Eaton Cutler-Hammer PanelMate Power Pro 5585... Manual de usuario

Effective 02/00

Printed in U.S.A.

I.L. 01-50533-00

Replacing the PanelMate Power Pro 5000 Color TFT Backlight Assembly,

Models 5585x, and Models 5285x

Introduction

The Backlight Replacement Kit provides replacement backlights for the PanelMate Power Pro 5000 Color TFT, models 5585x,

and models 5285x. This kit is shipped with two backlights, a disposable grounding wrist strap, and this instruction sheet.

Caution Electrostatic Discharge (ESD) can damage static-sensitive electronic components. You should perform these

procedures only at an ESD workstation.

If an ESD workstation is not available, you can provide some protection by wearing an anti-static wrist strap and

attaching it to a metal part of the system chassis.

Replacing the Backlights

The replacement backlights for PanelMate Power Pro 5000 Color TFT, models 5585x, and models 5285x are packaged and

sold separately from the PanelMate unit.

To install the backlight, follow these steps:

1. Disconnect the power source cable and any other cables from the PanelMate unit. If a high-speed interface module is

attached, remove the module.

2. Remove the electronics module cover by removing the screws holding it to the display plate assembly.

3. Disconnect the ribbon cable, and lay the cable flat.

4. Remove the standoffs, and screws from the display plate assembly connecting it to the front panel.

5. Carefully lay the display plate assembly, display module facing up, being especially careful not to damage the circuit

board.

6. Remove the four screws [1] on the corners of the display module [2], lifting the display module away from the display

plate assembly. See Figure 1.

7. Disconnect the video cable from the display module.

8. On the edge of the display module, disconnect the connectors [3] between the top and bottom backlight cartridges and

the inverter.

Page 2 I.L. 01-50533-00

Cutler-Hammer

173 Heatherdown Drive

P.O. Box 6166

Westerville, OH 43081

TEL: (614)-882-3282

FAX: (614)-895-7111

www.cutlerhammer.eaton.com

Effective 02/00

Printed in U.S.A.

Figure 1

9. A metal tab [4] on the side of the display module holds the top backlight assembly in place. Lift the end of the tab, and

gently and carefully slide the backlight cartridge [5] out. Do not pull the cartridge by the wires.

10. Gently and carefully insert the new backlight cartridge, making sure the cartridge clears the tab, and the tab is latched

after the cartridge is in place.

Caution The backlight cartridge is very fragile. Do not bend the backlight, but replace it by keeping the light perfectly

straight.

11. Reattach the connector between the backlight cartridge and the inverter.

12. Repeat steps 9 through 11 for the bottom backlight cartridge [6].

13. Reconnect the video cable to the display module.

14. Reattach the display module to the display plate assembly with the four screws.

15. Reattach the display plate assembly to the front panel with the standoffs and screws.

16. Reconnect the ribbon cable.

17. Replace the electronics module cover with the screws.

18. If used, reattach the high-speed interface module.

19. Reconnect the power source cable and any other cables.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Monitor de Eaton

Eaton

Eaton PXMP Series Manual de usuario

Eaton

Eaton Power Xpert Branch Circuit Monitor Manual de usuario

Eaton

Eaton MFD-Titan Manual de usuario

Eaton

Eaton EASY-RTD-DC-43-03B1-00 Manual

Eaton

Eaton MFD4-5-XRC-30 Manual

Eaton

Eaton E5324E Series Manual de usuario

Eaton

Eaton PanelMate Power Series Manual de operación

Eaton

Eaton PXM468K-DISP-6-XV Manual de usuario

Eaton

Eaton VFX Series Manual de usuario

Eaton

Eaton MFD-XM-80 Manual

Eaton

Eaton PXM4/6/8K Manual de usuario

Eaton

Eaton XV400 10.4" Manual de usuario

Eaton

Eaton XV360 Manual de usuario

Eaton

Eaton XV400 Manual de usuario

Eaton

Eaton PXBCM-DISP-6-XV Manual de usuario

Eaton

Eaton MFD-Titan MFD-80 Series Manual

Eaton

Eaton XV400 5.7" Manual de usuario

Eaton

Eaton Power Xpert Multi-Point Manual de usuario

Eaton

Eaton EASY-RTD-DC-43-03B1-00 Manual de usuario

Eaton

Eaton Cutler-Hammer IQ DP-4000 Manual de programación

Eaton

Eaton Cutler-Hammer Pow-R-Command 750 Manual de usuario

Eaton

Eaton POW-R-COMMAND 1000 Manual de usuario

Eaton

Eaton PDI WaveStar Manual de instrucciones

Eaton

Eaton XV-102 Series Manual

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación