Eaton CF2000 Manual de usuario

AddressableTwo Loop Fire Panel

Installation and Operation Manual

2INSTALLATION AND OPERATION MANUAL 25-16330-B December 2019 www.eaton.com

Contents

INTRODUCTION TO THE MANUAL................................5

SYSTEM INSTALLATION AND DESIGN ............................6

Introduction ....................................................6

Cable & wiring ..................................................6

Project Planning .................................................7

System Design Guidelines .........................................8

Guidelines .....................................................8

Loop lengths ...................................................8

Loop loading - total number of addresses .............................8

COMPATIBLE EQUIPMENT ......................................9

SYSTEM OVERVIEW ..........................................22

Simple user interface ............................................22

User configuration and maintenance facilities .........................22

Spur tolerant soft addressing ......................................22

Integral Power Supply and Battery..................................23

TECHNICAL SPECIFICATION....................................23

Optional Functions as per EN54 Parts 2 & 4 ..........................26

Panel Inputs ...................................................26

Panel Outputs .................................................27

Output to Fire Alarm Routing Equipment (Option 7.9 EN54 Part 2).........27

Output to Fire Alarm Protecting Equipment ..........................28

Output to Fault Warning Routing Equipment .........................28

Delays to outputs (Option 7.11 EN54 Part 2) ..........................28

Dependencies on more than one alarm signal

Type C (Option 7.12.3 of EN54 Part 2) ...............................29

Optional Functions as per EN54 Parts 2&4 ...........................29

INSTALLATION ...............................................30

Mains Supply ..................................................30

Cable Segregation ..............................................30

Panel Installation ...............................................30

Installation Guide ...............................................31

3INSTALLATION AND OPERATION MANUAL 25-16330-B December 2019 www.eaton.com

Contents

Fixing Details ..................................................32

Mounting the Backbox ...........................................32

Installing Cabling ...............................................32

System Wiring .................................................33

COMMISSIONING THE PANEL ..................................34

Up/downloading using PC software.................................34

PC commissioning software ......................................34

Device input programming........................................35

Non-Latching ..................................................35

Day / Night ....................................................35

Allocate Zones/Devices ..........................................35

Sounder Trigger ................................................36

Delay Configuration .............................................36

MCP Override .................................................36

Allocation List..................................................36

Dependency detection...........................................37

Panel Fault Finding..............................................38

PANEL CONTROLS AND INDICATORS............................39

Panel Overview ................................................39

LCD Display Overview ...........................................40

System Healthy ................................................40

View Event ....................................................41

Fire Event .....................................................42

View Fires ....................................................43

View Pre-Alarm ................................................44

View Fault ....................................................45

View Disabled Address ..........................................46

View Disabled Zone .............................................48

View Disabled I/O ..............................................49

View Log .....................................................50

Operational description of the event log .............................51

Operations (Soft Reset) ..........................................52

Operations (Evacuate) ...........................................53

Operations (Silence Alarms).......................................54

4INSTALLATION AND OPERATION MANUAL 25-16330-B December 2019 www.eaton.com

Contents

Operations (Lamp Test) ..........................................55

Operations (Weekly Test) .........................................56

Access Level 2 .................................................57

Commissioning ................................................57

Panel Settings (Erase Log) ........................................58

Panel Settings (Reset Wait Mode) ..................................59

Panel Settings (Zone Re-sound Mode)...............................60

Panel Settings (Change Password) .................................61

Panel Settings (Reset Password) ...................................62

Panel Settings (Change Language) .................................63

Panel Settings (Date/Time)........................................64

Panel Settings (System Details) ....................................65

Panel Settings (Australian Mode) ...................................66

Testing (Test Device) ............................................67

Testing (Test Zone) ..............................................68

Testing (Test Sound Levels) .......................................69

Testing (One Man Walk Test) ......................................70

Testing (Global Flashing LED) screen................................71

Testing (Analogue Levels) ........................................72

Device Config (Add Device) .......................................73

Device Config (Delete Device) .....................................74

Device Config (Enable/Disable Address) .............................75

Device Config (Enable/Disable Zone)................................77

Device Config (Enable/Disable I/O) .................................78

Device Config (Check Autoconfig) ..................................79

Device Config (Change Device) ....................................80

Device Config (continued) ........................................81

APPENDIX ..................................................82

System Wiring .................................................82

Detector Base Wiring ............................................83

Addressable Call Point ...........................................84

Base sounder and sounder beacon base.............................85

Loop powered beacon ...........................................86

Internal Wall Sounder ............................................87

5INSTALLATION AND OPERATION MANUAL 25-16330-B December 2019 www.eaton.com

Contents

IP66 Wall Sounder Wiring.........................................88

3 Way Input/Output unit..........................................89

1 Channel Mains Rated I/O Wiring..................................90

Zone Monitor Unit Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Intrinsically Safe Zone Monitor Unit Wiring ...........................92

Shop Monitor Unit ..............................................93

Spur Isolator...................................................94

4 Way Sounder Controller ........................................95

Micro Zone Monitor Wiring .......................................96

Micro Input Module Wiring .......................................97

Battery Disposal Instructions ......................................97

NOTES .....................................................99

DOCUMENT UPDATE NOTES

S.No. Release / Change Notes Date

AFirst Release March 2019

BFirst Revision December 2019

Introduction to the Manual

This manual provides information on the installation, operation and maintenance of

the Eaton Fire Systems CF2000 Control Panel.

Notice

The operating system of the panel may be revised as a result of enhancements to

the system software or hardware. An updated issue of this manual is available on

request. The current issue of the manual can also be downloaded from the

Eaton website.

WARNING

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE

OF THE USED BATTERIES ACCORDING TO THE INSTRUCTIONS IN THE BATTERY

DISPOSAL INSTRUCTIONS.

6INSTALLATION AND OPERATION MANUAL 25-16330-B December 2019 www.eaton.com

System Installation and Design

Introduction

CF2000 provides all of the sophisticated features required of a leading edge analogue

addressable fire system along with the simple operation and neat installation

demanded by installers and building users.

The panel can be flush or surface mounted and the generously sized metal back box

allows ample facilities for rear or top cable entries. It is available as a two loop panel.

A comprehensive range of ancillary devices is available to operate with the

CF2000 panel, including Optical, photo-thermal and heat sensors, callpoints and a

comprehensive range of interfaces.

Each of the CF2000 system components has been specifically designed to operate as

part of a CF2000 system, this provides an assurance that the panel, the sensor, the

interfaces and the ancillaries are all fully compatible with each other and that the full

range of system functionality is supported by each device.

Each loop of the panel can accommodate up to 200 (99 Belgium) addresses.

Cable & wiring

Only the cable types listed below are allowable for loop connections.

• Enhanced Fire TUF

• Fire TUF™

• FP200

• MICC

When choosing your preferred cable type, you must take note of the following cable

and wiring requirements.

1. The cable must be 2 core screened with an over sheath

2. Maximum loop length with any of the above cables is 2KM

3. Maximum volt drop must be limited to 7 volts

4. The conductors should be 1mm2 CSA minimum to a maximum of 1.5mm2CSA

5. Multicore cable should not be used for Sensor wiring

6. Different loops should NEVER be run within the same cable

7. Loop feeds and returns should NEVER be used within the same cable

Cable resistance

Core CSA Typical FP200 resistance

1.0mm² 18.1 Ohms/km/Core

1.5mm² 12.1 Ohms/km/Core

2.5mm² 7.41 Ohms/km/Core

4.0mm² 4.61 Ohms/km/Core

7INSTALLATION AND OPERATION MANUAL 25-16330-B December 2019 www.eaton.com

System Installation and Design

Project Planning

The following is a typical program and timetable for an installation project, once the

initial order has been received:

1. Project Meeting

Installer and user to be present; system specifications, schematic diagram and

proposed circuit drawing to be available. CF2000 Installation & Commissioning Guide

to be provided.

2. Equipment Fix

Typically 2 week's notice is required for equipment to be delivered. Cable to be

installed and bases/back boxes to be fitted. Then fire sensors, call points, alarm

sounders and interface units can installed.

3. Address Schedule

Schedule of sensor locations to be completed by installer and returned to enable

System programming.

4. Auto Learn

Fire panel panels to be installed and terminated. System to be powered up by

installer and auto learn mode activated (see Auto Learn section). System to be tested

and verified by installer, prior to final commissioning.

5. Final Commissioning

Minimum 2 weeks notice is required from receipt of Address Schedule and

Commission request form for an Eaton Fire Systems Service Engineer to attend

site to implement/oversee the final commissioning procedures (see Commissioning

section), in conjunction with the installer.

8INSTALLATION AND OPERATION MANUAL 25-16330-B December 2019 www.eaton.com

System Installation and Design

System Design Guidelines

Guidelines

Fire detection and fire alarm systems for buildings should conform to the

relevant local standards and codes of practise. For the UK, these are BS 5839-1

(non-domestic premises) and BS 5839-6 (domestic premises). Both BS 5839-1 and

BS 5839-6 require the Control and Indication Equipment (CIE) to conform to

BS EN 54-2. The CF2000 fire control panel has been certified to BS EN 54-2.

Therefore, the panel is suitable to be installed in applications which have been

designed in accordance with the relevant BS 5839 codes of practise.

Installation planning is simplified by the fact that every addressable CF2000 device

contains an integral short circuit isolator. Care must be taken to ensure that local

standards requirements regarding aspects such as loop coverage, area covered by a

single spur and cable specification are observed.

There may be certain applications in which deviations from the code may be

necessary and these must be listed on the commissioning certificate (see

Commissioning the panel).

Loop lengths

The maximum permitted loop length is 2 km measured from the near to the far

terminals on the CF2000 Motherboard PCB. There is no minimum limit to loop

length. Any wiring spurs off the loop must be included within the 2 km limit. On long

loop runs, the lengths of wiring rises and falls (between floors, down to manual call

points) must be included. Remember to include these especially when taking loop

lengths from plan drawings.

Loop loading - total number of addresses

The total number of addresses per loop is 200 (99 Belgium). This includes detectors,

call points and all other addressable items and call points. When designing systems

its recommended that allowances are made for future expansion, Short circuit

isolators are incorporated into every CF2000 loop device, including Smoke detectors,

heat detectors, sounders, callpoints and interfaces. Therefore, no further fault

protection is required. In the event of a single fault, none of the devices connected

to the loop will fail to operate as the fault will be isolated by the

two adjacent devices.

Spur connected devices downstream of a cable fault will cease to function.

