Eaton MPD-C-EXT Manual de usuario

Overview

The MPD-C-EXT 12-24V microwave presence detector

switch is designed to provide automatic control of lighting,

heating or ventilation loads. It detects movement using a

highly sensitive microwave detector. This works by emitting

low power microwave signals and measuring the reflections

as the signals bounce of moving objects. The MPD-C-EXT

12-24V is optimised for ceiling mounting applications to

give detection over long distances.

When movement is detected the load is turned on. When

an area is no longer occupied the load will switch off after

an adjustable time out period.

The internal light sensor provides additional energy saving

in lighting applications. When an area is occupied lighting is

only switched on when the level of natural light is below a

preset level.

Features

Microwave Sensor

Detects movement within the unit’s detection range,

allowing load control in response to changes in occupancy.

IR Receiver

Receives control and programming commands from an IR

(infrared) handset.

Light Level Sensor

An integral adjustable photocell allows the lights to be kept

off if there is sufficient ambient light.

Presence detection

When movement is detected the load will automatically turn

on. When the area is no longer occupied the load will

automatically switch off after an adjustable time period.

Status LED

The LED flashes Red to indicate the following:

Fig 1: Front features

Walk Test LED active when movement is detected

Valid setting received

MPD-C-EXT 12-24V

Product Guide

Sensor Lens

which covers...

IR Receiver

Light Level Sensor

Status LED

To switch from more than one position simply wire two or more units in parallel to achieve two way and intermediate

switching.

The detector should be sited so that the occupants of the room fall inside the detection pattern shown overleaf, at a

recommended height of 2.8m for ceiling mounted sensors. Note that the higher the sensor is installed the shorter the

detection range will be.

 Do not site within 1m of any lighting or ventilation equipment.

 Do not fix to a vibrating surface.

 Site as far away as possible from the surface of metal objects.

 Ensure that all cable entry to the enclosure is via suitable cable glands and seal with silicone sealant where

appropriate.

 If it is necessary to screw through the rear of the enclosure ensure that any holes are covered with the caps

provided and sealed with silicone sealant where appropriate.

 Note: when externally mounted the unit may be triggered by trees, animals, leaves etc.

Wiring

NC NO

COM

Fault finding

What if the load does not turn ON?

 Check to see if the live supply to the circuit is good.

 If the supply and wiring are good, check the LUX level setting. Increase the LUX level setting to allow the

controller to turn on at higher ambient natural light level.

What if the load does not turn OFF?

 Ensure that the area is left unoccupied for a greater time period than the time out period set using the switch.

 Make sure that the sensor is not adjacent to vibrating surfaces or objects (e.g. ventilation equipment).

 The unit may pick up movement through thin partitions or walls. Reduce the sensitivity.

Programming

Parameter

Name

Default

Value

0123HHIR-PROG Handset

Graphics

Description

Button Activation

On / Raise On Turn lights on.

Off / Lower Off Turn lights off.

Walk test Off On Off When set to On this causes a red LED to

flash on the sensor when it detects

movement. Use this feature to check for

adequate sensitivity levels.

Time Out

(Time

adjustment)

10 mins 1, 10 &

minutes

5, 15 &

minutes

Once the detector is turned on, this value

sets how long the lights will stay on once

movement has ceased.

Lux on level

(Switch

level on)

92, 5 & 7 4, 6 & 9 Lux level setting to prevent the luminaires

being switched on if the ambient light level

is sufficient (adjustable between 1

and 9). The luminaires will always be

switched on at level 9.

Lux off level

(Switch

level off)

92, 5 & 7 4, 6 & 9 Lux level setting to switch the luminaires off

during occupancy if the ambient light level

goes above the setting (adjustable between

1 and 9). Level 9 will always keep the lights

on. This setting can be used for “window

row switching”.

Sensitivity 91, 5 & 9 3, 6 & 8 Sensitivity level for detecting movement.

1 = low sensitivity

9 = high sensitivity

Defaults DReturns the unit to the default settings.

Shift Use this button to select the settings in red

and blue signified by the ‘Shift 1’ and ‘Shift

2’ LEDs

Number of Shift key presses

The functionality of the MPD-C-EXT 12-24V is controlled by a number of parameters which

can be changed or programmed by any of the following devices:

 HHIR-PROG Infrared Handset. See below for programmable functions.

