Eco-Systems ECO-4094 Manual
© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
20’
20’
ECO-4094 - 20’ x 20’ Display
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Grid View
© 2022
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2022
Order #XXXXX
Using Your Setup Instructions
Cleaning and Packing Your Display
The Euro LT Hybrids Setup Instructions are created specifically for your configuration.
They are laid out sequentially in levels, including exploded views, and a logical series of detailed steps
to assemble the main structure and components. We encourage you to study the instructions before
attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your exhibit to prevent loss of the
locks and setscrews (see below in RED). This is VERY IMPORTANT.
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) When cleaning laminate inserts, countertops, or panels use mild cleansers and a soft material
such as cotton.
3) Keep all display components away from extreme heat and long exposure to sunlight to avoid
warping and fading.
4) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Each component has 2 clips,
the lower clip is ALWAYS
black. The top clip is color
coded to distinguish which
level. The color coded clip
also contains the numbered
label.
Connector
Level 1 = Blue
Level 2 = Red
Level 3 = Green
Level 4 = Black
Panel Lock
When Required
Color Coded Clip
w/ assembly number
Black Clip
is bottom of
panel
L
e
f
t
P
a
n
e
l
R
i
g
h
t
P
a
n
e
l
Cut Away View of
Slide Clips
Components connect together
by aligning them and sliding
downward connecting clips
together.
Configurations are assembled
from left to right, usually
starting with #1 and following
the numbered sequence.
Example of Connection Top View of Panels with Locks
The first level of components contain
panel locks that are located at the top of
the panel for extra stability and seamless
connection. When disassembling panels
twist top connection slightly and lift right
panel upward.
Panel Lock
When Required
Color Coded Clip
w/ assembly number
is top of panel
Left Hand
Grasps Panel
Firmly
With Right Hand Thumb
Close to Seam
Squeeze,
Push Forward,
And Lift
General Setup Instructions for Extrusion System
The Tool Typical Connection Typical Connection (cont’d) Numbered Label
Most exhibits can be assembled
with the supplied Hex Key Tool.
Occasionally, a flat head screw-
driver may be required.
Most horizontal extrusion connections have a patented expandable
lock. This lock inserts into the groove of an opposing extrusion.
Tightening the lock with the Hex Key Tool expands the lock and
creates a strong positive connection.
Each extrusion contains a numbered
label which corresponds with setup
instructions. The label is located
within a groove of the extrusion
(when possible). With extrusion
components the labels contain
Black numbers unless otherwise
specified.
Detail A Detail B Detail C
Horizontal Inline Connection (remove only one setscrew) Base Plate Connection Vertical Connection
(remove only two setscrews)
Detail D Detail E
Setscrews
Remove only (1) setscrew when disassembling.
Replace setscrew in extrusion after assembling
it. Before packing, replace setscrew in extrusion
to avoid losing it.
Attach base plate to round or
square vertical extrusion using
the bolt provided. Be careful
not to strip the threads.
When vertical extrusions are
packed in portable cases rather
than crates or tubs, they must be
broken down into smaller sections
which then require assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews
in extrusion after assembling it.
Before packing, replace setscrews
in extrusion to avoid losing them.
EuroLT Assembly
© 2022
Order #XXXXX
1) Slide TWO-PIECE TS RV 2 L-bracket into
Interior Center Slot of extrusion so that two
set screws are inside groove.
Tighten two set screws to secure.
2) Slide two A1 L-Brackets into outer interior
grooves of upper and lower horizontals.
Tighten set screws to secure.
4) Slide exposed ends of installed brackets of
upper horizontal into open ends of verticals.
Tighten set screws to secure.
3) Slide vertical extrusion over exposed ends
of brackets in lower horizontal.
Tighten set screws to secure.
Corner Bracket Installation
CEI-152 Profile
TS RV 4
Bracket
V4
V4
Insert two-piece
bracket into the
interior center slot
of extrusion.
Slide V4 Connectors
into front & back
interior grooves.
Secure inserted half of
bracket & connectors
using set screws.
Slide connecting
extrusion over
exposed ends
of bracket &
connectors.
Completed
Assembly
Secure extrusion,
using remaining
set screws.
Set
Screws
Straight Bracket Installation
TS RV 2
Upper
Horizontal
Lower
Horizontal
Upper
Horizontal
Lower
Horizontal
TS RV 2
Insert L-Brackets into the
Interior Center Slot & outer
interior grooves of extrusion.
Slide verticals over
brackets of lower
horizontal, then slide
upper horizontal &
brackets into grooves
& center slots
of verticals.
12 Brackets Total:
(4) - TS RV 2
(8) - A1 L-Brackets
A1
A1
A1
A1
Completed
Assembly
Corner Connection
1) Slide TWO-PIECE TS RV 4 straight bracket into
Interior Center Slot of extrusion, so that two of the
set screws are inside groove. Tighten two set screws
to secure.
3) Slide connecting extrusion over exposed ends of
bracket & connectors. Tighten all remaining set screws
to secure extrusions.
2) Slide two V4 Connectors into outer interior grooves
of extrusion, so that one set screw is inside groove.
Tighten set screw.
Straight Connection
Disassembly
1) Loosen set screws on brackets and slide
extrusions off of brackets.
CEI-152 Frame Assembly
CEI152 Frame Assembly
© 2022
Order #XXXXX
CEI-110 Profile
Straight Bracket Assembly
1) Slide TWO-PIECE TS RV 4 straight bracket into
Interior Center Slot of extrusion, so that two of the
set screws are inside groove. Tighten two set screws
to secure.
3) Slide connecting extrusion over exposed ends of
bracket & connector. Tighten all remaining set screws
to secure extrusions.
2) Slide one V4 Connector into outer interior groove
of extrusion, so that one set screw is inside groove.
Tighten set screw.
TS RV 4
Bracket
V4
Insert two-piece
bracket into the
interior center slot
of extrusion.
Slide V4 Connector
into front interior
groove.
Secure inserted half of
bracket & connector
using set screws.
Slide connecting
extrusion over
exposed ends
of bracket &
connector.
Completed
Assembly
Secure extrusion,
using remaining
set screws.
Set
Screws
Straight Connection
Corner Connection
TS RV 2
Upper
Horizontal
Lower
Horizontal
Upper
Horizontal
Lower
Horizontal
TS RV 2
8 Brackets Total:
(4) - TS RV 2
(4) - A1 L-Brackets
A1
A1
Slide verticals over
brackets of lower
horizontal, then slide
upper horizontal &
brackets into grooves
& center slots
of verticals.
Completed
Assembly
Insert L-Brackets into the
Interior Center Slot & outer
interior grooves of extrusion.
Disassembly
1) Loosen set screws on brackets and slide
extrusions off of brackets.
1) Slide TWO-PIECE TS RV 2 L-bracket into
Interior Center Slot of extrusion so that two
set screws are inside groove.
Tighten two set screws to secure.
2) Slide one A1 L-Bracket into outer interior
grooves of upper and lower horizontals.
Tighten set screws to secure.
4) Slide exposed ends of installed brackets of
upper horizontal into open ends of verticals.
Tighten set screws to secure.
3) Slide vertical extrusion over exposed ends
of brackets in lower horizontal.
Tighten set screws to secure.
Corner Bracket Assembly
CEI-110 Frame Assembly
CEI110 Frame Assembly
© 2022
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation
© 2022
Crate 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
CRATE PACKING
Crate Packing
© 2022
Step 1 of 10
Order #XXXXX
Locked layer contains
placeholder marks.
Hole for wire
management
Steps:
Refer to the CEI152 Frame Assembly general information page.
1) Install U-Channel to horizontal [5]. See U-Channel Attachment detail.
2) Assemble verticals [1-2], [3-4] together.
3) Connect vertical assemblies [1/2], [3/4] between horizontals [5,6].
4) Attach horizontal [7] between vertical assemblies [1/2], [3/4].
5) Install Base Plates [8] to bottom of horizontal [5], using bolts & wing nuts.
FRONT VIEW
Item
1
2
3
4
5
6
7
8
--
Qty.
1
1
1
1
1
1
1
2
1
Description
96”h CEI152 Vertical Extrusion
49.823”h CEI152 Vertical Extrusion
96”h CEI152 Vertical Extrusion
49.823”h CEI152 Vertical Extrusion
56”w CEI152 Horizontal Extrusion
56”w CEI152 Horizontal Extrusion
52.353” Z140 Horizontal Extrusion
8” x 22” Base Plate
U-Channel
When assembled
U-Channel Attachment
Slide V4 connectors into
top groove of horizontal
extrusion. Tighten set-
screws to secure.
Use bolts to connect
U-Channel to
horizontal.
V4
connector
bolts
set
screws
*
*
1
3
4
6
7
U-Channel
88
5
2
Backwall Assembly
© 2022
Step 2 of 10
Order #XXXXX
Locked layer contains
placeholder marks.
Item
9
10
Qty.
2
4
Description
96”h RSG540 Vertical Extrusion
19.722” Z45 curved Horizontal Extrusion
When assembled
Steps:
1) Connect horizontals [10] between verticals [9] &
lightbox verticals [1/2], [3/4], inserting Infill.
99
10
10
10
10
I
n
f
i
l
l
I
n
f
i
l
l
1/2 3/4
Backwall Assembly (cont’d)
Tabla de contenidos
Otros manuales de Monitor de Eco-Systems
