Eaton Eaton series Manual de usuario

Revision 01

Battery Upgrade Instructions

For use with the Eaton®9355 (20–30 kVA)

Eaton Series

Eaton reserves the right to change speci ications without prior notice. Eaton is a registered trademark o Eaton. All other trademarks are

property o their respective companies.

express written approval o Eaton.

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

This manual contains important instructions that you should follow during installation and maintenance

of the UPS and batteries. Please read all instructions before operating the equipment and save this

manual for future reference.

CONSIGNES DE SÉCURITÉ IMPORTANTES — CONSERVER CES INSTRUCTIONS

Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute

procédure d installation et de maintenance de la PDU. Veuillez consulter entièrement ces instructions

avant de faire fonctionner l équipement et conserver ce manuel afin de pouvoir vous y reporter

ultérieurement.

Battery Upgrade Instructions or 9355 (20–30 kVA) —Rev 01 iii

TTaabbllee ooff CCoonntteennttss

11 IInnttrroodduuccttiioonn....................................................................................................................................................................................................................................................................................................11

22 BBaatttteerryy UUppggrraaddee PPrroocceedduurree........................................................................................................................................................................................................................................................33

2.1 Complete UPS Battery Upgrade Procedure ......................................................................................................9

iv Battery Upgrade Instructions or 9355 (20–30 kVA) —Rev 01

Table o Contents

Battery Upgrade Instructions or 9355 (20–30 kVA) —Rev 01 1

CChhaapptteerr 11 IInnttrroodduuccttiioonn

The two-row battery tray (P/N: P-103000933, revision 5) that was used for the 9355 20-30kVA is now

discontinued. Upgrade kit P-106000220 facilitates replacing one existing two-row battery tray assembly with

two single-row battery assemblies (with two-circuit connectors). Along with an adapter harness, it is

permanently installed in the UPS to convert from single-circuit battery tray connections to the two-circuit

connectors to mate with the pair of new single-row assemblies.

Figure 1. Discontinued Two-Row Battery Tray P-103000933

Figure 2. Upgrade Kit P-106000220 Two Cartons) Includes Two Single-Row Battery Trays and Wiring

Harness Adapter

2 Battery Upgrade Instructions or 9355 (20–30 kVA) —Rev 01

Figure 3. Wiring Harness Adapter P-152001881

The total battery string voltage in a 9355 20-30 kVA UPS is 216V (18 batteries, where is each battery is 12V

nominal). The single-tray configuration that is being replaced holds 18 batteries. Two strings fit in each battery

shelf of the 9355 20-30 kVA UPS. The single-tray red connector is the most positive connection while the black

is the negative connection. The white connector presents the middle point in the single-tray configuration,

where 108V is measured from the white to the red and 108V from the white to the black. The white connector

is used for CSE testing only.

The replacement tray sets contain nine batteries each, such that it takes two trays to complete one string.

Each P-106000220 kit includes two single-row battery trays and two harness adapters. Only one harness

adapter is needed for the installation; the second harness adapter is a spare.

Introduction

Battery Upgrade Instructions or 9355 (20–30 kVA) —Rev 01 3

CChhaapptteerr 22 BBaatttteerryy UUppggrraaddee PPrroocceedduurree

WARNING

This procedure involves interacting with components that may be energized.

Any and all work can involve hazards when working on electrical equipment. The work must be done in

accordance with all applicable local, federal, or other safety requirements and must be performed by qualified

personnel.

1. Remove the 9355 20–30kVA front door (see Figure 4).

Figure 4. Remove the UPS Front Door

IMPORTANT

In the event of input power failure while performing this procedure, battery backup will not be available.

2. Follow the instructions in the manual to place the 9355 20-30kVA UPS in bypass and in maintenance

bypass. However, if the UPS cannot be placed in maintenance bypass, this procedure can still be

performed.

3. Open the UPS battery circuit breaker CB2 (see Figure 5). Follow lockout/tagout procedures.

4. Remove the thirteen M5 bolts from the battery panel cover (dead front) and remove it (see Figure 5).

4 Battery Upgrade Instructions or 9355 (20–30 kVA) —Rev 01

Figure 5. Open the Battery Circuit Breaker CB2 and Remove the Battery Dead Front

5. As shown in Figure 6, disconnect the positive (red) and negative (black) battery connectors for all the

battery trays.

NOTE If an external battery cabinet is attached, it must also be disconnected from the UPS.

Figure 6. Disconnect All Battery Trays

Battery Upgrade Procedure

Battery Upgrade Instructions or 9355 (20–30 kVA) —Rev 01 5

WARNING

All battery trays must be disconnected before proceeding.

6. Remove the two M5 bolts that secure the retaining bracket on the battery shelf for the battery tray to be

replaced (see Figure 7).

Figure 7. Remove the Battery Retaining Bracket

7. Remove the existing two-row battery tray from the unit (see Figure 8).

Battery Upgrade Procedure

6 Battery Upgrade Instructions or 9355 (20–30 kVA) —Rev 01

Figure 8. Remove the Old Two-Row Battery Tray

8. Slide two new single-row trays in place of the tray that was removed. The two new single-row trays are

now side-by-side with one old dual-row tray on the same shelf, forming two battery strings (see Figure 9).

Figure 9. Slide Two Single-Row Battery Trays into Place

9. Re-install the battery retaining bracket and secure using the two M5 bolts removed in Step 6(see

Figure 10).

10. Cut the tie wrap securing the UPS battery harness to the battery retaining bracket (see Figure 10).

Battery Upgrade Procedure

Otros manuales para Eaton series

Este manual sirve para los siguientes modelos

Otros manuales de Unión Postal Universal de Eaton

Eaton

Eaton SOMATOM Manual de usuario

Eaton

Eaton 9315 Manual de usuario

Eaton

Eaton EX Pulsar Series Manual de usuario

Eaton

Eaton Powerware 3105 UPS Manual de usuario

Eaton

Eaton Tripp Lite SmartPro Series Instrucciones de montaje

Eaton

Eaton Ellipse PRO 650 Manual de usuario

Eaton

Eaton 5E Manual de usuario

Eaton

Eaton Powerware 9155 Manual de usuario

Eaton

Eaton 93E MK2 Manual de usuario

Eaton

Eaton Powerware 5125 Manual de usuario

Eaton

Eaton 9395 Plus 1 Manual de usuario

Eaton

Eaton 9PXM Manual de usuario

Eaton

Eaton Powerware 9390 Manual de usuario

Eaton

Eaton FERRUPS Manual de usuario

Eaton

Eaton Powerware 9395 Manual de operación y mantenimiento

Eaton

Eaton 9390 UPS 100160 kVA Manual de usuario

Eaton

Eaton Powerware 9140 Manual de usuario

Eaton

Eaton 5E Gen2 Instrucciones de montaje

Eaton

Eaton 9EEBM240 Manual de usuario

Eaton

Eaton Power Xpert 9395 Manual de usuario

Eaton

Eaton Powerware 9395 Manual

Eaton

Eaton Powerware 9125 Manual de usuario

Eaton

Eaton 9PX1000IRT2U-L Instrucciones de montaje

Eaton

Eaton Powerware 9390 Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario

ZincFive

ZincFive BC Series Manual de usuario