to operate in accordance with the speci-
cations listed above; please especially note the electrical input, operating
temperature and ingress/impact protection specications and ensure that
the luminaire will only be operated within a suitable environment.
The luminaire must be securely xed to a suitable surface or structure which
is able to bear the luminaire weight and provide the necessary restraint un-
der seismic loading according to NZS 4219.
The luminaire must be installed such that adequate space is available for
ventilation to prevent overheating.
Exposure to UV (i.e. direct sunlight) over an extended period may cause dis-
colouration of the diuser and/or luminaire body.
The luminaire is not suitable for marine environments nor for hazardous
environments.
Ensure power is turned o and remove luminaire from packaging.
Accurately mark and screw hole.
Screw the housing on the ceiling
tightly and insert the light module
into the housing.
Screw the mounting nut onto the
ceiling tightly. Fix the suspension
rope through the mounting nut and
adjust height (before hanging xture).
Put the end caps and secure them
with the screws. Connect power to
mains supply and test the luminaire
for correct operation and switching.
Install the xture to the suspending
rope by screwing to security nuts of
the suspension rope. Connect power
to mains supply and test the luminaire
for correct operation and switching.
*Continuous Run installation
SUSPENDED
INSTALLATION
SURFACE MOUNTED
INSTALLATION
Open hole
Electric
drill
Press button below and pull rope
to adjust height. Cut excess
Screws
5. Plug terminals into
the same colour and put
the xtures together.
6. Screw the connect
plate into the second
xture.
Plastic
Expansion
Screws
Plastic
hammer
216 / 516 / 1116 cm
Screw
Connect
Plate
3. Push the housing of
the second xture to
the connect plate.
4. Insert light module
into the housing.
Screw
Mounting Nut
Security
Nut
Housing
AC Input
Wire
3. Push the connect
plate on the rst
xture and tighten.
4. Push the housing
of the second xture
to the connect plate.
End Cap
End Cap
1. Install the second light as the previous steps.
2. Loosen the screw and take down the End Cap
to take out the reserved embedded terminal.
5. Plug terminals into
the same colour and put
the xtures together.
6. Screw the connect
plate into the second
xture.
1. Push the connect plate on the rst
xture and tighten.
2. Insert light module into the housing.
Connect
Plate
WARRANTY COVER: CONTACT:
Ecopoint Limited guarantees this luminaire
to be free from failures resulting from
faulty materials or workmanship for a
period of 3 years (PMMA) /5 years (PC)
from the date of invoice. Retain the invoice
as proof of purchase in the event of a
warranty claim.
Failure resulting from misuse, accident,
neglect or improper operation,
maintenance, installation, modication or
adjustment are not covered by this
warranty.
Ecopoint Limited must be notied within
30 days of the alleged defect being rst
identied.
Please refer to standard Warranty Terms
and Terms and Conditions of Sale for full
detail; these are available at
www.ecopoint.co.nz
For any service or support enquiries,
please call Ecopoint head oce during
normal business hours (Monday to Friday)
or contact us via any of the means listed
below.
Ecopoint Limited
2 Jarden Mile, Ngauranga, Wellington 6035
PO Box 12646, Thorndon, Wellington 6144
P: +64 4 499 3636 or
0800 695 949
E: info@ecopoint.co.nz
W: www.ecopoint.co.nz
Ref: ELG Installation Instruction (20200723)
MAINTENANCE:
To avoid risk of harm to the luminaire or maintenance personnel, always en-
sure that the luminaire is switched o and cooled down prior to undertaking
any maintenance activities.
If maintenance tasks involve exposing any electrical components, ensure
that mains power is disconnected prior to any works.
This product should only be cleaned with a damp cloth; do NOT use any
chemical cleaning agents and/or solvents.
If dust accumulates on the inside of the diuser, simply slide the end-caps of
the luminaire body o, slide the diuser out, wipe down with a damp cloth
and allow to dry before reversing the process. CARE MUST BE TAKEN TO NOT
TOUCH ANY LEDS AND NOT ALLOW ANY MOISTURE TO COME IN CONTACT
WITH THE LEDS.
REMINDER: No components of this luminaire are serviceable by the user,;
damaged components may only replaced or repaired by the manufacturer or
approved agent.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
