Eaton DIN24240DC Manual de usuario

p/n: 934184

Revision A

Power On/O

Power

Fault BAT

DIN Rail UPS

DIN24240DC

Remote On/O

On Battery

Replace Battery

Battery Missing

Low Battery

Input Output

[+] [-]

[+] [-] [+] [-]

COM

Quick Start Guide

Eaton Din Rail DC UPS DIN24240DC / DIN24480DC / BPDIN24XL

Eaton reserves the right to change specifications without prior notice Eaton is a registered trademark of Eaton All other trademarks are

properties of their respective companies All other trademarks are property of their respective companies

express written approval of Eaton

SSaaffeettyy IInnssttrruuccttiioonnss

IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

This manual contains important instructions that you should follow during installation and maintenance

of the UPS. Please read all instructions before operating the equipment and save this manual for

future reference.

• This UPS contains its own energy source (batteries).

• The D mains power must be turned off before connecting or disconnecting wires to the

terminals.

• Use RED wire for (+) positive and BLA K for (-) negative wire connections.

• Make sure the wires do not touch to chassis during their connection.

• Always connect the D mains input and load output wires first, then the UPS battery terminals

labeled (BAT +/-), and finally to the EBM.

• To reduce the risk of fire or electric shock, install this UPS in a temperature and humidity

controlled, indoor environment, free of conductive contaminants. Ambient temperature must not

exceed 50° (122°F). Do not operate near water or excessive humidity (95% max).

• To comply with international standards and wiring regulations, the total equipment connected to

the output of this UPS must not have an earth leakage current greater than 1.5 milliamperes.

• To guarantee sufficient convection cooling, please keep a clearance of 50mm above, 180mm

below, and 10mm lateral distance of between devices.

• Note that the enclosure of the device can become very hot depending on the ambient

temperature and load of the power supply. Risk of burns!

• Do not introduce any objects into the unit.

• The UPS and EBM unit should be installed in minimum IP54 rated enclosure.

• The units must be installed in a cabinet or room (condensation free environment and indoor

location) that is relatively free of conductive contaminants.

This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by

AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the

UPS.

Eaton Din Rail UPS Quick Start Guide 934184—Rev A 1

CChhaapptteerr 11 IInnssttaallllaattiioonn

11..11 PPhhyyssiiccaall FFeeaattuurreess

Figure 1. DIN24240DC / DIN244 0DC UPS Features

1 LED (Green) Input OK (Solid)/ On Battery (Flashing)

2 LED (Red) - Fault

3 Power ON/O Button

4 Battery Pack Terminal Block

5 Dry Contact Relay Terminals

6 DC Mains Input Terminal Block

7 DC Load Output Terminal Block

8 DIN Rail Mounting Clamp

2 Eaton Din Rail UPS Quick Start Guide 934184—Rev A

Figure 2. BPDIN24XL Features

Front of EBM

[+] [-]

1 DC Terminals

2 DC Terminals

3 DIN Rail Clamp

Top of EBM

[+] [-]

[+] [-][+] [-]

[+] [-]

Front of EBM

11..22 MMoouunnttiinngg tthhee UUPPSS ttoo tthhee DDIINN RRaaiill

The EATON DIN500A and DIN850A UPS can be mounted on “top hat” 35mm DIN rail in accordance with EN60715.

The DIN24240D and DIN24480D UPS can be mounted on a 35 mm DIN rail in accordance with EN60715.

For vertical mounting, the device should be installed with the input terminal block facing down.

To Mount the UPS:

1. Locate the top hook of the DIN rail mounting system on the unit with the unit slightly titled.

2. Rotate the unit till the latch of the rail mount system snaps on to the bottom of the DIN rail and the unit

cannot be rotated any further.

3. Shake the UPS slightly to ensure that it is secure.

4. heck if the UPS is facing upright and not tilting downward.

Mounting the UPS to the DIN Rail

Eaton Din Rail UPS Quick Start Guide 934184—Rev A 3

Figure 3. Mounting the UPS

Hook to top of the DIN rail

Listen for a click to ensure the UPS is secured

to the DIN rail.