 HHIR-LCD-PROG Infrared Handset (with LCD). See user guide for full

programming details.

For most basic programming operations the HHIR-PROG handset can be used and the

following procedures are based on using this device.

Point the handset at the Sensor and send the required programming commands to the unit

as shown below.

Valid commands will be indicated by a red LED flash. See page 1 for details of other LED

responses.

Note: other functions on the HHIR-PROG which are not shown below are not applicable to

this product.

SHIFT 1 SHIFT 2 SHIFT 1 SHIFT 2

SHIFT 1 SHIFT 2

The allowable frequency of operation of this product is different depending on region. Please select the correct order

code using the table below.

Frequency compatibility

Technical data

Detection pattern Dimensions

Supply Voltage Min 11.5VDC max 36VDC, min 10VAC

max 26.5VAC

Power consumption On 1.01W

Off - 712mW

Load Low voltage supply with relay

output rating 16A resistive 10A inductive

Weight 0.25kg

Terminal Capacity 2.5mm2

Time out period Adjustable 10 seconds to 99 minutes.

Light level Optional adjustment by using IR

programming handsets.

Fixing method Surface fixing by screws (not supplied) .

Temperature -10ºC to 35ºC

Humidity 5 to 95% non-condensing

Material (casing) Polystyrene Type Class 2

IP rating IP 66

Compliance EMC-2014/30/EU

LVD-2014/35/EU

Safety The microwave radiation emitted by these

units is extremely low power. At a distance

of > 50mm the power density is <6% of

the ANSI IEEE C95.1 –1991

recommended microwave power density.

At a distance of 5mm from the unit it is

<84% of recommended power density.

Due to our policy of continual product improvement we reserve the right to alter the specification of this product without prior notice.

Eaton Lighting Systems

Usk House, Lakeside

Llantarnam Park,

Cwmbran, NP44 3HD, UK

Tel: +44 (0)1633 838088

Fax: +44 (0)1633 867880

lightingcontrolsolu[email protected]m

www.eatonlightingsystems.com

Ref: 9850-000614-00

#WD861 Issue 3.0

IMPORTANT NOTICE!

This device should be installed by a qualified

electrician in accordance with the latest

edition of the IEE Wiring Regulations and

any applicable Building Regulations.

Code suffix Region Frequency

blank UK, China, India, Middle East, Malaysia, Hong Kong, Singapore 10.687GHz

-R2 Australia and all of Europe except:

UK, France, Portugal, Germany, Switzerland, Austria, Slovak Republic, Republic of

Ireland

10.525GHz

-R3 France, Portugal, Switzerland 9.900GHz

-R4 Germany, Austria, Slovak Republic 9.350GHz

-R5 Republic of Ireland 10.41GHz

Otros manuales de Accesorios de Eaton

Eaton

Eaton CurrentWatch EGF Series Manual

Eaton

Eaton CurrentWatch EGF Series Manual de usuario

Eaton

Eaton 450-CSA Manual

Eaton

Eaton GHG 521 Manual de usuario

Eaton

Eaton CurrentWatch EGFL Series Manual

Eaton

Eaton CurrentWatch EDC Series Manual

Eaton

Eaton CWPD Series Manual de usuario

Eaton

Eaton Powerware Series Manual de usuario

Eaton

Eaton GHG 511 Manual de usuario

Eaton

Eaton Crouse-Hinds GHG 515 Manual de usuario

Eaton

Eaton Evolution 650 Manual de usuario

Eaton

Eaton IntelliView E76 Series Manual

Eaton

Eaton SVPD Series Instrucciones de funcionamiento

Eaton

Eaton Cutler-Hammer iProx Series Manual de instrucciones

Eaton

Eaton iProx Series Manual de instrucciones

Eaton

Eaton E67 Series Manual

Eaton

Eaton ALL-PRO MSS1301LW Manual de usuario

Eaton

Eaton CurrentWatch EGF Series Manual

Eaton

Eaton xComfort CEMU-01/ Series Manual de usuario

Eaton

Eaton CurrentWatch EPRM Series Manual de usuario

Eaton

Eaton CurrentWatch EAC Series Manual

Eaton

Eaton E55 Series Manual

Eaton

Eaton E55 Series Manual

Eaton

Eaton IntelliView Series Manual

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario