Eaton EGR-5000 Manual de usuario
EGR-5000 Quick Start Guide Effective November 2011
The purpose of this Quick Start Guide is to guide the User through the essential steps required to
commission an EGR-5000. This Quick Start Guide is not a replacement for the complete manual
that can be found on the CD shipped with the EGR-5000. For wiring instructions and complete
descriptions of the protective functions, please consult the complete instruction manual.
This Quick Start Guide was developed using Simulation EGR-5000_V2.0.d and PowerPort-E V.3.2.
EGR-5000
Quick Start Guide
IB02602014E
Rev.
A
Contents
Description Page
Section 1: Navigation.................................... 3
Section 2: Saving Parameters ...................... 5
Section 3: Device Setup Using the Front
Panel Soft Keys ........................... 7
3.1 Setting the Basic System
Parameters................................. 7
3.2 Setting the Basic Protection
Parameters............................... 16
Section 4: Assigning/Mapping Relay Outputs
Using the Front Panel Soft
Keys........................................... 24
Section 5: Device Setup Using
PowerPort-E .............................. 27
5.1 Setting the Basic System
Parameters............................... 29
5.2 Setting the Basic Protection
Parameters............................... 33
Section 6: Assigning/Mapping Relay Outputs
Using PowerPort-E .................... 38
EGR-5000
Quick Start Guide
2
Copyright © 2011 by Eaton Corporation. All rights reserved.
Specifications and information contained herein are subject to change without notice.
EATON CORPORATION - CONFIDENTIAL AND PROPRIETARY NOTICE TO PERSONS RECEIVING THIS DOCUMENT
AND/OR TECHNICAL INFORMATION
THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTAINED THEREON, IS CONFIDENTIAL AND IS
THE EXCLUSIVE PROPERTY OF EATON CORPORATION, AND IS MERELY ON LOAN AND SUBJECT TO RECALL BY
EATON AT ANY TIME. BY TAKING POSSESSION OF THIS DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES
THAT THIS DOCUMENT CANNOT BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF EATON, AND THAT NO
PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE PRIOR WRITTEN
CONSENT OF EATON. IN THE CASE OF CONFLICTING CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN
THE STATUS OF THIS DOCUMENT.
DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY
The information, recommendations, descriptions, and safety notations in this document are based on Eaton Electrical Inc. and/or
Eaton Corporation’s (“Eaton”) experience and judgment and may not cover all contingencies. If further information is required, an
Eaton sales office should be consulted.
Sale of the product shown in this literature is subject to the terms and conditions outlined in appropriate Eaton selling policies or
other contractual agreement between Eaton and the purchaser.
THERE ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, OTHER THAN THOSE
SPECIFICALLY SET OUT IN ANY EXISTING CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE
ENTIRE OBLIGATION OF EATON. THE CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY
ANY CONTRACT BETWEEN THE PARTIES. In no event will Eaton be responsible to the purchaser or User in contract, in tort
(including negligence), strict liability, or otherwise for any special, indirect, incidental, or consequential damage or loss
whatsoever, including but not limited to damage or loss of use of equipment, plant or power system, cost of capital, loss of power,
additional expenses in the use of existing power facilities, or claims against the purchaser or User by its customers resulting from
the use of the information, recommendations, and descriptions contained herein.
EGR-5000
Quick Start Guide
EGR-5000 Quick Start Guide Effective November 2011
3
Section 1: Navigation
1.1 Basic Navigation
Navigation through the EGR-5000 menus and settings is easily accomplished using the soft keys on the EGR-5000
control panel and their corresponding functions that appear near the bottom of the LED display (see Figure 1).
Figure 1. EGR-5000 Basic Navigation.
To select a function that appears in the function area, press the soft key that is directly under that function.
Once the Menu soft key is pressed, the EGR-5000 utilizes arrows and tools that appear in the function area of the
display and correspond to the soft keys directly below (see Figure 2). Table 1 gives a summary of the arrows and
tools that may appear in the function area and a brief description of each.
Figure 2. Arrows and Tools in the Function Area.
Soft Ke
y
s
Function Area
A
rrows & Tools
EGR-5000
Quick Start Guide
4
Table 1. Arrows and Tools That Can Appear in the Function Area of the Display.
Arrow/Tool Description
The “Up” arrow scrolls up through the current menu.
The “Down” arrow scrolls down through the current menu.
The ”Left” arrow takes the User one step back to the previous menu.
The “Right” arrow takes the User to the next sub-menu.
The “Top of List” arrow takes the User directly to the top of the current menu list.
The “Bottom of List” arrow takes the User directly to the bottom of the current menu list.
The “Increase” icon will increase the active digit by one.
The “Decrease” icon will decrease the active digit by one.
The “Left Movement” arrow will take the User one digit to the left in a value.
The “Right Movement” arrow will take the User one digit to the right in a value.
The “Wrench” icon will give the User access to the parameter setting mode for a function.
The “Delete” icon allows the User to delete data or a value.
1.2 Password Entry
Before any parameter of the EGR-5000 can be changed, the User must enter a valid password using the soft keys
on the control panel. A password must be a User-defined, four digit combination of the numbers 1, 2, 3, and 4
(examples: 1224 or 2341).
Note: A default password (1234) was set at the factory. If the password has been changed, contact your System
Administrator for the new password.
To enter the password, simply press the soft keys corresponding with the numbers appearing in the function area
near the bottom of the LED display. An asterisk (*) will appear in the display as each number is entered.
Press the “OK” soft key after the password has been entered.
Figure 3. Entering the Password.
Password
Numbers
“OK” Ke
y
Soft Ke
y
s
EGR-5000
Quick Start Guide
EGR-5000 Quick Start Guide Effective November 2011
5
Section 2: Saving Parameters
When the User makes changes to the parameters, the EGR-5000 DOES NOT automatically save the changes.
Changes MUST BE explicitly saved by the User. There are two ways changes can be saved: saving individual
changes or saving multiple changes.
2.1 Making and Saving Parameter Changes
1. Use the soft keys under the display to access the parameter to be changed.
2. Press the soft key under the wrench icon then enter the password.
Figure 4. The Wrench Icon.
3. Use the soft keys to change the parameter then press the soft key under “OK”. Asterisks appears in the
display indicating a parameter has been changed.
Figure 5. The “OK” Soft Key and the Asterisk Denoting a Parameter Change.
A
sterisks
Wrench Icon
“OK” Ke
y
EGR-5000
Quick Start Guide
6
Note: If the User wishes to change multiple parameters, please skip to Step 5. If the User wishes to save the
individual parameter made at this time, complete Step 4 then end the process.
4. Press the “Ok” key. Then press the soft key under “Yes” to save the new value.
To Make and Save Multiple Parameter Changes
Note: The EGR-5000 utilizes a timeout function. If the timeout time has expired, the User may be asked to re-
enter the password.
5. Use the soft keys to access and change the other parameters to be changed then press the soft key under
“OK” after each change. An asterisk appears in the display indicating a parameter has been changed but
not saved. Likewise, an asterisk next to a higher-level parameter menu implies that one of its constituent
parameters has been modified but not saved.
6. Once all the parameters have been changed, press the “Ok” key. Then press the soft key under “Yes” to
save the new values.
EGR-5000
Quick Start Guide
EGR-5000 Quick Start Guide Effective November 2011
7
Section 3: Device Setup Using the Front Panel Soft Keys
Press the soft key
under “Menu” to
access the
“Operation” screen.
From within the
“Operation” screen,
press the soft key
under the down
arrow to access the
next parameter
screen “System
Para” (System
Parameters).
3.1 Setting the Basic System Parameters
From the “System
Para” (System
Parameters)
screen, press the
soft key under the
right arrow to
access the “System
Para” menu.
EGR-5000
Quick Start Guide
8
From the “System
Para” menu, use the
up and down arrow
keys to highlight
“Generator” then press
the right arrow key to
access the
“Generator” menu.
To edit any Generator
parameter, use the up
or down arrow keys to
select the parameter
(in this example
“Generator MVA”) then
press the soft key
under the wrench icon.
To edit parameters,
the User must enter a
valid password (see
Section 1: Password
Entry).
Enter the four-digit
password as
described in Section 1:
Password Entry. After
the password has
been entered, press
the “Ok” soft key.
Note: The EGR-5000
utilizes a timeout
function. If the timeout
time has expired, the
User may be asked to
re-enter the password.
EGR-5000
Quick Start Guide
EGR-5000 Quick Start Guide Effective November 2011
9
Use the “+” and/or “-“
keys to set the desired
Generator Voltage.
Press the “OK” soft
key to save the
setting.
If the parameter has
been changed and
after the User presses
the “OK” soft key, an
asterisk will appear
next to the changed
parameter.
To save the parameter
change, press the “OK”
soft key. The User will
be asked to “Save
Parameter Changes?”.
Press the soft key under
the “Yes” icon to save
the changes or the soft
key under the “No” icon
to reject the changes.
Note: This same
procedure can be used
to set all System
Parameter settings.
There may be some
minor text changes in
the “Save” screen, but
the procedure is the
same (see Section 2:
Saving Parameters.
EGR-5000
Quick Start Guide
10
To change the
Power Factor
setting, use the up
or down arrow keys
to select Power
Factor then press
the soft key under
the wrench icon.
To edit parameters,
the User must enter
a valid password
(see Section 1:
Password Entry).
Use the “+” and/or
“-“ keys to set the
desired Power
Factor. Press the
“OK” soft key to
save the setting.
If the parameter has
been changed and
after the User
presses the “OK”
soft key, an asterisk
will appear next to
the changed
parameter.
To save the
parameter change,
press the “OK” soft
key again (see
Section 2: Saving
Parameters.
Tabla de contenidos
Otros manuales de Dispositivo de protección de Eaton
Eaton
Eaton CVX050 Manual de usuario
Eaton
Eaton Powerware 9395 275 kVA MBM Manual de usuario
Eaton
Eaton ARCON 3G Manual de usuario
Eaton
Eaton SPD160480D3M Manual de usuario
Eaton
Eaton CHSPT2MICRO Manual de capacitación
Eaton
Eaton ARCON 2.0 Series Manual de lista de piezas
Eaton
Eaton Crouse-Hinds GFS Series Guía de configuración
Eaton
Eaton FRCmM-NA Manual
Eaton
Eaton C Series Manual
Eaton
Eaton PXS24 Series Manual de usuario
