EccoPC 3X Manual de usuario
User's Guide
computer EccoPC Desktop
3X / 5X / 7X
Producer responsibility:
PRZP –Systemy Informacyjne Sp. z o.o.
Street: Kilińskiego 6, 28-230 Połaniec, Poland
NIP: 866-16-96-830,
Regon: 260255419,
KRS: 0000492713,
e-mail: [email protected]
tel. (15) 868 55 90
p. 2
Introduction
Congratulations on your purchase of a personal computer brand EccoPC.
We are confident that it will meet your high expectations. This manual will familiarize you with the
elements and features of the computer. We have made every effort to provide you with in this
publication is complete and accurate information about the purchased product. However, we do
not accept liability for any errors. In case of problems, please refer to your dealer. We will be
grateful to you for any error indications, suggestions for improvement and criticism. All rights
reserved. This publication or any part thereof may not be reproduced in any form (print,
photocopy, microfilm, etc.), or processed or distributed in electronic form without the prior
written permission of the manufacturer. Other product names may be registered trademarks and
must be treated as such.
We wish you a lot of job satisfaction with our product:
Team PRZP Systemy Informacyjne
p. 3
Table of Contents
Introduction ........................................................................................Błąd! Nie zdefiniowano zakładki.
Table of Contents ................................................................................Błąd! Nie zdefiniowano zakładki.
General information ............................................................................Błąd! Nie zdefiniowano zakładki.
Technical data .....................................................................................Błąd! Nie zdefiniowano zakładki.
Safety in use ........................................................................................Błąd! Nie zdefiniowano zakładki.
Environmental Protection...................................................................................................................9
Installation and use ..........................................................................................................................14
Warranty..........................................................................................................................................33
p. 4
General Information
Comments on the regulations in force in the European Union
Declaration of Conformity
Products with the CE marking comply with at least one of the following EU directives that
apply to the product:
Directive 2006/95 / EC on low voltage devices, Directive 2004/108 / EC on electromagnetic
compatibility, Directive 2009/125 / EC on ecodesign Directive 1999/5 / EC on radio
equipment and telecommunications, the RoHS Directive 2011/65 / EC.
Compliance with these directives determined using the relevant European harmonized
standards.
Important information regarding the WEEE Directive
Marking WEEE products PRZP Systemy Informacyjne is compliant WEEE (European
Parliament 2002/96 / EC). The devices are labeled in accordance with the rules on waste
electrical and electronic equipment (ang. Waste electrical and electronic equipment - WEEE).
These rules define the infrastructure, return and recycling of used equipment. The marking is
applied to various products to indicate that at the end of life should not be thrown away, but
transferred to the organized collection points for recycling.
Users of electrical and electronic equipment labeled with WEEE can not
p. 5
throw it to the end of life as unsorted municipal waste, but must pass it to an organized
network of collection points for materials recovery and recycling to minimize the potential
danger to human health and the environment from hazardous substances in electrical and
electronic equipment. To transfer equipment for recycling or proper disposal, use the public
collection system or return them to PRZP Systemy Informacyjne (according to the WEEE
Directive).
p. 6
Technical data
Working environment:
Temperature: 5 ° C - 35 ° C
Air humidity: 30% - 70% relative humidity (non-condensing)
Power supply:
The computer requires alternating current 50/60 Hz. Connect the computer to a power source
using the included cable. To disconnect the power supply, remove the cord from the socket. Use
socket earthed. The supply voltage (AC) is 200-240 V.
Tip
The device complies with standards for interference emissions EN 55022 and EN 61000-3-2
standard for interference, and the EN 55024 electrical safety standard EN 60950. The introduction
of changes to the system without the permission of the manufacturer will void the manufacturer's
warranty as to the compatibility of these standards. Disposal in accordance with the instructions
in this manual guarantees compliance with European Union standards.
Notes User
This device has been designed and tested to prevent radio interference. Using external cables,
please take the following into account: Using cables other than those supplied by the
manufacturer with your computer, make sure that they meet the same specifications as the
original wires. Use only shielded cables and make sure that all peripheral devices are CE certified.