9INSTALLATION AND OPERATION MANUAL 25-16330-B December 2019 www.eaton.com

Compatible Equipment

Dimensions (mm) Product Codes

Description Length Width Height Model Reference Order Code

Addressable Control Panels

Addressable 2 Loop Control Panel,

Standalone 170 320 400 CF2000 910187FULL-0198

Addressable Repeater Panels

Addressable Passive Repeater N/A

Addressable Detectors: Bases

Addressable Detector Base 104 104 22 CAB300 CAB300

Addressable Detectors: Point

Addressable Multi-Mode Heat Sensor 100 100 44 CAH330 400003FIRE-0003X

Addressable Optical Smoke Sensor 100 100 34 CAP320 400002FIRE-0002X

Addressable Photo-Thermal Sensor 100 100 44 CAPT340 400004FIRE-0004X

Addressable Detectors: Speciality

Addressable Reflective Beam Detector

50-100m 120 130 210 MAB100R MAB100R

Addressable Reflective Beam Detector

5-50m 120 130 210 MAB50R MAB50R

Addressable Call Points

Addressable Manual Call Point 53 87 87 CBG370S CBG370S

Addressable Manual Call Point

(Weatherproof) 53 87 87 CBG370WP CBG370WP

Addressable Alarms and Beacons

Addressable Remote Indicator 49 87 87 MRIAD MRIAD

Addressable Beacon 53 95 95 CAB382 CAB382

Addressable Ceiling VAD

(Red Plastic, Red Flash, Shallow Base) 37 93 93 CAB482CS 812037FULL-0214X

Addressable Wall VAD

(Red Plastic, Red Flash, Deep Base) 66 93 93 CAB482WD 812036FULL-0212X

Addressable Wall VAD

(Red Plastic, Red Flash, Shallow Base) 37 93 93 CAB482WS 812035FULL-0211X

Addressable Ceiling VAD (Red Plastic,

White Flash, Shallow Base) 37 93 93 CAB492CS 812050FULL-0269X

Addressable Wall VAD

(Red Plastic, White Flash, Deep Base) 66 93 93 CAB492WD 812034FULL-0210X

Addressable Wall VAD (Red Plastic,

White Flash, Shallow Base) 37 93 93 CAB492WS 812033FULL-0209X

Addressable Sounder Base 40 102 102 CAS380 CAS380

10 INSTALLATION AND OPERATION MANUAL 25-16330-B December 2019 www.eaton.com

Compatible Equipment

Dimensions (mm) Product Codes

Description Length Width Height Model Reference Order Code

Addressable Sounder Base (Australian

Tone) 40 102 102 CAS380AU CAS380AU

Addressable Wall Sounder 96 105 105 CAS381 CAS381

Addressable Wall Sounder (Australian

Tone) 96 105 105 CAS381AU CAS381AU

Addressable Wall Sounder

(Weatherproof, Australian Tone) 103 109 108 CAS381AU-WP CAS381AU-WP

Addressable Wall Sounder

(Weatherproof) 103 109 108 CAS381WP CAS381WP

Addressable Wall Sounder Beacon 95 105 105 CASB383 CASB383

Addressable Wall Sounder Beacon

(Weatherproof) 105 108 108 CASB383-WP CASB383-WP

Addressable Wall Sounder VAD

(White Flash) 95 108 108 CASB393 CASB393

Addressable Wall Sounder VAD

(Open Class, Weatherproof) 105 110 110 CASB393WP CASB393WP

Addressable Wall Sounder VAD

(Red Plastic, Red Flash) 92 106 147 CASB483 8500111FULL-0197X

Addressable Wall Sounder VAD (Red

Plastic, White Flash, Weatherproof) 100 111 151 CASB483WP 8500115FULL-0201X

Addressable Wall Sounder VAD

(Red Plastic, White Flash) 92 106 147 CASB493 8500110FULL-0199X

Addressable Wall Sounder VAD (Red

Plastic, Red Flash, Weatherproof) 100 111 151 CASB493WP 8500114FULL-0200X

Addressable Sounder Beacon Base 44 115 115 CASBB384 CASBB384

Addressable Sounder Beacon Base

(Bell Tone) 44 115 115 CASBB384-B CASBB384-B

Addressable Sounder VAD Base

(Open Class) 44 115 115 CASBB394 666129FULL-0198X

Addressable Interfaces

Addressable 3 Channel I/O Unit

(Reset on Reset) 60 180 130 CIO351 CIO351

Addressable 3 Channel I/O Unit

(Reset on Silence) 60 180 130 CIO351S CIO351S

Addressable 3 Channel I/O Unit

(Triple Address) 60 180 130 CIO351SST CIO351SST

Addressable Micro Zone Monitor Unit 18.5 35 65 CIU872 CIU872

Addressable 230V Relay I/O Unit 60 180 130 CMIO353 CMIO353

Addressable 4-Way Sounder Controller 74 300 300 CSC354CPR CSC354CPR

Addressable Spur Isolator Unit 60 147 88 CSI350 CSI350

Addressable Zone Monitor Unit 60 147 88 CZMU352 CZMU352

Otros manuales para CF2000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Panel de control de Eaton

Eaton

Eaton MEMSHIELD 4 Manual de usuario

Eaton

Eaton EFCV8ZONE Manual de usuario

Eaton

Eaton DALI Manual de usuario

Eaton

Eaton DF6000 Guía del usuario

Eaton

Eaton VoCALL 5 Manual de usuario

Eaton

Eaton BreakerVisu NZM-XMC-MDISP35-MOD Manual de usuario

Eaton

Eaton E Series Manual de usuario

Eaton

Eaton COOPER POWER SERIES Manual de usuario

Eaton

Eaton CF3000 Manual de usuario

Eaton

Eaton 500 Manual de usuario

Eaton

Eaton BiWire Flexi Manual de usuario

Eaton

Eaton DF6100 Manual de usuario

Eaton

Eaton XV-112 Manual de usuario

Eaton

Eaton Cutler-Hammer PanelMate 3000 Series Manual de usuario

Eaton

Eaton Crouse-Hinds SynergEX EZFlex Series Guía de configuración

Eaton

Eaton XV300 Series Manual de usuario

Eaton

Eaton Greengate ControlKeeper CK4A-SSRC Manual de usuario

Eaton

Eaton Cuttler-Hammer FDAP-M Manual de usuario

Eaton

Eaton BreakerVisu NZM-XMC-MDISP35-MOD Manual

Eaton

Eaton BiWire Flexi Manual de usuario

Eaton

Eaton EASY-RTD-DC-43-03B1-00 Manual

Eaton

Eaton DX-KEY-LED2 Manual

Eaton

Eaton JSB FX4200 Series Manual de usuario

Eaton

Eaton Cutler-Hammer PanelMate Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas