EBARA ESA70W Manual de usuario
EBARA Corporation
ESA70_STD_2_E_Rev.0
INSTRUCTION MANUAL
MULTI-STAGE DRY VACUUM PUMP
MODEL ESA70W
MODEL ESA70WN
STANDARD MODEL
200V（50Hz）、200-220V（60Hz）
Caution:
Please read and understand this INSTRUCTION MANUAL thoroughly
before using this equipment.
Be sure to keep this INSTRUCION MANUAL on hand for future
reference
To Facility and Tool Manufactures:
Be sure to distribute this INSTRUCTION MANUAL to all end-user
personnel actually operation this equipment.
※「Model ООО」in this INSTRUCTION MANUAL is our model code
ISSUED BY PRECISION MACHINERY GROUP
EBARA Corporation
Do not reproduce or reprint any portion of this manual without permission.
Manufacturer reserves the right to discontinue or change any specifications or
designs without notice and without incurring obligations.
Model OOO in this catalog is our model code.
All rights reserved, copyright EBARA
(i)
EBARA Corporation
Environmental Basic Policies
It is our responsibility, as people of the earth, to protect nature's irreplaceable
treasures and to pass them on to future generations.
As we undertake our business activities, we will establish environmental
management systems and implement ongoing improvements and reviews, while
striving to promote harmony between technology and nature, prevent
environmental pollution, and improve the overall results of our environmental
management activities. We are aware that environmental protection and
management activities are the responsibility of all managers and employees of the
Corporation, and each person will demonstrate this awareness when carrying out
his or her duties.
We will widely publicize these basic policies to regional societies and the general
public and work to make Ebara's position on the environment clear to society in
general.
(ii)
EBARA Corporation
Safety Information
It is essential that those operating this pump should have the knowledge to identify and avoid
hazardous conditions associated with the pump.
Improper or rash operation may cause dangerous accidents and serious injuries.
Before installation and operation, the operator should first have a good knowledge of the
pump construction, operation procedure, and its hazards.
The operator should read through this instruction manual and other documents issued by
EBARA in detail.
If you have any questions on pump operation, safety, or maintenance, please does not
hesitate to contact EBARA directly. Refer to Global network for contact address.
Three terms designating the level of hazard are used in this manual.
DANGER Indicates an imminently hazardous situation that, if not avoided, will
result in death or serious injury.
WARNING Indicates a potentially hazardous situation that, if not avoided, could
result in death or serious injury.
CAUTION Indicates an imminently hazardous situation that, if not avoided, may
result in minor or moderate injury. This term may also be used as a
warning for situations liable to damage equipment
(iii)
EBARA Corporation
Important Prior Warnings
DANGER Keep out from under the pump when lifted.
Only qualified personnel shall unload and lift the pump.
Keep pump at horizontal position when lifted.
Do not lift the pump without eyebolt spacer.
WARNING Be careful not to overturn the pump when pushing and pulling it
sideways, because the pump is narrow in comparison to its height.
WARNING Only a qualified electrician should perform electrical works,
observing all national and local electrical regulations.
WARNING Interrupt Earth Leakage Breaker (ELB) before starting on Cut and lock out power
before beginning wiring and or maintenance work.
Do not switch on the power supply to the pump until work is completed and pump
and piping are returned to safe operating condition.
WARNING Supply N2 gas to the exhaust piping when necessary to dilute the flammable or
toxic gas down to a safe concentration.
WARNING Purge with sufficient N2 gas before removing and cleaning the vacuum and
exhaust piping.
Do not let inflammable, toxic or dangerous materials disperse and guard against
contact with the human body.
Always work in a location with an escape route in an emergency.
WARNING Do not use the pump for another process without a previous overhaul. Gases or
reaction products remaining in the pump will react and lead to accidents with the
formation of large amounts of byproducts.
WARNING Pump oil may be contaminated with process byproducts. Treat it as a hazardous
waste. See Table 3.1 for oil quantities.
(iv)
EBARA Corporation
WARNING Exhaust from pumps handling process gases should be connected to an
appropriate exhaust abatement system that is equipped with discharge quality
monitors to provide warnings and shut down the process gas flow if gas
concentrations exceed allowable limits.
WARNING Check for gas leaks after installing and maintaining the piping.
Gas leaks will result in the discharge of harmful and dangerous substances and
in abnormal reactions due to the ingress of air into the pump. When checking for
gas leaks by pressurization, please pressurize by less than 0.05 MPa into the
purge port and do check.
WARNING Do not alter the pump member nor change any parts without EBARA’s consent or
approval.
WARNING The pump casing and exhaust piping become extremely hot during operation and
remain hot for some time after stopping.
Be sure that pump and exhaust piping do not come in contact with humans or
inflammable substances.
Do not remove pump enclosure panels during operation
WARNING Check Safety Interlock functions periodically (every 6 months) to confirm correct
operation.
CAUTION Disposal of process by-products shall be strictly in accordance with all local and
national environmental and safety regulations
CAUTION Disposal of Printed circuit board containing lithium battery shall be strictly in
accordance with all applicable local and national environmental regulations.