11..33 MMoouunnttiinngg tthhee EE MM ttoo tthhee DDIINN RRaaiill

To Mount the BPDIN24XL EBM:

1. Locate the top hook of the DIN rail mounting system on the unit with the unit slightly titled.

2. Rotate the unit till the latch of the rail mount system snaps on to the bottom of the DIN rail and the unit

cannot be rotated any further.

3. Shake the UPS slightly to ensure that it is secure.

4. heck if the UPS is facing upright and not tilting downward.

5. Add additional BPDIN24XL extended battery modules by following the above steps and ensure that each

EBMs are at a minimum distance of 0.39in (10mm) between each module. Up to four EBM modules can

be used per UPS.

Figure 4. Mounting the BPDIN24XL EBM

Hook to top of the DIN rail

Listen for a click to ensure the UPS is secured

to the DIN rail.

Mounting the EBM to the DIN Rail

4 Eaton Din Rail UPS Quick Start Guide 934184—Rev A

11..44 DDCC MMaaiinnss aanndd aatttteerryy PPaacckk CCoonnnneeccttiioonnss

External Battery #1

External Battery #2

Input Output

To install the D input / output wiring to the UPS:

1. Use the recommended user-supplied wiring to connect the D UPS Input and Output terminals.

2. Use the recommended user-supplied EBM wiring from Table 1 to connect to the D UPS battery (BAT + /

-) terminals.

3. onnect other end of BAT wiring from the D UPS to the closet set of +/-terminals of the EBM.

4. Add additional BPDIN24XL extended battery modules by following the above steps. Ensure each of the

EBMs are at a minimum distance of 0.39 in. (10 mm) between each module. Up to four EBM modules can

be used per UPS.

5. Turn on Mains D power and check with a voltmeter to verify 24V D is present across all positive and

negative terminals. Power the UPS ON by pressing the button for 3 seconds. As long as live 24V D is

supplied to input terminals the output terminals will be live in bypass and Line operation modes.

6. For connection to remote ON/OFF, dry contacts and support information, refer to the Advanced User’s

Guide at Eaton.com.

Table 1. Recommended DC In ut and Out ut Wire Sizes

Terminal Recommended Wire Gauge

AWG (mm2) Torque N-m (in-lb)

DIN24240DC DIN24480DC

DC Input/Output 16 (1 5) 12 (4) 0 6 (5 3 in-lb)

Recommended EBM Wire Size

Connection Wire Size (AWG) Torque N-m (in-lb)

Battery Terminals 12 AWG (4 sq mm) 0 6 (5 3 in-lb)

DC Mains and Battery Pack Connections

934184A

934184 A

p/n: 934184

Revision A

Power On/O

Power

Fault BAT

DIN Rail UPS

DIN24240DC

Remote On/O

On Battery

Replace Battery

Battery Missing

Low Battery

Input Output

[+] [-]

[+] [-] [+] [-]

COM

Guía de Inicio Rápido

UPS de CD Eaton para riel Din DIN240DC / DIN24480DC / BPDIN24XL

Eaton reserves the right to change specifications without prior notice Eaton es una marca registrada de Eaton Todas las demás marcas

comerciales son propiedad de sus respectivas empresas All other trademarks are property of their respective companies

express written approval of Eaton

IInnssttrruucccciioonneess ddee sseegguurriiddaadd

INSTRUCCIONES DE SEGURIDAD IMPORTANTES

GUARDE ESTAS INSTRUCCIONES

Este manual contiene instrucciones importantes que debe seguir durante la instalación y el

mantenimiento del SAI y las baterías. Lea todas las instrucciones antes de operar el equipo y guarde

este manual para referencia futura.

ADVERTENCIA!

• Este UPS contiene su propia fuente de energía (baterías .

• Antes de conectar o desconectar los cables en las terminales, debe desconectarse la

alimentación principal de CD.

• Use cable ROJO para conexiones de cableado positivas (+ y NEGRO para negativas (- .

• Asegúrese de que los cables no toquen el bastidor durante su conexión.