Failure to comply with these requirements means that the company can not provide any
guarantee for compliance with regulations and standards.
p. 7
Safety in use
Use of
This product should only be used according to the manufacturer's instructions.
It is essential to comply with the requirements concerning the working environment and the
power supply parameters.
This product is not intended for medical purposes, sustain or save lives.
Important Safety Information
The computer may be heavy; remember that during his transfer to follow the procedures in line
with the lifting ergonomics.
To reduce the risk of electric shock or damage to the equipment:
• Plug the power cord into an electrical outlet located in
easily accessible place.
• The computer must be disconnected from the mains by unplugging the power cord
from the wall outlet.
• If provided with a power cord equipped with a 3-prong plug, it must be connected to a
grounded 3-pin outlet. Do not in any way block the grounding pin plug cord (eg. By
attaching a 2-pin adapter). Ground prong has a very important safety feature.
The computer should be installed near a power outlet. The power cord is the main element to
disconnect the computer from the mains and must always be easily accessible. For your safety,
the power cable provided with your computer has a grounded plug. Power cable must always be
used with a properly grounded wall outlet, to avoid electric shock.
Do not use the computer with the cover.
p. 8
For safety reasons, before performing any maintenance procedures, always unplug your computer
from the power source and any telecommunications systems (eg. Telephone lines), networks and
modems. Failure to do so may result in personal injury or damage to equipment. Voltage levels of
electric current occurring in the power supply circuits and computer modem are dangerous.
If your computer is equipped with a voltage selector switch 115 V or 230 V, the initial setting of
this switch corresponds to the voltage applicable to the country / region in which you purchased
the device. Incorrect setting of the voltage selection switch could damage your computer and void
any implied warranty.
Not tested connecting this product to the computer power supply systems (power distribution
systems with alternating current without a direct connection to earth, according to IEC / EN
60950).
Installation conditions
• Before connecting the device to an external power source, refer to the installation
instructions.
• The device must be equipped with a proper earth connection of alternating current.
• Inside the computer elements may be energized or moving. Disconnect the power
supply before removing the cover. Before reconnecting power create and secure housing.
p. 9
Laser (Safety tip)
Warning!
With the lid open laser radiation!
This radiation is present in the CD drive. When dismantling and / or opening this drive, be
careful:
• not to look into the beam, even using optical instruments.
• Avoid contact with radiation
• Avoid both direct and diffuse irradiation of the eyes and skin.
Failure to follow these guidelines can in the worst case lead to permanent blindness. Built in the
computer CD-ROM drives do not have any parts that require maintenance or repair. CD drives can
be repaired only by the manufacturer. This product can be mounted laser class 1 to 3B. When the
housing is closed, the device qualifies for Class 1. By opening the device, the drive can be regarded
as a device even Class 3B. Built in the computer CD-ROM drives do not have any parts that require
maintenance or repair. CD-ROM drives should be performed by authorized technicians.
Data safety
The responsibility for complete data backups, including of applications and operating system
software is borne entirely by the customer. Data protection must be completed before the
warranty service.
For this reason PRZP Systemy Informacyjne categorically claims that it is not responsible for any
loss of data, which could take place within the framework of fulfillment of guarantee.
p. 10
Environmental Protection
Computer environmentally friendly
System This system was constructed according to the principles of environmental protection. There is a
possibility of its extension, fit and recycling.
Long-term use of the device
This computer is a modular system. Individual components can be easily removed or
replaced. The design of the device allows the following extensions:
• Processor
• Adding or replacing memory modules
• Adding, replacement or connection of additional high capacity memory
• Adding or replacing hard drives
• Improve the graphics card
• Free connectors for individual extensions
Please refer to the accompanying instructions as to guarantee.
The construction of the device of reusable components
This device produced with concern for the environment (the producer meets the requirements of
ISO 14001) In the process of production, the producer took into account the following aspects:
• Avoid non detachable connections of different materials. Mechanical connections must be easily
separated.
• Avoiding material surrounded by another material
• Easy disassembly and repair
• Reduction variety of materials
• Reduce the use of plastic housing parts
• Most of the housing is made of the same material.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
