Eaton IQ35M-ENC Manual de usuario
IQ 35M Enclosure Installation Guide
1IQ35M-ENC IB02601010E February 2011 www.eaton.com Z205927-0A
IQ35M-ENC
RoHS
Compliant
NOTICE
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classified locations.
• The installer is responsible for conformance to all applicable codes.
• Mount this product inside a suitable fire and electrical enclosure.
This symbol indicates an electrical
shock hazard exists.
Documentation must be consulted where
this symbol is used on the product.
Product Overview
The IQ35M-ENC enclosure offers a mounting option for
IQ 35M Series energy meters that is safe from tampering
and the elements. The enclosure is equipped with DIN rail
mounting hardware for easy installation. NEMA 4X rating
ensures durability, and the keylock guarantees security
from unwanted tampering.
Dimensional Drawings
Pictured with IQ 35M meter
installed; IQ 35M meter
and IQ35M-ENC must be
ordered separately.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.
• This equipment must only be installed and serviced by qualied electrical personnel.
• Read, understand and follow the instructions before installing this product.
• Turn o all power supplying equipment before working on or inside the equipment.
• Use a properly rated voltage sensing device to conrm power is o.
DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION
Failure to follow these instructions will result in death or serious injury.
DANGER
7.2”
(182 mm)
7.1”
(180 mm)
5.7”
(144 mm)
1.8”
(46 mm)
4.9”
(123 mm)
4.4”
(110 mm)
2.5”
(62 mm)
1.8”
(45 mm)
1.9”
(47 mm)
1.4”
(35 mm)
Front Side,
Cross Section
2IQ35M-ENC IB02601010E February 2011 www.eaton.com Z205927-0A
Installation
1. Install DIN Rail Clips to the back of the IQ 35M Series
Meter
The IQ 35M Series meter is shipped with a set of three
DIN rail clips included. Insert these clips into the slots on
the back of the housing from the middle, moving outward.
Stopping pegs must face the underside of the housing.
Push clips into place until there is an audible click.
DIN Rail clip
(included with IQ 35M meter)
When attaching the clips to the underside of
the IQ 35M meter, these stopping pegs must
face in towards the meter housing surface. Set
pegs into the available slots on the meter.
When all clips are in place, the white clips must be flush
with the top edge of the housing, and the black clip must
protrude slightly past the bottom edge.
Product Diagram
1
2
3
4
5
6
1. Enclosure base
2. Enclosure cover
3. Keys, locking mechanism, and pin
4. Mounting screw caps
5. Spacer block
6. Cover screws
2. Mount the IQ35M-ENC enclosure to a wall or panel
Extreme care should be taken to protect the equipment from
drill chips, filings, and other contaminants when making
the wire entry holes and mounting the enclosure to prevent
component damage or a future malfunction.
Any holes cut into the enclosure for wire conduit conections
should be cut prior to the installation of the meter in the
enclosure. All holes should be properly sealed to maintain
the enclosure rating.
The IQ35M-ENC base can be installed using either a
2-point or a 4-point screw mounting.
A. Punch out the corner holes for 4-point mounting:
B. Drill out the center holes for 2-point mounting:
3. Install IQ 35M Onto DIN Rail Inside the IQ35M-ENC
Push the top of the IQ 35M onto the DIN rail.
Then push the bottom of the meter onto the DIN rail until
there is an audible click.
Use caps to cover screw
heads after mounting.
3IQ35M-ENC IB02601010E February 2011 www.eaton.com Z205927-0A
If necessary, the IQ 35M can be removed from the DIN rail
using a flat screwdriver to pry out the bottom (black) clip.
4. Assemble enclosure cover
Locate screw holes in each corner of the IQ35M-ENC
cover.
Insert screws.
Affix cover onto enclosure by tightening all four screws.
5. Insert spacers
Plastic spacers are provided with the IQ35M-ENC. These
fit into the enclosure on either side of the meter, filling in
the gaps and increasing protection against dust. Snap the
spacer block into pieces along the scored lines. The block
contains six spacers, but only two are needed.
Insert one spacer on either side of the IQ 35M meter.
Press the spacer until there is an audible click.
Eaton Corporation
Electrical Sector
1111 Superior Ave.
Cleveland, OH 44114
United States
877-ETN-CARE (877-386-2273)
Eaton.com
© 2011 Eaton Corporation
All Rights Reserved
Printed in USA
Publication No. IB02601010E
February 2011
PowerChain Management is a registered
trademark of Eaton Corporation.
All other trademarks are property of their
respective owners.
4IQ35M-ENC IB02601010E February 2011 www.eaton.com Z205927-0A
6. Final assembly
To install the locking mechanism, use a 6 mm (15/64”) drill
bit to drill out the needed hole. Insert the locking mecha-
nism into the hole from the inside of the shield, and insert
pin to secure the fit.
Insert locking
mechanism upward
into hole.
Insert pin through
shield and through
locking mechanism to
secure in hole.
To close the clear shield, squeeze both green buttons
while pushing the shield into place on the cover. Use the
key to secure the lock.
The IQ35M-ENC is now fully assembled.
Otros manuales de Recinto de Eaton
Eaton
Eaton CROUSE-HINDS GBXE Manual de usuario
Eaton
Eaton HT110-S42 Manual
Eaton
Eaton EX RT 5 3:1 Manual de usuario
Eaton
Eaton IQ35M-ENC Manual de usuario
Eaton
Eaton Crouse-hinds series Manual de usuario
Eaton
Eaton IBC-S Instrucciones de funcionamiento y mantenimiento
Eaton
Eaton Crouse-Hinds GHG 6 Series Manual de usuario
Eaton
Eaton Crouse-Hinds 9373-FB3 Series Manual de usuario
Eaton
Eaton RE Series Manual de usuario
Eaton
Eaton CKT16 Manual de usuario
Eaton
Eaton RE Series Manual de usuario
Eaton
Eaton Crouse-hinds series Manual de usuario
Eaton
Eaton CROUSE-HINDS MTL RackShield Series Manual de usuario
Eaton
Eaton PXM350-ENC Manual
Eaton
Eaton EBC-S Manual
Eaton
Eaton IBC-L Instrucciones de funcionamiento y mantenimiento
Eaton
Eaton IBC-SW Manual de usuario
Eaton
Eaton CI-K1 Manual
Eaton
Eaton PDI JCOMM Manual de usuario
Eaton
Eaton NEMA 1 Manual de usuario