• Conecte siempre primero los cables de entrada y salida de carga de la alimentación principal de

CD, después las terminales de la batería del UPS etiquetadas (BAT +/- y finalmente al EBM.

• Para reducir el riesgo de incendio o descarga eléctrica, instale este UPS en un ambiente interior

con temperatura y humedad controladas, libre de contaminantes conductores. La temperatura

ambiente no debe exceder los 50 °C [122 °F]. No opere cerca del agua o humedad excesiva (95%

máx .

• Para cumplir con los estándares internacionales y reglamentos de cableado, el equipo total

conectado a la salida de este UPS no debe tener una corriente de fuga a tierra superior a 1.5 mA.

• To guarantee sufficient convection cooling, please keep a clearance of 50mm above, 180mm

below, and 10mm lateral distance of between devices.

• Tenga en cuenta que el gabinete del dispositivo puede calentarse mucho en función de la

temperatura ambiente y de la carga de la fuente de alimentación. ¡Riesgo de quemaduras!

• No introduzca objetos en la unidad.

• La unidad del UPS y el EBM debe instalarse en un gabinete especificación IP54 como mínimo.

• Las unidades deben instalarse en un gabinete o sala (ambiente y ubicación interior libres de

condensación que esté relativamente libre de contaminantes conductores.

PELIGRO!

Este UPS contiene VOLTAJES LETALES. Todas las reparaciones y servicio deben realizarse por

PERSONAL DE SERVICIO AUTORIZADO SOLAMENTE. No hay dentro del UPS PARTES A LAS

QUE EL USUARIO PUEDA DAR SERVICIO.

SAI de riel DIN de Eaton Guía de Inicio Rápido 934184—Rev A 1

CChhaapptteerr 11 IInnssttaallaacciióónn

11..11 CCaarraacctteerrííssttiiccaass FFííssiiccaass

Figure 1. Características e los UPS DIN24240DC y DIN24480DC

1 LED (Verde) Entrada OK (Permanente) /

En Respaldo por Batería (Destellando)

2 LED (Rojo) - Falla

3 Botón de Encendido y Apagado [On/O]

4 Bloque de Terminales del Módulo de Baterías

5 Terminales del Relevador de Contacto Seco

6 Bloque de Terminales de la Entrada de

Alimentación Principal de CD

7 Bloque de Terminales de Salida de Carga de CD

8 Abrazadera para Instalación en Riel DIN

Otros manuales para DIN24240DC

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Unión Postal Universal de Eaton

Eaton

Eaton Powerware 9170+ Manual

Eaton

Eaton Ellipse ECO 500 Manual de usuario

Eaton

Eaton Powerware 9140 Manual de usuario

Eaton

Eaton Ellipse ECO 500 Manual de usuario

Eaton

Eaton MX 4000 RT Manual de uso y cuidado

Eaton

Eaton 5S 850 Manual de usuario

Eaton

Eaton 93E MK2 Manual de usuario

Eaton

Eaton Ellipse MAX 600 Pulsar Series Manual de usuario

Eaton

Eaton EX 2200 RT 3U Manual de usuario

Eaton

Eaton 5P750RC Manual de usuario

Eaton

Eaton 93E UPS Manual de usuario

Eaton

Eaton 5P 750 Manual de usuario

Eaton

Eaton 3S550IEC Manual de usuario

Eaton

Eaton 9PX 1:1 Guía de inicio rápido

Eaton

Eaton Eaton 5PX Instrucciones de montaje

Eaton

Eaton Powerware 9125 Manual de usuario

Eaton

Eaton BladeUPS none Manual de usuario

Eaton

Eaton Ellipse PRO 1600 FR Manual de usuario

Eaton

Eaton ARRAY 3A3 Pro Manual de usuario

Eaton

Eaton Powerware 9125 Manual de usuario

Eaton

Eaton 9PX6K-L Instrucciones de montaje

Eaton

Eaton 5S 700VA Manual de usuario

Eaton

Eaton Powerware 5125 Manual de usuario

Eaton

Eaton 91PS Manual

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario

ZincFive

ZincFive BC Series Manual de usuario