WARNING In designing the dry pumps, Ebara does not assume risks caused by hazardous
chemical reactions resulted from simultaneous injection or mixture of multiple
process gases in the pumps, and the pump is not equipped with a protection
against the dangers from such pump usage. The tool suppliers and users must
pay attention not to simultaneously inject or mix those gases.
WARNING Do not perform a withstand voltage test.Failure to comply could
result in damage to the sensitive devices.
(v)
EBARA Corporation
CAUTION Never operate the pump without pump cover for safety.
(vi)
EBARA Corporation
The following safety warning labels are attached to pump covers.
1. High temperature warning
2. Hazardous voltage warning
3. Hazardous materials warning
4. Electric charge mark
5. Hazardous weight danger
6. High temperature eyebolt warning
1. High temperature warning
Hot surface may burn or cause injury.
Allow the piping and casing to cool before servicing.
2. Hazardous voltage warning
Hazardous Voltage may shock, burn, or cause death.
Turn power off and lockout before servicing.
WARNING 警告
Hot Surfaces
Will burn skin on contact.
Allow piping and casing to cool
Before servicing
高温部あり。接触すると火傷をする危険があります。
配管・ケーシングが冷えてからメンテナンスをして下さい。
C-7110-312-0001
WARNING 警告
Hazardous Voltage
Contact will cause injury or death by
electrical shock. Disconnect
line power before servicing.
危険電圧部あり。接触すると重傷または死亡の
危険があります。電源供給を止めてブレーカを切った状態で
メンテナンスをして下さい。
C-7110-313-0001
(vii)
EBARA Corporation
3. Hazardous materials warning
In case of hazardous materials are handled. Run the pump only with
N2 gas purge before servicing. Take adequate measures against
dangerous reaction and contact with human body.
4. Electric charge mark
5. Hazardous weight danger
Heavy weight may cause severe injury or death due to overturning
or falling pump. Keep out from under the lifted pump.
Raise all adjuster-feet fully when moving.
WARNING 警告
Hazardous Materials
Exposure to air may cause spontaneous fire or explosion.
Inhalation or skin absorption will cause severe injury or
death by poisoning.
Purge thoroughly with nitrogen for at least 30 minutes
before servicing. Use personal protective equipment
a
pp
ro
p
riate to the materials to
p
revent ex
p
osure.
危険物質あり。
危険反応・人体への接触により重傷または死亡の危険があります。Ｎ２パージのみで３０分以上
空運転を行なってから、危険物質のＭＳＤＳに従ってメンテナンスをして下さい。
C-7110-314-0001
危険
Heavy Object
Can cause impact injury through falling or tipping.
Use appropriate, properly rigged lifting equipment and keep from
under suspended pump. Raise all adjuster feet fully when moving.
重量物。落下及び転倒により重傷または死亡の危険があります。
吊り上げたポンプの下に入らないで下さい。
移動時は全アジャスタフットを上限まであげて下さい。
C-7110-316-0001
(viii)
EBARA Corporation
6. High temperature eyebolt warning
Hot surface may burn or cause injury.
Allow the eyebolt to cool before servicing.
WARNING 警告
Hot Surfaces.
Will Cause burn. Do not touch eyebolts
during pump running for some time after stops.
高温部あり。火傷のおそれがあります。
ポンプ運転中及び停止後しばらくの間はアイボルト部に
触れないで下さい。
C-7110-317-0001
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Bomba de agua de EBARA
EBARA
EBARA DDLFU Manual de operación y mantenimiento
EBARA
EBARA Ego Instrucciones de funcionamiento
EBARA
EBARA 3U Manual de operación y mantenimiento
EBARA
EBARA BEST ONE Instrucciones de funcionamiento
EBARA
EBARA 3E Series Manual de usuario
EBARA
EBARA ESA300W Manual de usuario
EBARA
EBARA EVM Manual de usuario
EBARA
EBARA 3SF Manual de usuario
EBARA
EBARA SF6 Instrucciones de funcionamiento
EBARA
EBARA 3D Instrucciones de funcionamiento
EBARA
EBARA EPD Manual
EBARA
EBARA EV-A03 Manual de usuario
EBARA
EBARA JEU Manual de operación y mantenimiento
EBARA
EBARA GS Manual de usuario
EBARA
EBARA EV-S20 Manual de usuario
EBARA
EBARA DMLU Manual
EBARA
EBARA DAR Manual de usuario
EBARA
EBARA MR Manual de usuario
EBARA
EBARA EVMSN3 Instrucciones de funcionamiento
EBARA
EBARA OPTIMA/BEST-RIGHT-DW Instrucciones de funcionamiento
Manuales populares de Bomba de agua de otras marcas
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guía de solución de problemas
DUROMAX
DUROMAX XP WX Series Manual de usuario
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manual de usuario
Franklin Electric
Franklin Electric IPS Manual de usuario
Xylem
Xylem e-1532 Series Manual de usuario
Milton Roy
Milton Roy PRIMEROYAL Manual de usuario